asterisk users - Apr 2007 - Asterisk installation issue - CLI showing 0 active channels

Hi All,
   I would appreciate a lot if you could help me. I have installed Asterisk
1.4.1 and zaptel 1.4.2 on my redhat enterprise linux 4. I have also
installed 1 FXO port card: Digium TDM400P.
After loading zaptel driver I could see my digium card's led glow green.
Tested with zttool that its in OK state. I have configured fxsks=4 in
zaptel.conf(channel 4 cause FXO module is on port 4). I have also configured
channel 4 in incoming context in zapata.conf.

After all configuration I started asterisk with vvvvvgc and made a call, but
I didn't see any call log on asterisk console.
When I did core show channels its showing 0 active channels. Looks like I
did something wrong in my config.

Also I dont see red-alarm in zttool if I take out pstn line.

I have taken pstn line from my Vonage adapter and connecting that to my
digium card.

Any help will be appreciated.
Regards,
Vijay Gaur
-------------- next part --------------
An HTML attachment was scrubbed...
URL:
http://lists.digium.com/pipermail/asterisk-users/attachments/20070409/57482739/attachment.htm

Vijay Gaur wrote:
> 
> 
> Hi All,
>    I would appreciate a lot if you could help me. I have installed
> Asterisk 1.4.1 and zaptel 1.4.2 on my redhat enterprise linux 4. I have
> also installed 1 FXO port card: Digium TDM400P.
> After loading zaptel driver I could see my digium card's led glow
green.
> Tested with zttool that its in OK state. I have configured fxsks=4 in
> zaptel.conf(channel 4 cause FXO module is on port 4). I have also
> configured channel 4 in incoming context in zapata.conf.
>  
> After all configuration I started asterisk with vvvvvgc and made a call,
> but I didn't see any call log on asterisk console.
We need much more information.
>From *where* did you make a call? Did you dial from another location
into the Asterisk number (e.g., did you dial your Vonage number from
outside?), or did you call out from your Asterisk server using an
internal extension?

Does the call succeed? Do you hear ringing, or a fast busy, or does the
call go to voice mail?

What is in your dialplan (extensions.conf)?
> When I did core show channels its showing 0 active channels. Looks like
> I did something wrong in my config.
>  
> Also I dont see red-alarm in zttool if I take out pstn line.
I don't think the TDM400P cards do media detection :) You're probably
looking for the problem in the wrong place -- but answer the above
questions first and we'll see what we can figure out.

-Stephen-

I hear ring few times and then it goes to voice mail. Looks like call is not
going to asterisk. My regular phone attached to that line works fine.
Regards,
Vijay


On 4/9/07, Stephen Bosch <posting@vodacomm.ca>
wrote:
>
> Vijay Gaur wrote:
> > Hi Stephen,
> >   I made the call from outside phone(cellphone) to my vonage number.
> > Call went to the voicemail. My extension.conf has
> > [incoming]
> > exten=>s,1,Answer() and more lines.
> >
> > I assume core show channels should show 1 active channel. Its showing
0.
>
> Your calls are not even going into Asterisk.
>
> When it goes to voice mail, do you hear it ring a few times first, or
> does it go directly to voicemail?
>
> Does a regular telephone plugged into the Vonage adapter work?
>
> -Stephen-
> _______________________________________________
> --Bandwidth and Colocation provided by Easynews.com --
>
> asterisk-users mailing list
> To UNSUBSCRIBE or update options visit:
>   http://lists.digium.com/mailman/listinfo/asterisk-users
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL:
http://lists.digium.com/pipermail/asterisk-users/attachments/20070409/64c8f28f/attachment.htm