asterisk users - Jan 2005 - Need help configuring TDM10B / X100P Cards

Hi,

Would someone assist me with the configuration of my TMD10B and X100P cards? I
would ask Digium but my support was good for only one install...( I had to
rebuild my * box). I wrote down the configuration but I must have made a mistake
somewhere.  I have followed the instructions on the Digium site but I must be
missing something. Here's the config (snippets) I've been attempting to
use:

/etc/zaptel.conf 
fxsks=1 # X100P
fxoks=2-5 the FXS(green) module is closest to the bracket if you are looking at
the side of the card with all of the electronic components.
defaultzone=us
loadzone=us

/etc/asterisk/zapata.conf

echocancel=yes ; You can set this to 32, 64, or 128, tweak to your needs.
echocancelwhenbridged=yes
echotraining=400 ; Asterisk trains to the beginning of the call, number is in
milliseconds
callerid=asreceived
signalling=fxs_ks group=1
context=incoming ; Points to the incoming context of your extensions.conf 
channel => 1

signalling=fxo_ks
calleridgroup=2
context=default
channel=> 2-5

When I run ztcfg -v I get an error message which says ZT_CHANCONFIG failed on
channel 2: invalid argument. Did you forget that FXS interfaces are configured
with FXO signalling and that FXO interfaces use FXS signalling?

What am I doing wrong?

Thanks,

Mike
-------------- next part --------------
An HTML attachment was scrubbed...
URL:
http://lists.digium.com/pipermail/asterisk-users/attachments/20050122/0ec54aef/attachment.htm

Mike

How many modules on the TDM card?

When you mention the FXS(green module) I assume only one.

if so then fxoks=2-5 should be fxoks=2.

Regards

Dave
  -----Original Message-----
  From: asterisk-users-bounces@lists.digium.com
[mailto:asterisk-users-bounces@lists.digium.com]On Behalf Of Mike Chapman
  Sent: 22 January 2005 13:10
  To: 'Asterisk Users Mailing List - Non-Commercial Discussion'
  Subject: [Asterisk-Users] Need help configuring TDM10B / X100P Cards


  Hi,

  Would someone assist me with the configuration of my TMD10B and X100P
cards? I would ask Digium but my support was good for only one install...( I
had to rebuild my * box). I wrote down the configuration but I must have
made a mistake somewhere.  I have followed the instructions on the Digium
site but I must be missing something. Here's the config (snippets) I've
been
attempting to use:

  /etc/zaptel.conf
  fxsks=1 # X100P
  fxoks=2-5 the FXS(green) module is closest to the bracket if you are
looking at the side of the card with all of the electronic components.
  defaultzone=us
  loadzone=us

  /etc/asterisk/zapata.conf

  echocancel=yes ; You can set this to 32, 64, or 128, tweak to your needs.
  echocancelwhenbridged=yes
  echotraining=400 ; Asterisk trains to the beginning of the call, number is
in milliseconds
  callerid=asreceived
  signalling=fxs_ks group=1
  context=incoming ; Points to the incoming context of your extensions.conf
  channel => 1

  signalling=fxo_ks
  callerid  group=2
  context=default
  channel=> 2-5

  When I run ztcfg -v I get an error message which says ZT_CHANCONFIG failed
on channel 2: invalid argument. Did you forget that FXS interfaces are
configured with FXO signalling and that FXO interfaces use FXS signalling?

  What am I doing wrong?

  Thanks,

  Mike
-------------- next part --------------
An HTML attachment was scrubbed...
URL:
http://lists.digium.com/pipermail/asterisk-users/attachments/20050122/470788cc/attachment.htm