Does anyone have any experience getting a Mitel SX-200 EL/ML PBX system to work with *? I'm not getting inbound or outbound calls to work. (Inbound caller gets line busy tone.) SETTINGS FROM MITEL: I built a Crossover cable and connected it like this: PSTN--T1--ASTRISK--T1--OLD MITEL -Crossover Cable Pin-out: 1 - 4 2 - 5 4 - 1 5 - 2 Mitel Settings: Line Coding = B8ZS Framing = D4 (T1 Card 9109-021-001-NA) (My config: span=1,1,0,d4,b8zs & e&m=1-24) The card is a 24 channel T1 - not a PRI right? (T1 E&M Emulation Trunk: 1) So does that mean I use E&M with Winkstart? (signalling=em_w) (is this spelt right?) (Wink setting is an assumption based upon a setting I saw in the PBX called wink timer) Using a Sangoma A104D: zttool -GAVE "OK" on PSTN -Gave "RED" on MITEL Timing -Receiving Time from PSTN & Giving to the Mitel What debugging can I do to get more information? -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20080304/f6eb64f1/attachment.htm
I would strongly recommend ESF/B8ZS. If you have a RED alarm that means the device does not see a line connected to it -- check cabling. Mark Best wrote:> Does anyone have any experience getting a Mitel SX-200 EL/ML PBX system > to work with *? > > I'm not getting inbound or outbound calls to work. (Inbound caller gets > line busy tone.) > > > > SETTINGS FROM MITEL: > > I built a Crossover cable and connected it like this: > > PSTN--T1--ASTRISK--T1--OLD MITEL > > -Crossover Cable Pin-out: > > 1 - 4 > > 2 - 5 > > 4 - 1 > > 5 - 2 > > Mitel Settings: > > Line Coding = B8ZS Framing = D4 (T1 Card 9109-021-001-NA) > > (My config: span=1,1,0,d4,b8zs & e&m=1-24) > > > > The card is a 24 channel T1 - not a PRI right? (T1 E&M Emulation Trunk: > 1) > > So does that mean I use E&M with Winkstart? > > (signalling=em_w) (is this spelt right?) > > (Wink setting is an assumption based upon a setting I saw in > the PBX called wink timer) > > > > Using a Sangoma A104D: > > zttool > > -GAVE "OK" on PSTN > > -Gave "RED" on MITEL > > Timing > > -Receiving Time from PSTN & Giving to the Mitel > > > > What debugging can I do to get more information? > > > > > ------------------------------------------------------------------------ > > _______________________________________________ > -- Bandwidth and Colocation Provided by http://www.api-digital.com -- > > asterisk-users mailing list > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-users-- Consulting for Asterisk, Polycom, Sangoma, Digium, Cisco, LAN, WAN, QoS, T-1, PRI, Frame Relay, Linux, and network design. Based near Birmingham, AL. Now accepting clients worldwide.
Eric, Looks like my Mitel does support ESF; I'll try changing it. One question before I do. If I change it right now, do you suppose my Telco automatically adapt? TELCO---T1---MITEL -----Original Message----- From: asterisk-users-bounces at lists.digium.com [mailto:asterisk-users-bounces at lists.digium.com] On Behalf Of Eric Wieling Sent: Tuesday, March 04, 2008 12:58 PM To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re: [asterisk-users] Mitel SX-200 + * I would strongly recommend ESF/B8ZS. If you have a RED alarm that means the device does not see a line connected to it -- check cabling. Mark Best wrote:> Does anyone have any experience getting a Mitel SX-200 EL/ML PBXsystem> to work with *? > > I'm not getting inbound or outbound calls to work. (Inbound callergets> line busy tone.) > > > > SETTINGS FROM MITEL: > > I built a Crossover cable and connected it like this: > > PSTN--T1--ASTRISK--T1--OLD MITEL > > -Crossover Cable Pin-out: > > 1 - 4 > > 2 - 5 > > 4 - 1 > > 5 - 2 > > Mitel Settings: > > Line Coding = B8ZS Framing = D4 (T1 Card 9109-021-001-NA) > > (My config: span=1,1,0,d4,b8zs & e&m=1-24) > > > > The card is a 24 channel T1 - not a PRI right? (T1 E&M EmulationTrunk:> 1) > > So does that mean I use E&M with Winkstart? > > (signalling=em_w) (is this spelt right?) > > (Wink setting is an assumption based upon a setting I sawin> the PBX called wink timer) > > > > Using a Sangoma A104D: > > zttool > > -GAVE "OK" on PSTN > > -Gave "RED" on MITEL > > Timing > > -Receiving Time from PSTN & Giving to theMitel> > > > What debugging can I do to get more information? > > > > >------------------------------------------------------------------------> > _______________________________________________ > -- Bandwidth and Colocation Provided by http://www.api-digital.com -- > > asterisk-users mailing list > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-users-- Consulting for Asterisk, Polycom, Sangoma, Digium, Cisco, LAN, WAN, QoS, T-1, PRI, Frame Relay, Linux, and network design. Based near Birmingham, AL. Now accepting clients worldwide. _______________________________________________ -- Bandwidth and Colocation Provided by http://www.api-digital.com -- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
On Tue, 2008-03-04 at 12:34 -0800, Mark Best wrote:> Does anyone have any experience getting a Mitel SX-200 EL/ML PBX > system to work with *?No, but I'll make a few comments anyway. I'm not sure if they'll help you at all, but maybe it'll help explain a few things to someone else on the list.> I?m not getting inbound or outbound calls to work. (Inbound caller > gets line busy tone.)Is the T1 in alarm? You've first gotta get it out of alarm before you can make calls on it. Alarms are usually caused by physical connectivity problems, or problems with framing and/or linecoding.> Mitel Settings: > > Line Coding = B8ZS Framing = D4 (T1 Card 9109-021-001-NA)Hmmmn... D4 and B8ZS together? That's bizarre. Usually people will use D4 framing and AMI linecoding together, or ESF framing and B8ZS linecoding. I've never seen anyone uuse B8ZS linecoding with D4 framing. -- Jared Smith Community Relations Manager Digium, Inc.
Jared, Thanks for the help. There are other T1 trunks (using AMI,D4) going to different departments; however the trunk line talking to the Telco is what it is. I do have the ability to change it to ESF, so I will try changing it - do you suppose my Telco will automaticly adapt if I do? (I'm fairly confident they support ESF.) -----Original Message----- From: asterisk-users-bounces at lists.digium.com [mailto:asterisk-users-bounces at lists.digium.com] On Behalf Of Jared Smith Sent: Tuesday, March 04, 2008 1:08 PM To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re: [asterisk-users] Mitel SX-200 + * On Tue, 2008-03-04 at 12:34 -0800, Mark Best wrote:> Does anyone have any experience getting a Mitel SX-200 EL/ML PBX > system to work with *?No, but I'll make a few comments anyway. I'm not sure if they'll help you at all, but maybe it'll help explain a few things to someone else on the list.> I'm not getting inbound or outbound calls to work. (Inbound caller > gets line busy tone.)Is the T1 in alarm? You've first gotta get it out of alarm before you can make calls on it. Alarms are usually caused by physical connectivity problems, or problems with framing and/or linecoding.> Mitel Settings: > > Line Coding = B8ZS Framing = D4 (T1 Card 9109-021-001-NA)Hmmmn... D4 and B8ZS together? That's bizarre. Usually people will use D4 framing and AMI linecoding together, or ESF framing and B8ZS linecoding. I've never seen anyone uuse B8ZS linecoding with D4 framing. -- Jared Smith Community Relations Manager Digium, Inc. _______________________________________________ -- Bandwidth and Colocation Provided by http://www.api-digital.com -- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
Seemingly Similar Threads
- TE11OP -> Mitel 200Sx??
- Asterisk and Mitel SX 200 Slip and Frame Err ors causing Major Ala rms
- Asterisk and Mitel SX 200 Slip and Frame Errors causing Major Ala rms
- Help to connect to Mitel PBX via a T1 connection and a T100p
- X100P and Mitel SX-2000 Light