similar to: problem with X100P and wcfxo

I can either get the TE100P working or the 3 X100P clones working, but never both. I have the TE100P connected to a channel bank, and X100P clones to lines from the phone company. This is my zaptel.conf span=1,1,0,d4,ami fxsks=1-24 loadzone=us fxols=25-27 loadzone=us I then do [root@asterix root]# modprobe zaptel [root@asterix root]# modprobe wcte11xp ZT_CHANCONFIG failed on channel

[root@server ~]# modprobe zaptel [root@server ~]# modprobe wcfxo ZT_CHANCONFIG failed on channel 1: No such device or address (6) FATAL: Error running install command for wcfxo [root@server ~]# ztcfg -vvv Zaptel Configuration ====================== Channel map: Channel 01: FXS Kewlstart (Default) (Slaves: 01) 1 channels configured. ZT_CHANCONFIG failed on channel 1: No such device or address

So I took a chance with an X100P knock-off on eBay. I'm running Asterisk + FreePBX on a PowerMac G3 (beige desktop) using Slackintosh 10.2 and kernel 2.6.16.16. Everything has been fine up until now. I compile the 1.2.5 Zaptel drivers without a problem, get the udev configuration in, modprobe zaptel, and finally modprobe wcfxo. At this point, I get the message: ZT_CHANCONFIG failed on channel

I have a X100P and a TE110P in my Asterisk box. I can either get the X100P or the TE110P to work, but never both. Here's my zaptel.conf span=1,0,0,d4,ami e&m=1-24 fxsls=25 When I load wcte11xp and wcfxo, I will get this error. [root at asterix etc]# modprobe wcte11xp ZT_CHANCONFIG failed on channel 25: No such device or address (6) /lib/modules/2.4.20-8/misc/wcte11xp.o: post-install

I found similar posts regarding this error but none that answered my question. My zaptel.conf reads: fxsks=1-2 fxoks=3 loadzone=us defaultzone=us and /proc/interrupts: CPU0 0: 5542402 IO-APIC-edge timer 1: 2 IO-APIC-edge keyboard 2: 0 XT-PIC cascade 8: 3 IO-APIC-edge rtc 14: 72582 IO-APIC-edge

Hi, I'm trying to figure out why my Sweex CA000022 is not detected by wcfxo on my SuSE Pro 9.3 running on a VIA EPIA SP motherboard. The card should work as its an Intel 82537EP based card. When Booting the IRQ assignments for the board indicate: Bus Dev Func Vendor Dev Class 0 20 0 8086 1080 0703 lspci shows: 0000:00:14.0 Modem: Intel Corporation: Unknown device 1080

Hi, I'm cutting my teeth setting up a home asterisk server, but having some trouble getting Zaptel to recognize a X100P clone PCI (Motorola SM56 which should work according to various wiki's). What struck me was that the "/proc/interrupts" do not include IRQ 11 as the "lpcpi -v" is reporting. Am I missing something fundamental here? Any hint is greatly

Greetings all, I've just put two X100P cards to my box and despite trying everything I can find on the web, I can't get the second one to work. I've edited /etc/modules.conf so that ztcfg doesn't run automatically. To start, I run: /sbin/modprobe zaptel /sbin/modprobe wcfxo /sbin/ztcfg /sbin/modprobe ixj and ztcfg says: ZT_CHANCONFIG failed on channel 2: No such device or

Installing DevkitLite hardware (Very similar to John Lange's post on Tue Oct 08 2002) I cannot get anything to work on the phone connected to the s100u. I dont know what to do. Can someone please help me? I used the sample configuration files from digium documentaion that was supposed to be "sane" defaults for the kit. Very similar to John Lange's post on Tue Oct 08 2002 Here

Hello, my first post to the list. I have started to install and play with Asterisk. I was following some basic instructions to 'jump-start' my system. I have a TDM400P with one port and a X100P. I am running the latest CVS versions (from today). Following the steps I found for basic jump-start I did the following: Modprobe zaptel Modprobe wcfxo Modprobe wcfxs Edited

All, I'm having trouble getting the X100P working. Lsmod shows : zaptel 179808 0 I did a . # modprobe zaptel and here is my zaptel.conf (comments omitted) __SNIP__ fxsks=1 loadzone = us defaultzone=us __SNIP__ Here is zapata.conf __SNIP__ [trunkgroups] [channels] context=default switchtype=national signalling=fxo_ls rxwink=300 usecallerid=yes hidecallerid=no

Hmm, I don't have /etc/modprobe.conf, and wctdm is giving me problems. Which device is it talking about? [root@asterix /]# modprobe wctdm /lib/modules/2.4.20-8/misc/wctdm.o: init_module: No such device Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters. You may find more information in syslog or the output from dmesg

Hello I setup Asterisk@Home with purely VoIP and it worked fine. I then added an X100P card so I could call out / take inbound calls via PSTN and that went fine. But I have just added a TDM400P card (specifically a TDM30B) and now problems. Here is some of the output. Any ideas on what I should be looking at next? When I run genzaptelconf -s -d I get lots of erors on screen - bit I can

Hello. Well I finally rx'd my dev kit (new batch of TDM's apparently. I'm on Mandrake 9.1 There were no hardware install instructions, it would have been nice to know whether the 4-way power connector was to be used or was for some other future or expansion purpose. It came with a floppy disc, no label and it wasn't even write protected. The only readme file was

Hi Tzafrir, I am not sure what to look for, so I haveattached both the contents of /var/log/kern.log as well as the outputof dmesg. If you are looking for something specific, perhaps I can grepfor it and send you a smaller version. I have attached these as a tar ball to get below the 40K limit at which moderator approval is required. Thanks for the help. > Date: Fri, 7 Sep 2007 10:26:11

Hi, I just got my TDM400P card (2 modules) and i installed it no probs. The card is detected fine, but for some reason when I add the card to zaptel.conf i get the following error: --snip-- ZT_CHANCONFIG failed on channel 2: Invalid argument (22) Did you forget that FXS interfaces are configured with FXO signalling and that FXO interfaces use FXS signalling? --snip-- My /etc/zaptel.conf looks

I was studying the asterisk-users list archives to learn if anyone has had success with an X100P on a sparc. I noticed some postings on the subject. I am wondering if anyone has learned anything new? I have an Ultra-60 running Gentoo with 2.6.10 and udev. I built * 1.0.5 and have been enjoying various SIP configurations, with 2 sipura phones and 2 UIP200 phones (got them working!) in my home,

Hello all. I am trying to get my second x100p card set up and am having some troubles. My zaptel.conf reads: fxsks=1-2 fxoks=3-4 defaultzone=us loadzone=us before adding this card my zaptel.conf read: fxsks=1 fxoks=2-3 defaultzone=us loadzone=us But now that I've made the change I am getting the following error when running modprobe wcfxo and of course the same

I have just upgraded from Asterisk 0.7.2 to 1.0.2 and seem to be having an issue with the zaptel init script.. If I run.. #modprobe zaptel #modprobe wcfxo #modprobe wcfxs .. from a command line it load and appears to be working fine.. If I try and use the init script I get errors about ZT_CHANCONFIG and the modules don't see to laod up.. Anyone got any pointers? I am running Fedora Core

Hi, Im getting mad with this error, I have a x100p installed with wcfxo module loaded perfectly, I can receive incoming calls and detect very good the hangup for incoming calls. But for outgoing calls its a mess. When I place a call for outgoing, i heard the ringing, my cell or phone rings and when I pick up the phone it hangs: -- Called g1/91xxxxxxx -- Hungup