search for: cas

Dear members of the list, I have difficulties to obtain sync with a Digium TE420 PCI Express For four entries E1, In my case I am with only 3 E1s available to configure. The telephony operator is BrasilTelecom and Signaling is R2 Digital. The information I have is that are E1s with 32 channels, not have sure. My settings Have been based on the link reference: Http://www.voip-info.org/wiki/view/Asterisk + MFC + R2...

def cas casses = [@cas.ss,@cas.s,@cas.xl,@cas.l,@cas.m,@cas.w,@cas.xw] casses.each do |cas| if cas >= 10 @user.send(cas) -= 1 @user.save! end end my error: app/controllers/battle_controller.rb:383: parse error, unexpected tOP_ASGN, expecting kEND @user.send(cas) -= 1 ^ app/controller...

Hello All I'm using asterisk 1.1.X and MFCR2 lib version 0.03pre2. when i call to E1 (connected with asterisk), chan_unicall don't detected event incoming call and show error. error messages: *CLI> Warning, flexibel rate not heavily tested! Rx CAS bits 0x9 [ 10000/ 0/ 0] Line unblocked -- R2 Channel 4 unblocked Rx CAS bits 0x9 [ 10000/ 0/ 0] Line unblocked -- R2 Channel 2 unblocked Rx CAS bits 0x9 [ 10000/ 0/ 0] Line unblocked -- R2 Channel 13 unblocked Rx CAS bits 0x1 [ 1/ 0/ 0] Tx CAS bits 0xD [...

...= NO TDMV_SPAN = 1 TDMV_DCHAN = 0 [w1g1] ACTIVE_CH = ALL TDMV_ECHO_OFF = NO I start wanrouter, the card connected success, monitor on E10 exchange (ACATEL), the status of all channels are LIBR. when i dial to asterisk, error show as belows *CLI> Warning, flexibel rate not heavily tested! Rx CAS bits 0x9 [ 10000/ 0/ 0] Line unblocked -- R2 Channel 4 unblocked Rx CAS bits 0x9 [ 10000/ 0/ 0] Line unblocked -- R2 Channel 2 unblocked Rx CAS bits 0x9 [ 10000/ 0/ 0] Line unblocked -- R2 Channel 13 unblocked Rx CAS bits 0x1 [ 1/ 0/ 0] Tx CAS bits 0xD [...

Hi CAS is a centralized authentication service, and the cas_auth filter can be installed to automatically make your web application authenticate against a CAS server. The SVN path to the plugin is http://svn.ki.se/rails/plugins/cas_auth and a homepage with some information can be found at http://o...

...TE110P T1/E1 [42949386.000000] ACPI: PCI Interrupt 0000:01:08.0[A] -> GSI 20 (level, low) -> IRQ 217 [42949386.020000] e100: eth0: e100_probe: addr 0xff8fe000, irq 217, MAC addr 00:0C:F1:E7:1B:0B [42949386.060000] Registered tone zone 20 (Brazil) [42949386.060000] TE110P: Span configured for CAS/HDB3 [42949386.060000] Calling startup (flags is 4099) [42949386.100000] CSLIP: code copyright 1989 Regents of the University of California [42949386.130000] ISDN subsystem Rev: 1.1.2.3/1.1.2.3/1.1.2.2/1.1.2.3/1.1.2.2/1.1.2.2 loaded [42949386.190000] HiSax: Linux Driver for passive ISDN cards [4294...

...Asterisk version: 1.2.9.1 Zaptel version: 1.2.6 Unicall: unicall-0.0.3pre9 Board: ATCOM AX-4E (same as Tormenta2) asterisk-test:/# cat /proc/interrupts CPU0 0: 277514 IO-APIC-edge timer 1: 2 IO-APIC-edge keyboard 2: 0 XT-PIC cascade 8: 4 IO-APIC-edge rtc 14: 38259 IO-APIC-edge ide0 15: 12 IO-APIC-edge ide1 16: 0 IO-APIC-level usb-uhci, usb-uhci 17: 0 IO-APIC-level Intel ICH5 18: 0 IO-APIC-level usb-uhci 19: 0 IO-APIC-level usb-uhci 2...

I create domain in Samba AD DC and add user 'cas' and group 'aaa': # samba-tool user list | grep cas cas # samba-tool group list | grep aaa aaa Now I try to add user 'cas' to group 'aaa': # samba-tool group addmembers aaa cas -Uadministrator Added members to group aaa But listmembers does not show this user i...

...=both loglevel=255 protocolclass=mfcr2 protocolvariant=br,20,4 protocolend=cpe group=1 callgroup=1 channel => 1-15 channel => 17-31 channel => 32-46 channel => 48-62 channel => 63-77 channel => 94-108 channel => 110-124 * zaptel.conf * loadzone=br defaultzone=br span=1,1,0,cas,hdb3 cas=1-15:1101 cas=17-31:1101 span=2,0,0,cas,hdb3 cas=32-46:1101 cas=48-62:1101 span=3,0,0,cas,hdb3 cas=63-77:1101 cas=79-93:1101 span=4,0,0,cas,hdb3 cas=94-108:1101 cas=110-124:1101 * lor error * -- Executing Dial("SIP/1000-1de2", "Unicall/g1/40020022|40|Ttr") i...

...ly receive messages Aug 4 11:54:07 WARNING[9402]: chan_unicall.c:2865 handle_uc_event: Unicall/14 event Protocol failure for each one of the 30 (31?) channels. I send you my configs and important command outputs: My zaptel.conf ------------------- # MFC/R2 does not normally use CRC4 span=1,1,0,cas,hdb3 cas=1-15:1101 cas=17-31:1101 loadzone=mx defaultzone=us ------------------- My unicall.conf ------------------- [channels] context=incoming usecallerid=yes hidecallerid=no callwaitingcallerid=yes threewaycalling=yes transfer=yes cancallforward=yes callreturn=yes echocancel=yes echocancelwhenb...

...ar combinations of a and b (let's say Low for a=0 & b=0, Medium for a=10 & b=50, High for a=50 & b=200, others levels set to NA), reading them from a data-frame which describes the desired subset and corresponding levels. Here's my own solution (inputs are data-frames df and cas, output is the sub factor): > cas <- as.data.frame(matrix(c(0, 10,50, 0, 50, 200), 3, 2,dimnames=list(c("Low", "Medium", "High"), c("a", "b")))) > cas a b Low 0 0 Medium 10 50 High 50 200 > sub <- character(l...

Dear all I would like to aggregate a data frame in a three minute interval. I have a time vector: > str(cas.param) `POSIXct', format: chr [1:181] "2003-06-12 09:00:00" "2003-06-12 09:01:00" "2003-06-12 09:02:00" and I want to turn it into a factor by cut. It works if I want to break it in let say hours > str(cut(cas.param,breaks="hour")) Factor w/ 3 le...

Hi, I try to find some information about CAS E1 signalling and how it's handled by Asterisk. My customer wants to connect to a BT ITS Netrix by CAS E1 E&M. The system is intended to take the channels and mix them (meetme / confbridge) and send the audio back mixed to each. The layout: BT ITS Netrix: CAS E1 E&M <-> MUX -...

I am having a problem trying to get a Sangoma A101 to work with Unicall. I have installed the sangoma drivers and everything seems to be well but when I try to run ztcfg I get the following error: CAS signalling on span 1 conflicts with HDLC with FCS check on channel 16. Here is my /etc/zaptel.conf # MFC/R2 normalmente no usa CRC4 span=1,0,0,cas,hdb3 cas=1-15:1101 dchan=16 cas=17-31:1101 This configuration works with Digium cards. Here is the wanpipe1.conf file: [devices] wanpipe1 = WAN_A...

Hi, It seems like my ATA is making a ringing noise... (as it used to), but now (After the upgrade from 1.0.7 to 1.2) asterisk also is either making the ringing, or passing the PRI ringing from the telco on to me. Any suggestions on how to fix this?

On 2/21/08, Torvald Riegel <torvald at se.inf.tu-dresden.de> wrote: > why is the intrinsic name not CAS? And having another version that returns > just a bool might be better in some cases ( 1. does CAS return the value on > all architectures? 2. you can just jump based on a flag and don't need to > compare it again). Just my 2 cents though ... I was going from chandler's docs,...

According to CarrierAccess, the Adit 600 uses CAS for voice signalling. What is this? This should not be a problem for Asterisk? Does the Asterisk server need to reencode CAS into aLaw when going to Euro ISDN? BR Daniel Nystr?m

Hi. I am in the Brazil. I have a problem on Unicall for Asterisk 1.4. I am working with E1 with 30 channels. Message when it receives calls: chan_unicall.c:2603 handle_uc_event:unicall/1 protocol error.cause 32772. My files: /etc/zaptel.conf: span=1,1,0,cas,hdb3 cas=1-15:1101 cas=17-31:1101 loadzone = br defaultzone = br fxoks = 32-55 /etc/asterisk/unicall.conf: [Channels] language=br context=default usecallerid=yes hidecallerid=no callwaitingcallerid=yes threewaycalling=yes transfer=yes cancallforward=yes callreturn=yes echocancel=yes echocancelwhe...