wolle321 at freenet.de
2018-Sep-07 20:11 UTC
[Nouveau] Strange monitor behavior on forced DVI-D output
Hello , I'm new here but I hope I can describe my problem exactly. I'm trying to get my DVI-Monitor to work with nouveau. The monitor is automatically reported as not connected. LVDS is detected. Forcing it on Xorg.conf didn't work, KMS does: video=DVI-D-1:1920x1200e video=LVDS-1:d X started with 1024x768, but could switch by xrandr to 1920x1200. The viewed picture now is 1920x1200 , but the Monitor runs on 960x1200, so that it looks very pixelated. (But there is no panning) Tried to add another (cvt calculated) modeline (1920x1200_60.00) with xrandr, but didnt help: Screen 0: minimum 320 x 200, current 1920 x 1200, maximum 8192 x 8192 LVDS-1 disconnected (normal left inverted right x axis y axis) DVI-D-1 connected 1920x1200+0+0 (normal left inverted right x axis y axis) 0mm x 0mm 1920x1200 60.00 1024x768 60.00 800x600 60.32 56.25 848x480 60.00 640x480 59.94 1920x1200_60.00 59.88* dmesg: ... [ 1.526099] fb: switching to nouveaufb from VESA VGA [ 1.526125] Console: switching to colour dummy device 80x25 [ 1.526265] scsi host0: ahci [ 1.526284] nouveau 0000:01:00.0: NVIDIA G92 (092f00a2) [ 1.531073] scsi host1: ahci [ 1.535016] scsi host2: ahci [ 1.541021] scsi host3: ahci [ 1.548031] scsi host4: ahci [ 1.553014] scsi host5: ahci [ 1.553064] ata1: SATA max UDMA/133 abar m2048 at 0xdb325000 port 0xdb325100 irq 29 [ 1.553067] ata2: SATA max UDMA/133 abar m2048 at 0xdb325000 port 0xdb325180 irq 29 [ 1.553068] ata3: DUMMY [ 1.553070] ata4: DUMMY [ 1.553073] ata5: SATA max UDMA/133 abar m2048 at 0xdb325000 port 0xdb325300 irq 29 [ 1.553076] ata6: SATA max UDMA/133 abar m2048 at 0xdb325000 port 0xdb325380 irq 29 [ 1.553513] e1000e 0000:00:19.0: Interrupt Throttling Rate (ints/sec) set to dynamic conservative mode [ 1.590043] firewire_ohci 0000:86:06.0: added OHCI v1.10 device as card 0, 4 IR + 4 IT contexts, quirks 0x11 [ 1.678230] nouveau 0000:01:00.0: bios: version 62.92.6e.00.10 [ 1.678547] nouveau 0000:01:00.0: mxm: BIOS version 2.0 [ 1.680769] nouveau 0000:01:00.0: mxm: unmatched output device 0103010201010100 [ 1.701487] nouveau 0000:01:00.0: fb: 1024 MiB GDDR3 [ 1.711344] e1000e 0000:00:19.0 eth0: (PCI Express:2.5GT/s:Width x1) 00:24:81:62:88:f7 [ 1.711351] e1000e 0000:00:19.0 eth0: Intel(R) PRO/1000 Network Connection [ 1.711374] e1000e 0000:00:19.0 eth0: MAC: 7, PHY: 8, PBA No: 1052FF-0FF [ 1.712279] e1000e 0000:00:19.0 enp0s25: renamed from eth0 [ 1.775146] [TTM] Zone kernel: Available graphics memory: 4066038 kiB [ 1.775148] [TTM] Zone dma32: Available graphics memory: 2097152 kiB [ 1.775150] [TTM] Initializing pool allocator [ 1.775159] [TTM] Initializing DMA pool allocator [ 1.775171] nouveau 0000:01:00.0: DRM: VRAM: 1024 MiB [ 1.775173] nouveau 0000:01:00.0: DRM: GART: 1048576 MiB [ 1.775177] nouveau 0000:01:00.0: DRM: TMDS table version 2.0 [ 1.775179] nouveau 0000:01:00.0: DRM: DCB version 4.0 [ 1.775182] nouveau 0000:01:00.0: DRM: DCB outp 00: 01000323 00010034 [ 1.775185] nouveau 0000:01:00.0: DRM: DCB outp 01: 02011312 00020030 [ 1.775187] nouveau 0000:01:00.0: DRM: DCB outp 02: 02022312 00020020 [ 1.775190] nouveau 0000:01:00.0: DRM: DCB outp 05: 02034300 00000028 [ 1.775192] nouveau 0000:01:00.0: DRM: DCB conn 00: 00000040 [ 1.775194] nouveau 0000:01:00.0: DRM: DCB conn 01: 00001131 [ 1.775196] nouveau 0000:01:00.0: DRM: DCB conn 02: 00002231 [ 1.775198] nouveau 0000:01:00.0: DRM: DCB conn 03: 00110346 [ 1.775200] nouveau 0000:01:00.0: DRM: DCB conn 04: 00000400 [ 1.775202] nouveau 0000:01:00.0: DRM: DCB conn 05: 00000510 [ 1.775203] nouveau 0000:01:00.0: DRM: DCB conn 06: 00000511 [ 1.775205] nouveau 0000:01:00.0: DRM: DCB conn 07: 00000513 [ 1.775207] nouveau 0000:01:00.0: DRM: DCB conn 08: 00002631 [ 1.775209] nouveau 0000:01:00.0: DRM: DCB conn 09: 00001731 [ 1.775211] nouveau 0000:01:00.0: DRM: DCB conn 10: 00002831 [ 1.775213] nouveau 0000:01:00.0: DRM: DCB conn 11: 00110946 [ 1.775215] nouveau 0000:01:00.0: DRM: DCB conn 12: 00000a00 [ 1.775217] nouveau 0000:01:00.0: DRM: DCB conn 13: 00000b10 [ 1.775219] nouveau 0000:01:00.0: DRM: DCB conn 14: 00000b11 [ 1.775221] nouveau 0000:01:00.0: DRM: DCB conn 15: 00000b13 [ 1.776874] [drm] forcing LVDS-1 connector off [ 1.776924] [drm] forcing DVI-D-1 connector on [ 1.777030] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). [ 1.777031] [drm] Driver supports precise vblank timestamp query. [ 1.779020] nouveau 0000:01:00.0: DRM: MM: using CRYPT for buffer copies [ 1.791526] nouveau 0000:01:00.0: DRM: allocated 1920x1200 fb: 0x70000, bo (ptrval) [ 1.792143] fbcon: nouveaufb (fb0) is primary device [ 1.792399] Console: switching to colour frame buffer device 240x75 [ 1.792449] nouveau 0000:01:00.0: fb0: nouveaufb frame buffer device [ 1.794020] usb 3-1: new full-speed USB device number 2 using uhci_hcd [ 1.797047] [drm] Initialized nouveau 1.3.1 20120801 for 0000:01:00.0 on minor 0 ... [ 37.435414] nouveau 0000:01:00.0: Direct firmware load for nouveau/nv84_xuc00f failed with error -2 [ 37.435418] nouveau 0000:01:00.0: vp: unable to load firmware nouveau/nv84_xuc00f [ 37.435420] nouveau 0000:01:00.0: vp: init failed, -2 Xorg.0.log: ... [ 7.646] (==) Matched nouveau as autoconfigured driver 0 [ 7.646] (==) Matched nouveau as autoconfigured driver 1 [ 7.646] (==) Matched modesetting as autoconfigured driver 2 [ 7.646] (==) Matched fbdev as autoconfigured driver 3 [ 7.646] (==) Matched vesa as autoconfigured driver 4 [ 7.646] (==) Assigned the driver to the xf86ConfigLayout [ 7.646] (II) LoadModule: "nouveau" [ 7.648] (II) Loading /usr/lib/xorg/modules/drivers/nouveau_drv.so [ 7.649] (II) Module nouveau: vendor="X.Org Foundation" [ 7.649] compiled for 1.19.3, module version = 1.0.15 [ 7.649] Module class: X.Org Video Driver [ 7.649] ABI class: X.Org Video Driver, version 23.0 [ 7.649] (II) LoadModule: "modesetting" [ 7.650] (II) Loading /usr/lib/xorg/modules/drivers/modesetting_drv.so [ 7.650] (II) Module modesetting: vendor="X.Org Foundation" [ 7.650] compiled for 1.19.6, module version = 1.19.6 [ 7.650] Module class: X.Org Video Driver [ 7.650] ABI class: X.Org Video Driver, version 23.0 [ 7.650] (II) LoadModule: "fbdev" [ 7.650] (II) Loading /usr/lib/xorg/modules/drivers/fbdev_drv.so [ 7.650] (II) Module fbdev: vendor="X.Org Foundation" [ 7.650] compiled for 1.19.3, module version = 0.4.4 [ 7.650] Module class: X.Org Video Driver [ 7.650] ABI class: X.Org Video Driver, version 23.0 [ 7.650] (II) LoadModule: "vesa" [ 7.650] (II) Loading /usr/lib/xorg/modules/drivers/vesa_drv.so [ 7.650] (II) Module vesa: vendor="X.Org Foundation" [ 7.650] compiled for 1.19.3, module version = 2.3.4 [ 7.650] Module class: X.Org Video Driver [ 7.650] ABI class: X.Org Video Driver, version 23.0 [ 7.650] (II) NOUVEAU driver Date: Fri Apr 21 14:41:17 2017 -0400 [ 7.650] (II) NOUVEAU driver for NVIDIA chipset families : [ 7.650] RIVA TNT (NV04) [ 7.650] RIVA TNT2 (NV05) [ 7.650] GeForce 256 (NV10) [ 7.650] GeForce 2 (NV11, NV15) [ 7.650] GeForce 4MX (NV17, NV18) [ 7.650] GeForce 3 (NV20) [ 7.650] GeForce 4Ti (NV25, NV28) [ 7.650] GeForce FX (NV3x) [ 7.650] GeForce 6 (NV4x) [ 7.650] GeForce 7 (G7x) [ 7.650] GeForce 8 (G8x) [ 7.650] GeForce GTX 200 (NVA0) [ 7.650] GeForce GTX 400 (NVC0) [ 7.650] (II) modesetting: Driver for Modesetting Kernel Drivers: kms [ 7.651] (II) FBDEV: driver for framebuffer: fbdev [ 7.651] (II) VESA: driver for VESA chipsets: vesa [ 7.670] (II) [drm] nouveau interface version: 1.3.1 [ 7.670] (WW) Falling back to old probe method for modesetting [ 7.670] (WW) Falling back to old probe method for fbdev [ 7.670] (II) Loading sub module "fbdevhw" [ 7.670] (II) LoadModule: "fbdevhw" [ 7.670] (II) Loading /usr/lib/xorg/modules/libfbdevhw.so [ 7.670] (II) Module fbdevhw: vendor="X.Org Foundation" [ 7.670] compiled for 1.19.6, module version = 0.0.2 [ 7.670] ABI class: X.Org Video Driver, version 23.0 [ 7.670] (WW) Falling back to old probe method for vesa [ 7.670] (II) Loading sub module "dri2" [ 7.670] (II) LoadModule: "dri2" [ 7.670] (II) Module "dri2" already built-in [ 7.670] (--) NOUVEAU(0): Chipset: "NVIDIA NV92" [ 7.670] (II) NOUVEAU(0): Creating default Display subsection in Screen section "Default Screen Section" for depth/fbbpp 24/32 [ 7.670] (==) NOUVEAU(0): Depth 24, (--) framebuffer bpp 32 [ 7.670] (==) NOUVEAU(0): RGB weight 888 [ 7.670] (==) NOUVEAU(0): Default visual is TrueColor [ 7.670] (==) NOUVEAU(0): Using HW cursor [ 7.670] (==) NOUVEAU(0): Allowed maximum DRI level 2. [ 7.670] (==) NOUVEAU(0): GLX sync to VBlank enabled. [ 7.670] (==) NOUVEAU(0): Page flipping enabled [ 7.670] (==) NOUVEAU(0): Swap limit set to 1 [Max allowed 2] [ 7.670] (==) NOUVEAU(0): Page flipping synced to vblank by kernel. [ 7.670] (II) NOUVEAU(0): Initializing outputs ... [ 7.670] (II) NOUVEAU(0): Output LVDS-1 has no monitor section [ 7.670] (II) NOUVEAU(0): Output DVI-D-1 has no monitor section [ 7.672] (II) NOUVEAU(0): Output DVI-D-2 has no monitor section [ 7.690] (II) NOUVEAU(0): Output VGA-1 has no monitor section [ 7.690] (II) NOUVEAU(0): 4 crtcs needed for screen. [ 7.693] (II) NOUVEAU(0): Allocated crtc nr. 0 to this screen. [ 7.693] (II) NOUVEAU(0): Allocated crtc nr. 1 to this screen. [ 7.693] (II) NOUVEAU(0): EDID for output LVDS-1 [ 7.693] (II) NOUVEAU(0): EDID for output DVI-D-1 [ 7.693] (II) NOUVEAU(0): Printing probed modes for output DVI-D-1 [ 7.693] (II) NOUVEAU(0): Modeline "1920x1200"x60.0 193.15 1920 2048 2256 2592 1200 1201 1204 1242 -hsync +vsync (74.5 kHz) [ 7.693] (II) NOUVEAU(0): Modeline "1024x768"x60.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz e) [ 7.693] (II) NOUVEAU(0): Modeline "800x600"x60.3 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz e) [ 7.693] (II) NOUVEAU(0): Modeline "800x600"x56.2 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz e) [ 7.693] (II) NOUVEAU(0): Modeline "848x480"x60.0 33.75 848 864 976 1088 480 486 494 517 +hsync +vsync (31.0 kHz e) [ 7.693] (II) NOUVEAU(0): Modeline "640x480"x59.9 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz e) [ 7.699] (II) NOUVEAU(0): EDID for output DVI-D-2 [ 7.720] (II) NOUVEAU(0): EDID for output VGA-1 [ 7.720] (II) NOUVEAU(0): Output LVDS-1 disconnected [ 7.720] (II) NOUVEAU(0): Output DVI-D-1 connected [ 7.720] (II) NOUVEAU(0): Output DVI-D-2 disconnected [ 7.720] (II) NOUVEAU(0): Output VGA-1 disconnected [ 7.720] (II) NOUVEAU(0): Using exact sizes for initial modes [ 7.720] (II) NOUVEAU(0): Output DVI-D-1 using initial mode 1024x768 +0+0 [ 7.720] (==) NOUVEAU(0): Using gamma correction (1.0, 1.0, 1.0) [ 7.720] (--) NOUVEAU(0): Virtual size is 1024x768 (pitch 0) [ 7.720] (**) NOUVEAU(0): Driver mode "1024x768": 65.0 MHz (scaled from 0.0 MHz), 48.4 kHz, 60.0 Hz [ 7.720] (II) NOUVEAU(0): Modeline "1024x768"x60.0 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz e) [ 7.720] (**) NOUVEAU(0): Driver mode "800x600": 40.0 MHz (scaled from 0.0 MHz), 37.9 kHz, 60.3 Hz [ 7.720] (II) NOUVEAU(0): Modeline "800x600"x60.3 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz e) [ 7.720] (**) NOUVEAU(0): Driver mode "800x600": 36.0 MHz (scaled from 0.0 MHz), 35.2 kHz, 56.2 Hz [ 7.720] (II) NOUVEAU(0): Modeline "800x600"x56.2 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz e) [ 7.720] (**) NOUVEAU(0): Driver mode "848x480": 33.8 MHz (scaled from 0.0 MHz), 31.0 kHz, 60.0 Hz [ 7.720] (II) NOUVEAU(0): Modeline "848x480"x60.0 33.75 848 864 976 1088 480 486 494 517 +hsync +vsync (31.0 kHz e) [ 7.720] (**) NOUVEAU(0): Driver mode "640x480": 25.2 MHz (scaled from 0.0 MHz), 31.5 kHz, 59.9 Hz [ 7.720] (II) NOUVEAU(0): Modeline "640x480"x59.9 25.18 640 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz e) [ 7.720] (**) NOUVEAU(0): Mode "1920x1200": 193.2 MHz (scaled from 0.0 MHz), 74.5 kHz, 60.0 Hz [ 7.720] (II) NOUVEAU(0): Modeline "1920x1200"x60.0 193.15 1920 2048 2256 2592 1200 1201 1204 1242 -hsync +vsync (74.5 kHz) [ 7.720] (==) NOUVEAU(0): DPI set to (96, 96) [ 7.720] (II) Loading sub module "fb" [ 7.720] (II) LoadModule: "fb" [ 7.720] (II) Loading /usr/lib/xorg/modules/libfb.so [ 7.723] (II) Module fb: vendor="X.Org Foundation" [ 7.723] compiled for 1.19.6, module version = 1.0.0 [ 7.723] ABI class: X.Org ANSI C Emulation, version 0.4 [ 7.723] (II) Loading sub module "shadowfb" [ 7.723] (II) LoadModule: "shadowfb" [ 7.723] (II) Loading /usr/lib/xorg/modules/libshadowfb.so [ 7.723] (II) Module shadowfb: vendor="X.Org Foundation" [ 7.723] compiled for 1.19.6, module version = 1.0.0 [ 7.723] ABI class: X.Org ANSI C Emulation, version 0.4 ... [ 7.723] (--) Depth 24 pixmap format is 32 bpp [ 7.728] (II) NOUVEAU(0): Channel setup complete. [ 7.730] (II) NOUVEAU(0): Hardware support for Present enabled [ 7.730] (II) NOUVEAU(0): [DRI2] Setup complete [ 7.730] (II) NOUVEAU(0): [DRI2] DRI driver: nouveau [ 7.730] (II) NOUVEAU(0): [DRI2] VDPAU driver: nouveau [ 7.730] (II) Loading sub module "exa" [ 7.730] (II) LoadModule: "exa" [ 7.730] (II) Loading /usr/lib/xorg/modules/libexa.so [ 7.730] (II) Module exa: vendor="X.Org Foundation" [ 7.730] compiled for 1.19.6, module version = 2.6.0 [ 7.730] ABI class: X.Org Video Driver, version 23.0 [ 7.730] (II) EXA(0): Driver allocated offscreen pixmaps [ 7.730] (II) EXA(0): Driver registered support for the following operations: [ 7.730] (II) Solid [ 7.730] (II) Copy [ 7.730] (II) Composite (RENDER acceleration) [ 7.730] (II) UploadToScreen [ 7.730] (II) DownloadFromScreen [ 7.730] (==) NOUVEAU(0): Backing store enabled [ 7.730] (==) NOUVEAU(0): Silken mouse enabled [ 7.730] (II) NOUVEAU(0): [XvMC] Associated with Nouveau GeForce 8/9 Textured Video. [ 7.730] (II) NOUVEAU(0): [XvMC] Extension initialized. [ 7.730] (==) NOUVEAU(0): DPMS enabled [ 7.730] (II) NOUVEAU(0): RandR 1.2 enabled, ignore the following RandR disabled message. ... [ 7.831] (II) AIGLX: Loaded and initialized nouveau [ 7.831] (II) GLX: Initialized DRI2 GL provider for screen 0 [ 7.834] (II) NOUVEAU(0): NVEnterVT is called. [ 7.880] (II) NOUVEAU(0): Setting screen physical size to 270 x 203 [ 7.880] resize called 1024 768 Could you tell me, how to get the monitor running with 1920x1200, not 960x1200(what ist the half x of 1920)? Nb.:propietary nvidi-adriver v340 works with LVDS and DVI-D-1, (but chrashes after a while) Thank you a lot, Wolfgang
Wolfgang Rißler
2018-Sep-23 16:26 UTC
[Nouveau] Strange monitor behavior on forced DVI-D output
Am Freitag, den 07.09.2018, 22:11 +0200 schrieb wolle321 at freenet.de:> Hello , > > I'm new here but I hope I can describe my problem exactly. > > I'm trying to get my DVI-Monitor to work with nouveau. The monitor > is > automatically reported as not connected. LVDS is detected. Forcing it > on Xorg.conf didn't work, KMS does: > > video=DVI-D-1:1920x1200e video=LVDS-1:d > > X started with 1024x768, but could switch by xrandr to 1920x1200. > > The viewed picture now is 1920x1200 , but the Monitor runs on > 960x1200, > so that it looks very pixelated. (But there is no panning) > > Tried to add another (cvt calculated) modeline (1920x1200_60.00) with > xrandr, but didnt help: > > > Screen 0: minimum 320 x 200, current 1920 x 1200, maximum 8192 x 8192 > LVDS-1 disconnected (normal left inverted right x axis y axis) > DVI-D-1 connected 1920x1200+0+0 (normal left inverted right x axis y > axis) 0mm x 0mm > 1920x1200 60.00 > 1024x768 60.00 > 800x600 60.32 56.25 > 848x480 60.00 > 640x480 59.94 > 1920x1200_60.00 59.88* > > dmesg: > ... > [ 1.526099] fb: switching to nouveaufb from VESA VGA > [ 1.526125] Console: switching to colour dummy device 80x25 > [ 1.526265] scsi host0: ahci > [ 1.526284] nouveau 0000:01:00.0: NVIDIA G92 (092f00a2) > [ 1.531073] scsi host1: ahci > [ 1.535016] scsi host2: ahci > [ 1.541021] scsi host3: ahci > [ 1.548031] scsi host4: ahci > [ 1.553014] scsi host5: ahci > [ 1.553064] ata1: SATA max UDMA/133 abar m2048 at 0xdb325000 port > 0xdb325100 irq 29 > [ 1.553067] ata2: SATA max UDMA/133 abar m2048 at 0xdb325000 port > 0xdb325180 irq 29 > [ 1.553068] ata3: DUMMY > [ 1.553070] ata4: DUMMY > [ 1.553073] ata5: SATA max UDMA/133 abar m2048 at 0xdb325000 port > 0xdb325300 irq 29 > [ 1.553076] ata6: SATA max UDMA/133 abar m2048 at 0xdb325000 port > 0xdb325380 irq 29 > [ 1.553513] e1000e 0000:00:19.0: Interrupt Throttling Rate > (ints/sec) set to dynamic conservative mode > [ 1.590043] firewire_ohci 0000:86:06.0: added OHCI v1.10 device as > card 0, 4 IR + 4 IT contexts, quirks 0x11 > [ 1.678230] nouveau 0000:01:00.0: bios: version 62.92.6e.00.10 > [ 1.678547] nouveau 0000:01:00.0: mxm: BIOS version 2.0 > [ 1.680769] nouveau 0000:01:00.0: mxm: unmatched output device > 0103010201010100 > [ 1.701487] nouveau 0000:01:00.0: fb: 1024 MiB GDDR3 > [ 1.711344] e1000e 0000:00:19.0 eth0: (PCI Express:2.5GT/s:Width > x1) 00:24:81:62:88:f7 > [ 1.711351] e1000e 0000:00:19.0 eth0: Intel(R) PRO/1000 Network > Connection > [ 1.711374] e1000e 0000:00:19.0 eth0: MAC: 7, PHY: 8, PBA No: > 1052FF-0FF > [ 1.712279] e1000e 0000:00:19.0 enp0s25: renamed from eth0 > [ 1.775146] [TTM] Zone kernel: Available graphics memory: 4066038 > kiB > [ 1.775148] [TTM] Zone dma32: Available graphics memory: 2097152 > kiB > [ 1.775150] [TTM] Initializing pool allocator > [ 1.775159] [TTM] Initializing DMA pool allocator > [ 1.775171] nouveau 0000:01:00.0: DRM: VRAM: 1024 MiB > [ 1.775173] nouveau 0000:01:00.0: DRM: GART: 1048576 MiB > [ 1.775177] nouveau 0000:01:00.0: DRM: TMDS table version 2.0 > [ 1.775179] nouveau 0000:01:00.0: DRM: DCB version 4.0 > [ 1.775182] nouveau 0000:01:00.0: DRM: DCB outp 00: 01000323 > 00010034 > [ 1.775185] nouveau 0000:01:00.0: DRM: DCB outp 01: 02011312 > 00020030 > [ 1.775187] nouveau 0000:01:00.0: DRM: DCB outp 02: 02022312 > 00020020 > [ 1.775190] nouveau 0000:01:00.0: DRM: DCB outp 05: 02034300 > 00000028 > [ 1.775192] nouveau 0000:01:00.0: DRM: DCB conn 00: 00000040 > [ 1.775194] nouveau 0000:01:00.0: DRM: DCB conn 01: 00001131 > [ 1.775196] nouveau 0000:01:00.0: DRM: DCB conn 02: 00002231 > [ 1.775198] nouveau 0000:01:00.0: DRM: DCB conn 03: 00110346 > [ 1.775200] nouveau 0000:01:00.0: DRM: DCB conn 04: 00000400 > [ 1.775202] nouveau 0000:01:00.0: DRM: DCB conn 05: 00000510 > [ 1.775203] nouveau 0000:01:00.0: DRM: DCB conn 06: 00000511 > [ 1.775205] nouveau 0000:01:00.0: DRM: DCB conn 07: 00000513 > [ 1.775207] nouveau 0000:01:00.0: DRM: DCB conn 08: 00002631 > [ 1.775209] nouveau 0000:01:00.0: DRM: DCB conn 09: 00001731 > [ 1.775211] nouveau 0000:01:00.0: DRM: DCB conn 10: 00002831 > [ 1.775213] nouveau 0000:01:00.0: DRM: DCB conn 11: 00110946 > [ 1.775215] nouveau 0000:01:00.0: DRM: DCB conn 12: 00000a00 > [ 1.775217] nouveau 0000:01:00.0: DRM: DCB conn 13: 00000b10 > [ 1.775219] nouveau 0000:01:00.0: DRM: DCB conn 14: 00000b11 > [ 1.775221] nouveau 0000:01:00.0: DRM: DCB conn 15: 00000b13 > [ 1.776874] [drm] forcing LVDS-1 connector off > [ 1.776924] [drm] forcing DVI-D-1 connector on > [ 1.777030] [drm] Supports vblank timestamp caching Rev 2 > (21.10.2013). > [ 1.777031] [drm] Driver supports precise vblank timestamp query. > [ 1.779020] nouveau 0000:01:00.0: DRM: MM: using CRYPT for buffer > copies > [ 1.791526] nouveau 0000:01:00.0: DRM: allocated 1920x1200 fb: > 0x70000, bo (ptrval) > [ 1.792143] fbcon: nouveaufb (fb0) is primary device > [ 1.792399] Console: switching to colour frame buffer device > 240x75 > [ 1.792449] nouveau 0000:01:00.0: fb0: nouveaufb frame buffer > device > [ 1.794020] usb 3-1: new full-speed USB device number 2 using > uhci_hcd > [ 1.797047] [drm] Initialized nouveau 1.3.1 20120801 for > 0000:01:00.0 on minor 0 > ... > [ 37.435414] nouveau 0000:01:00.0: Direct firmware load for > nouveau/nv84_xuc00f failed with error -2 > [ 37.435418] nouveau 0000:01:00.0: vp: unable to load firmware > nouveau/nv84_xuc00f > [ 37.435420] nouveau 0000:01:00.0: vp: init failed, -2 > > Xorg.0.log: > ... > > [ 7.646] (==) Matched nouveau as autoconfigured driver 0 > [ 7.646] (==) Matched nouveau as autoconfigured driver 1 > [ 7.646] (==) Matched modesetting as autoconfigured driver 2 > [ 7.646] (==) Matched fbdev as autoconfigured driver 3 > [ 7.646] (==) Matched vesa as autoconfigured driver 4 > [ 7.646] (==) Assigned the driver to the xf86ConfigLayout > [ 7.646] (II) LoadModule: "nouveau" > [ 7.648] (II) Loading > /usr/lib/xorg/modules/drivers/nouveau_drv.so > [ 7.649] (II) Module nouveau: vendor="X.Org Foundation" > [ 7.649] compiled for 1.19.3, module version = 1.0.15 > [ 7.649] Module class: X.Org Video Driver > [ 7.649] ABI class: X.Org Video Driver, version 23.0 > [ 7.649] (II) LoadModule: "modesetting" > [ 7.650] (II) Loading > /usr/lib/xorg/modules/drivers/modesetting_drv.so > [ 7.650] (II) Module modesetting: vendor="X.Org Foundation" > [ 7.650] compiled for 1.19.6, module version = 1.19.6 > [ 7.650] Module class: X.Org Video Driver > [ 7.650] ABI class: X.Org Video Driver, version 23.0 > [ 7.650] (II) LoadModule: "fbdev" > [ 7.650] (II) Loading /usr/lib/xorg/modules/drivers/fbdev_drv.so > [ 7.650] (II) Module fbdev: vendor="X.Org Foundation" > [ 7.650] compiled for 1.19.3, module version = 0.4.4 > [ 7.650] Module class: X.Org Video Driver > [ 7.650] ABI class: X.Org Video Driver, version 23.0 > [ 7.650] (II) LoadModule: "vesa" > [ 7.650] (II) Loading /usr/lib/xorg/modules/drivers/vesa_drv.so > [ 7.650] (II) Module vesa: vendor="X.Org Foundation" > [ 7.650] compiled for 1.19.3, module version = 2.3.4 > [ 7.650] Module class: X.Org Video Driver > [ 7.650] ABI class: X.Org Video Driver, version 23.0 > [ 7.650] (II) NOUVEAU driver Date: Fri Apr 21 14:41:17 2017 > -0400 > [ 7.650] (II) NOUVEAU driver for NVIDIA chipset families : > [ 7.650] RIVA TNT (NV04) > [ 7.650] RIVA TNT2 (NV05) > [ 7.650] GeForce 256 (NV10) > [ 7.650] GeForce 2 (NV11, NV15) > [ 7.650] GeForce 4MX (NV17, NV18) > [ 7.650] GeForce 3 (NV20) > [ 7.650] GeForce 4Ti (NV25, NV28) > [ 7.650] GeForce FX (NV3x) > [ 7.650] GeForce 6 (NV4x) > [ 7.650] GeForce 7 (G7x) > [ 7.650] GeForce 8 (G8x) > [ 7.650] GeForce GTX 200 (NVA0) > [ 7.650] GeForce GTX 400 (NVC0) > [ 7.650] (II) modesetting: Driver for Modesetting Kernel Drivers: > kms > [ 7.651] (II) FBDEV: driver for framebuffer: fbdev > [ 7.651] (II) VESA: driver for VESA chipsets: vesa > [ 7.670] (II) [drm] nouveau interface version: 1.3.1 > [ 7.670] (WW) Falling back to old probe method for modesetting > [ 7.670] (WW) Falling back to old probe method for fbdev > [ 7.670] (II) Loading sub module "fbdevhw" > [ 7.670] (II) LoadModule: "fbdevhw" > [ 7.670] (II) Loading /usr/lib/xorg/modules/libfbdevhw.so > [ 7.670] (II) Module fbdevhw: vendor="X.Org Foundation" > [ 7.670] compiled for 1.19.6, module version = 0.0.2 > [ 7.670] ABI class: X.Org Video Driver, version 23.0 > [ 7.670] (WW) Falling back to old probe method for vesa > [ 7.670] (II) Loading sub module "dri2" > [ 7.670] (II) LoadModule: "dri2" > [ 7.670] (II) Module "dri2" already built-in > [ 7.670] (--) NOUVEAU(0): Chipset: "NVIDIA NV92" > [ 7.670] (II) NOUVEAU(0): Creating default Display subsection in > Screen section > "Default Screen Section" for depth/fbbpp 24/32 > [ 7.670] (==) NOUVEAU(0): Depth 24, (--) framebuffer bpp 32 > [ 7.670] (==) NOUVEAU(0): RGB weight 888 > [ 7.670] (==) NOUVEAU(0): Default visual is TrueColor > [ 7.670] (==) NOUVEAU(0): Using HW cursor > [ 7.670] (==) NOUVEAU(0): Allowed maximum DRI level 2. > [ 7.670] (==) NOUVEAU(0): GLX sync to VBlank enabled. > [ 7.670] (==) NOUVEAU(0): Page flipping enabled > [ 7.670] (==) NOUVEAU(0): Swap limit set to 1 [Max allowed 2] > [ 7.670] (==) NOUVEAU(0): Page flipping synced to vblank by > kernel. > [ 7.670] (II) NOUVEAU(0): Initializing outputs ... > [ 7.670] (II) NOUVEAU(0): Output LVDS-1 has no monitor section > [ 7.670] (II) NOUVEAU(0): Output DVI-D-1 has no monitor section > [ 7.672] (II) NOUVEAU(0): Output DVI-D-2 has no monitor section > [ 7.690] (II) NOUVEAU(0): Output VGA-1 has no monitor section > [ 7.690] (II) NOUVEAU(0): 4 crtcs needed for screen. > [ 7.693] (II) NOUVEAU(0): Allocated crtc nr. 0 to this screen. > [ 7.693] (II) NOUVEAU(0): Allocated crtc nr. 1 to this screen. > [ 7.693] (II) NOUVEAU(0): EDID for output LVDS-1 > [ 7.693] (II) NOUVEAU(0): EDID for output DVI-D-1 > [ 7.693] (II) NOUVEAU(0): Printing probed modes for output DVI-D- > 1 > [ 7.693] (II) NOUVEAU(0): Modeline "1920x1200"x60.0 193.15 1920 > 2048 2256 2592 1200 1201 1204 1242 -hsync +vsync (74.5 kHz) > [ 7.693] (II) NOUVEAU(0): Modeline "1024x768"x60.0 65.00 1024 > 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz e) > [ 7.693] (II) NOUVEAU(0): Modeline "800x600"x60.3 40.00 800 > 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz e) > [ 7.693] (II) NOUVEAU(0): Modeline "800x600"x56.2 36.00 800 > 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz e) > [ 7.693] (II) NOUVEAU(0): Modeline "848x480"x60.0 33.75 848 > 864 976 1088 480 486 494 517 +hsync +vsync (31.0 kHz e) > [ 7.693] (II) NOUVEAU(0): Modeline "640x480"x59.9 25.18 640 > 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz e) > [ 7.699] (II) NOUVEAU(0): EDID for output DVI-D-2 > [ 7.720] (II) NOUVEAU(0): EDID for output VGA-1 > [ 7.720] (II) NOUVEAU(0): Output LVDS-1 disconnected > [ 7.720] (II) NOUVEAU(0): Output DVI-D-1 connected > [ 7.720] (II) NOUVEAU(0): Output DVI-D-2 disconnected > [ 7.720] (II) NOUVEAU(0): Output VGA-1 disconnected > [ 7.720] (II) NOUVEAU(0): Using exact sizes for initial modes > [ 7.720] (II) NOUVEAU(0): Output DVI-D-1 using initial mode > 1024x768 +0+0 > [ 7.720] (==) NOUVEAU(0): Using gamma correction (1.0, 1.0, 1.0) > [ 7.720] (--) NOUVEAU(0): Virtual size is 1024x768 (pitch 0) > [ 7.720] (**) NOUVEAU(0): Driver mode "1024x768": 65.0 MHz > (scaled from 0.0 MHz), 48.4 kHz, 60.0 Hz > [ 7.720] (II) NOUVEAU(0): Modeline "1024x768"x60.0 65.00 1024 > 1048 1184 1344 768 771 777 806 -hsync -vsync (48.4 kHz e) > [ 7.720] (**) NOUVEAU(0): Driver mode "800x600": 40.0 MHz > (scaled from 0.0 MHz), 37.9 kHz, 60.3 Hz > [ 7.720] (II) NOUVEAU(0): Modeline "800x600"x60.3 40.00 800 > 840 968 1056 600 601 605 628 +hsync +vsync (37.9 kHz e) > [ 7.720] (**) NOUVEAU(0): Driver mode "800x600": 36.0 MHz > (scaled from 0.0 MHz), 35.2 kHz, 56.2 Hz > [ 7.720] (II) NOUVEAU(0): Modeline "800x600"x56.2 36.00 800 > 824 896 1024 600 601 603 625 +hsync +vsync (35.2 kHz e) > [ 7.720] (**) NOUVEAU(0): Driver mode "848x480": 33.8 MHz > (scaled from 0.0 MHz), 31.0 kHz, 60.0 Hz > [ 7.720] (II) NOUVEAU(0): Modeline "848x480"x60.0 33.75 848 > 864 976 1088 480 486 494 517 +hsync +vsync (31.0 kHz e) > [ 7.720] (**) NOUVEAU(0): Driver mode "640x480": 25.2 MHz > (scaled from 0.0 MHz), 31.5 kHz, 59.9 Hz > [ 7.720] (II) NOUVEAU(0): Modeline "640x480"x59.9 25.18 640 > 656 752 800 480 490 492 525 -hsync -vsync (31.5 kHz e) > [ 7.720] (**) NOUVEAU(0): Mode "1920x1200": 193.2 MHz (scaled > from 0.0 MHz), 74.5 kHz, 60.0 Hz > [ 7.720] (II) NOUVEAU(0): Modeline "1920x1200"x60.0 193.15 1920 > 2048 2256 2592 1200 1201 1204 1242 -hsync +vsync (74.5 kHz) > [ 7.720] (==) NOUVEAU(0): DPI set to (96, 96) > [ 7.720] (II) Loading sub module "fb" > [ 7.720] (II) LoadModule: "fb" > [ 7.720] (II) Loading /usr/lib/xorg/modules/libfb.so > [ 7.723] (II) Module fb: vendor="X.Org Foundation" > [ 7.723] compiled for 1.19.6, module version = 1.0.0 > [ 7.723] ABI class: X.Org ANSI C Emulation, version 0.4 > [ 7.723] (II) Loading sub module "shadowfb" > [ 7.723] (II) LoadModule: "shadowfb" > [ 7.723] (II) Loading /usr/lib/xorg/modules/libshadowfb.so > [ 7.723] (II) Module shadowfb: vendor="X.Org Foundation" > [ 7.723] compiled for 1.19.6, module version = 1.0.0 > [ 7.723] ABI class: X.Org ANSI C Emulation, version 0.4 > ... > [ 7.723] (--) Depth 24 pixmap format is 32 bpp > [ 7.728] (II) NOUVEAU(0): Channel setup complete. > [ 7.730] (II) NOUVEAU(0): Hardware support for Present enabled > [ 7.730] (II) NOUVEAU(0): [DRI2] Setup complete > [ 7.730] (II) NOUVEAU(0): [DRI2] DRI driver: nouveau > [ 7.730] (II) NOUVEAU(0): [DRI2] VDPAU driver: nouveau > [ 7.730] (II) Loading sub module "exa" > [ 7.730] (II) LoadModule: "exa" > [ 7.730] (II) Loading /usr/lib/xorg/modules/libexa.so > [ 7.730] (II) Module exa: vendor="X.Org Foundation" > [ 7.730] compiled for 1.19.6, module version = 2.6.0 > [ 7.730] ABI class: X.Org Video Driver, version 23.0 > [ 7.730] (II) EXA(0): Driver allocated offscreen pixmaps > [ 7.730] (II) EXA(0): Driver registered support for the following > operations: > [ 7.730] (II) Solid > [ 7.730] (II) Copy > [ 7.730] (II) Composite (RENDER acceleration) > [ 7.730] (II) UploadToScreen > [ 7.730] (II) DownloadFromScreen > [ 7.730] (==) NOUVEAU(0): Backing store enabled > [ 7.730] (==) NOUVEAU(0): Silken mouse enabled > [ 7.730] (II) NOUVEAU(0): [XvMC] Associated with Nouveau GeForce > 8/9 Textured Video. > [ 7.730] (II) NOUVEAU(0): [XvMC] Extension initialized. > [ 7.730] (==) NOUVEAU(0): DPMS enabled > [ 7.730] (II) NOUVEAU(0): RandR 1.2 enabled, ignore the following > RandR disabled message. > ... > [ 7.831] (II) AIGLX: Loaded and initialized nouveau > [ 7.831] (II) GLX: Initialized DRI2 GL provider for screen 0 > [ 7.834] (II) NOUVEAU(0): NVEnterVT is called. > [ 7.880] (II) NOUVEAU(0): Setting screen physical size to 270 x > 203 > [ 7.880] resize called 1024 768 > > Could you tell me, how to get the monitor running with 1920x1200, not > 960x1200(what ist the half x of 1920)? > > Nb.:propietary nvidi-adriver v340 works with LVDS and DVI-D-1, (but > chrashes after a while) > > Thank you a lot, Wolfgang > _______________________________________________ > Nouveau mailing list > Nouveau at lists.freedesktop.org > https://lists.freedesktop.org/mailman/listinfo/nouveauHello again, I try to send a friendly ping to my problem. At the moment I'm running at 1600x1200 (monitor than has 1600x1200 too), what looks better then 1920x1200 picture on that Monitor with 960x1200. I cant get 1920x1200 working, but I'm shure, that the monitor has this native resolution. (proprietary nvidia-driver does it, but freezes after 20min, of course, not your problem). 1920x1200 on the internal LVDS - Monitor of the Laptop with nouveau works. When I boot up with kms video=DVI-D-1:e video=LVDS-1:d, the screen shows 1024x786. Could you give me any hint, what am I doing wrong, or what I could try to get DVI-Monitor working? Could the be a bug in the EDID-data from the monitor? When I boot up with kms video=DVI-D-1:e video=LVDS-1:d, the screen shows 1024x786, no higher modes are available (but I can add them via xrandr) Help would be very appreciated, I searched the web for hours, no sensfull hint. Thank you, Wolfgang
Ilia Mirkin
2018-Sep-23 16:55 UTC
[Nouveau] Strange monitor behavior on forced DVI-D output
On Sun, Sep 23, 2018 at 12:26 PM, Wolfgang Rißler <wolle321 at freenet.de> wrote:> I try to send a friendly ping to my problem. > At the moment I'm running at 1600x1200 (monitor than has 1600x1200 > too), what looks better then 1920x1200 picture on that Monitor with > 960x1200. > I cant get 1920x1200 working, but I'm shure, that the monitor has this > native resolution. (proprietary nvidia-driver does it, but freezes > after 20min, of course, not your problem). > > 1920x1200 on the internal LVDS - Monitor of the Laptop with nouveau > works. > > When I boot up with kms video=DVI-D-1:e video=LVDS-1:d, the screen > shows 1024x786.That's not extremely surprising ... force-enabling an output I think might kill the resolution detection, and 1024x768 is the default. Why are you force-enabling/disabling video outputs? That should not generally be necessary.> > Could you give me any hint, what am I doing wrong, or what I could try > to get DVI-Monitor working? > > Could the be a bug in the EDID-data from the monitor?Could be. I'd encourage you to file a bug with the relevant data (e.g. a copy of your monitor's edid, which can be obtained from /sys/class/drm/card0-$conn/edid or so, probably dmesg, anything else you think is relevant). Cheers, -ilia