Hi all,
On my Suse 9.3 prof. server I had two NIC’s:
Eth0 IP 192.168.1.1
Eth1 IP 192.168.2.1
Now I added new NIC (eth2)
Eth0 IP 192.168.1.1
Eth1 IP 192.168.2.1
Eth2 IP 192.168.1.2
Now I erased eth0 config and turned off this NIC in motherboard bios
Eth1 IP 192.168.2.1
Eth2 IP 192.168.1.2
I renamed eth2 to eth0
Eth1 IP 192.168.2.1
Eth0 IP 192.168.1.2
And, finally I changed IP of eth0
Eth1 IP 192.168.2.1
Eth0 IP 192.168.1.1
So, now I have same setup as I had before but with new NIC at place.
Swat is working as it should, but when I press “status” button in swat, smbd
and nmbd are shown as not started, but my samba works well. Anyway, in
/var/log/samba/log.swat when I press “status” button I have:
[2006/03/29 08:34:16, 2] lib/util_sock.c:open_socket_out(789)
error connecting to 192.168.1.2:445 (No route to host)
[2006/03/29 08:34:19, 2] lib/util_sock.c:open_socket_out(789)
error connecting to 192.168.1.2:139 (No route to host)
[2006/03/29 08:34:19, 1] libsmb/cliconnect.c:cli_connect(1326)
Error connecting to 192.168.1.2 (No route to host)
[2006/03/29 08:34:22, 2] lib/util_sock.c:open_socket_out(789)
error connecting to 192.168.1.2:445 (No route to host)
[2006/03/29 08:34:25, 2] lib/util_sock.c:open_socket_out(789)
error connecting to 192.168.1.2:139 (No route to host)
[2006/03/29 08:34:25, 1] libsmb/cliconnect.c:cli_connect(1326)
Error connecting to 192.168.1.2 (No route to host)
[2006/03/29 08:34:25, 0] libsmb/nmblib.c:send_udp(790)
Packet send failed to 192.168.1.2(137) ERRNO=Invalid argument
[2006/03/29 08:34:25, 0] libsmb/nmblib.c:send_udp(790)
Packet send failed to 192.168.1.2(137) ERRNO=Invalid argument
As you can see, swat is somehow using IP 192.168.1.2 that is not in use now,
instead of 192.168.1.1 of 192.168.2.1.
server:/var/log/samba # ifconfig
eth0 Link encap:Ethernet HWaddr 00:11:95:5F:F2:6F
inet addr:192.168.1.1 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::211:95ff:fe5f:f26f/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:649842 errors:0 dropped:0 overruns:0 frame:0
TX packets:771539 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:153367849 (146.2 Mb) TX bytes:431793577 (411.7 Mb)
Interrupt:185 Base address:0x4000
eth1 Link encap:Ethernet HWaddr 00:11:95:5F:F2:72
inet addr:192.168.2.1 Bcast:192.168.2.255 Mask:255.255.255.0
inet6 addr: fe80::211:95ff:fe5f:f272/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:5168465 errors:0 dropped:0 overruns:0 frame:0
TX packets:6542625 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:961455736 (916.9 Mb) TX bytes:5116440423 (4879.4 Mb)
Interrupt:217 Base address:0x6000
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:225478 errors:0 dropped:0 overruns:0 frame:0
TX packets:225478 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:75038623 (71.5 Mb) TX bytes:75038623 (71.5 Mb)
server:/var/log/samba # route
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use
Iface
192.168.2.0 * 255.255.255.0 U 0 0 0 eth1
192.168.1.0 * 255.255.255.0 U 0 0 0 eth0
loopback * 255.0.0.0 U 0 0 0 lo
server:/var/log/samba #
I can’t figure out where this 192.168.1.2 is written?
Zoran
