similar to: Whats Available NOW ??

Hi folks, this is specifically directed to Australia Asterisk users...... We are having a roblem with x100p 's when dialing STD. Upon receipt of the approximately the 5th (out of the ten) PIP's asterisk will hang up.... Now I am wondering if others are suffering the same problem ?? Any ideas ?? (it might exist on other cards, but so far I have only noticed the problem on x100p's).

*** Now you just need a "phone" or "station" (FXS) device and a method of connecting it. *** So... essentially I need to spend another $125 US on a Wildcard TDM400P so I can plug in an analog phone? On the X100P description it says: "The X100P supports FXS Loopstart and "Kewlstart" (Loopstart with far end disconnection supervision). It can detect ringing and

I am having a problem with Red Alarms on X100P cards. The most frustrating thing is I can not duplicate the alarms, therefore am not sure how to solve it. I have read after searching posts and the web that you can try different signaling methods which may help alleviate the problem. There is fxsks (Which I am currently using), fxsgs, and fxsls While reading the Digium site about these different

I have two grandstream budtetone-100 and cisco 7960g phones. When I talk via speaker phone on either of the phones I get a lot of echo. Any suggestions? Also how do I turn on the mark echo canceller. -----Original Message----- From: asterisk-users-admin@lists.digium.com [mailto:asterisk-users-admin@lists.digium.com] On Behalf Of asterisk-users-request@lists.digium.com Sent: Tuesday, April 13,

Hi, Would someone assist me with the configuration of my TMD10B and X100P cards? I would ask Digium but my support was good for only one install...( I had to rebuild my * box). I wrote down the configuration but I must have made a mistake somewhere. I have followed the instructions on the Digium site but I must be missing something. Here's the config (snippets) I've been attempting to

Hello fellow * users, I've been experimenting like a madman lately with asterisk, and I just love it. Just reading this list and asking a few questions here and there has helped me out a great amount. Not to mention the excellent resource we call the Wiki. I have searched for answers to the two following questions, but couldn't find anything, it is entirely possible i was just

I know the X100P cards are not supported by Digium any more, but for home office use, are they still acceptable? I have two POTS lines, one residential and one business line comming into the house. I'd like to get both into my * server and $15 total compared to > $100 for the newer TDMxxx card sure is desirable. Having said that, will the sound quality, functionality, stability, etc. be as

This is a system for our lab. I have no problem getting rid of X100P clones. But I am just curious why can they work. Even the drivers are not loading correctly. -----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of Kerry Garrison Sent: Tuesday, May 02, 2006 10:51 AM To: 'Asterisk Users Mailing List -

Hello folks, I'm very interested in the Digium/Asterisk combination but need some clarification. I would like to setup a SOHO for business and home use. Scenario One: I have one analog line, 4 analog telephones. Do I need a TDM400P + 4 FXS modules (Green) + X100P? Scenario Two: 2 analog lines, 1 selective ring number for fax, 8 analog phones. Is this what I need? 2 TDM400Ps and 8 FXS

Hi, I just got my TDM400P card (2 modules) and i installed it no probs. The card is detected fine, but for some reason when I add the card to zaptel.conf i get the following error: --snip-- ZT_CHANCONFIG failed on channel 2: Invalid argument (22) Did you forget that FXS interfaces are configured with FXO signalling and that FXO interfaces use FXS signalling? --snip-- My /etc/zaptel.conf looks

I get echo on my X100P for about 15 seconds then it disappears. Believe me, when I get a chance I'm going to tweak it since my wife nags me about it. I converted my house over to *. My setup: Compaq Deskpro EN SFF P3 500 Dual NIC for real IP and internal IP X100P Card for PSTN. Cisco ATA186 (two cordless phones for the old lady) Cisco 7960 Phone Cisco 2621 w/ 2 FXO's and 2 FXS (Fax is

The Asterisk Development Team has announced the releases of: DAHDI-Linux-v2.8.0 DAHDI-Tools-v2.8.0 dahdi-linux-complete-2.8.0+2.8.0 This release is available for immediate download at: http://downloads.asterisk.org/pub/telephony/dahdi-linux http://downloads.asterisk.org/pub/telephony/dahdi-tools http://downloads.asterisk.org/pub/telephony/dahdi-linux-complete In version 2.8 we have introduced

The Asterisk Development Team has announced the releases of: DAHDI-Linux-v2.8.0 DAHDI-Tools-v2.8.0 dahdi-linux-complete-2.8.0+2.8.0 This release is available for immediate download at: http://downloads.asterisk.org/pub/telephony/dahdi-linux http://downloads.asterisk.org/pub/telephony/dahdi-tools http://downloads.asterisk.org/pub/telephony/dahdi-linux-complete In version 2.8 we have introduced

The Asterisk Development Team has announced the releases of: DAHDI-Linux-v2.8.0-rc4 DAHDI-Tools-v2.8.0-rc4 dahdi-linux-complete-2.8.0-rc4+2.8.0-rc4 This release is available for immediate download at: http://downloads.asterisk.org/pub/telephony/dahdi-linux http://downloads.asterisk.org/pub/telephony/dahdi-tools http://downloads.asterisk.org/pub/telephony/dahdi-linux-complete *** THIS RC FIXES

The Asterisk Development Team has announced the releases of: DAHDI-Linux-v2.8.0-rc4 DAHDI-Tools-v2.8.0-rc4 dahdi-linux-complete-2.8.0-rc4+2.8.0-rc4 This release is available for immediate download at: http://downloads.asterisk.org/pub/telephony/dahdi-linux http://downloads.asterisk.org/pub/telephony/dahdi-tools http://downloads.asterisk.org/pub/telephony/dahdi-linux-complete *** THIS RC FIXES

hello, I just installed 2 brand new x100p cards into my linux system. Everything compliled and worked fine from the first try. Hoewver the phone lines I will use with this system have groundstart signaling. I have tried to change the zaptel.conf and zapata.conf to use this type of signaling but ztcfg gives me an error every time with the new configuration. Bellow are the config files and the

The Asterisk Development Team has announced the releases of: DAHDI-Linux-v2.8.0-rc2 DAHDI-Tools-v2.8.0-rc2 dahdi-linux-complete-2.8.0-rc2+2.8.0-rc2 This release is available for immediate download at: http://downloads.asterisk.org/pub/telephony/dahdi-linux http://downloads.asterisk.org/pub/telephony/dahdi-tools http://downloads.asterisk.org/pub/telephony/dahdi-linux-complete In version 2.8 we

The Asterisk Development Team has announced the releases of: DAHDI-Linux-v2.8.0-rc2 DAHDI-Tools-v2.8.0-rc2 dahdi-linux-complete-2.8.0-rc2+2.8.0-rc2 This release is available for immediate download at: http://downloads.asterisk.org/pub/telephony/dahdi-linux http://downloads.asterisk.org/pub/telephony/dahdi-tools http://downloads.asterisk.org/pub/telephony/dahdi-linux-complete In version 2.8 we

I am trying to find an example of how to set up my FXS Station Card in my Asterisk. I have (1) XP100P I have (1) tdm20B (2 Port FXS) Could someone tell me if this is correct? /etc/zaptel.conf fxsks=1 fxoks=2 fxoks=3 loadzone=us defaultzone=us /etc/asterisk/zapata.conf [channels] ; language=en ; ;X100P Port 1 context=inbound-analog signalling=fxs_ks usecallerid=yes echocancel=yes

Hello, I am having problems configuring a TDM400P 4 Port FXO card with groundstart signalling. The box has 2 X100P's, 1 TDM04B and 1 TDM40B. I can configure it for loopstart and it works, just not groundstart, which I need for this installation. What am I missing? Thanks! Mark /etc/zaptel.conf #two X100P FXO Cards # fxsls=1-2 # TDM400P 4 Port FXO (TDM04B) fxsgs=3-6 # TDM400P 4 Port