search for: tdm10b

Ok. I just got a TDM10B and it is in with my X100P. So as it says in the provided instructions, I used the command modprobe tor2 I get an error message saying that there is no such device. My zaptel.conf looks like this: fxsks=1 fxoks=2 So I load the X100P first. (modprobe wcfxo) Then I load the TDM10B (modprobe tor2...

Is this supported? I have a very simple setup where I have 2 X100P cards and a TDM10B. The TDM10B is connected to a phone that has a digital answering machine built into it. If I make an inbound call on either X100P interface it gets transferred to the TDM10B interface. If I let it ring the TDM10B interface answers the call and the greeting message of the answering machine start...

I've been having trouble with a TDM10B that I installed a few days ago. At first I could not modprobe it at all (getting the errors below). I switched the X100P that was also installed (with a Motorola chip) with one with a Tiger-something chip, and then everything starts up okay. However, after a few hours, the FXS port dies (no bat...

I got the devkit tdm400P(tdm10b) + x100p bundle. Where does one buy more ports for the tdm400p? I couldnt find anywhere on digium site or resellers to buy them? -Dan

So I have an X100P, and a TDM10B both working (at least I think they are). The drivers have been loaded and ztcfg -vv shows no errors in the configuration of two channels. When I run asterisk -vvvc and pick up my phone (plugged into TDM10B), I don't gear a dialtone. in phone.conf, I have [interfaces] mode=dialtone format=s...

Is there anything special needed to load up a TDM10B card?? I got the card today.. Took it from the box, put it into a PCI slot.. connected the power to the card and booted the PC.. I have removed the X100P to avoid confusion and I have the following in the config files.. in /etc/zaptel.conf # For the X100P #fxsks=1 # For the TDM10B fxoks=1 in...

Hi, Would someone assist me with the configuration of my TMD10B and X100P cards? I would ask Digium but my support was good for only one install...( I had to rebuild my * box). I wrote down the configuration but I must have made a mistake somewhere. I have followed the instructions on the Digium site but I must be missing something. Here's the config (snippets) I've been attempting to

Ok. I am confused. I now have conflicting answers to my question: Do you need to use a special phone to use SIP? My setup is X100P and TDM10B. I would like to connect to iConnectHere, which uses SIP. Has anybody done this before (using similar equipment to what I have listed above)? And if it is not possible, could somebody please explain why. I don't understand why this wouldn't work. ----[Extra Information]--------------...

Hi. Today I was asked about a function of asterisk. That's what it should to: a call arrives -> put it in a queue -> remain here ;) Then, when someone wants to answer, just dial an extension and the older call that's in the queue is picked up. A sort of app_queueonly + app_pickolderqueuecall . As far as I know asterisk doesn't support that, so was wondering if someone

...k and this wonderful world of convergence. From reading the docs, list and websites I hopefully correctly understand that I can use a plain cheap isdn4linux supported ISDN (passive) TA to hook up the PC to the ISDN line from the telco (FXO card?). Next in the PC I also need a FXS card like a Digium TDM10B or PhoneJack so I can hook up an analog phone to it. In sort of graphics: analog phone === FXS card - PC - FXO card === Telco/PSTN PhoneJack ISDN TA ISDN Digium TDM10B Questions: 1) Is my description above right? 2) Is there a FXS card to which I can...

I have an X100p card....and it is hard to hear the person on the other end. Should I mess with these values? I have heard both yes and no to this question in the past. If yes, how much louder should I make them? Thanks, MIchael

...nsfer=yes cancallforward=yes callreturn=yes echocancel=yes echocancelwhenbridged=yes rxgain=-100.0 txgain=-50.0 callgroup=1 pickupgroup=1 immediate=no musiconhold=default signalling=fxs_ks context=incoming group=1 channel=1-2 ;X100P signalling=fxo_ks context=outgoing group=2 channel=3-4 ;TDM10B --------------------------------------------------------------------------------------------------------------- the ztcfg -vv command does not return an error, but there is an error registering channels 3 and 4 when I try to start asterisk. I have had everything working if I define my channels a...

Hi, I'm still struggling to make netmeeting work with asterisk and oh323. I'm dialing from netmeeting into a regular phone, connected to my TDM10B. everything looks great, except that I cannot hear my voice at the FXS side, just static that increases when I speak on netmeeting's mike. Nevertheless, if I speak on the telephone I do can hear my voice on my headsets. I configured netmeeting for CCITT u-Law, 8 Khz, 8 bit mono. On asterisk...

Hello Everyone, I just got my Dev Kit TDM today... :D I installed the X100P ok (wcfxo); however, when I tried to 'modprobe wcfxs' for the TDM400P(TDM10B), I got this error message: /lib/modules/2.4.19/misc/wcfxs.o: init_module: No such device Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters /lib/modules/2.4.19/misc/wcfxs.o: insmod /lib/modules/2.4.19/misc/wcfxs.o failed /lib/modules/2.4.19/m...

Hi All... I have a maddening problem... I have Asterisk configured to pick up a line after 4 rings. I do this to allow my fax machine to pick up a particular distinctive ring pattern, so I don't have to pay for a dedicated fax line. If someone calls the line, lets it ring 3 times and then hangs up, Asterisk answers the line, and holds it off hook forever, constantly playing the

In having configured my first * server there are a few questions I could not understand or find answers to 1) How does one use ztmonitor to adjust the rxgain and txgain. I have set mine to -1.0 each to get rid of echo on std phones connected on the TDM10B FXS module 2) Is it best to use a TDM card with an TFX and FXO module or is the the FXO = X100p and FXS on TDM a good method? 3) How do I disable mgcp, skinny etc that I will not be using ? Asterisk loads / scrolls a lot when you start it. 4) How do I calculate/assess the Load * is placing on...

Hi all, -------- I have installed a TDM400 with one active FXS port (TDM10B) an connected it to a Siemens Euroset 2015 analogue phone. I have installed some smom IP phones to the network as well and configured them as usual (sip.conf). For configuring the TDM10B I have used FXO signalling in /etc/zaptel.conf and in /etc/asterisk/zapata.conf. I definded the TDM channel and...

...to a structured phone system. It *looks* like I can go the route of the Cisco Analog -> VOIP for about $100 on ebay. That will get me two analog devices on the system. If I have four analog devices (2 normal phones, 1 fax and one 4 phone cordless system) is this the best setup? Do I need the TDM10B with the Asterisk TDM Dev Kit or does that just let me do one analog phone into the system? When converting from analog to VOIP do I get all the same features that I would if I got a TDM400P (4 ports of analog devices)? As I said I'm new and I would LOVE any pointers, HOWTOs or any good ad...

I'm having with an echo or delay I connect to the PSTN with a x100p and then connect a std. phone to a FXS module on a TDM10B. The std phone is only 2-wire so I know this is not helping. (yes I have read the 2-wire 4-wire issue) I have tried many echocancel values. The best thing to help was rxgain and txgain. below is my current zapata.conf file All help would be grateful. I have tried and tried for 2 weeks it is rath...

...eveloping an application in which I need asterisk to pass on an incoming call to a separate IVR server. The problem is that asterisk appears to hang up while the IVR is playing back a sequence of recorded voice and systhesized voice prompts. My setup is: Analog line ->X100P->asterisk->TDM10B- >phone cord->Dialogic analog port->IVR system. Asterisk should dial the IVR system, which should answer and play back its IVR scenario script to the caller. However, when a call comes in, asterisk answers on Zap1-1 and dials Zap2-1. The IVR system answers the call and begins to play...