similar to: Asterisk installation issue - CLI showing 0 active channels

We are trying to configure shorewall as follows: 1. We have shorewall running at gateway (172.16.1.1) with NAT. 2. We have a number of web servers (172.16.1.x/24). These web servers are accessed through port forwarding at the gateway (172.16.1.1) and websites are visible through virtual hosting through a web re-director. 3. Presently the proxy server runs in a transparent mode, i.e., all web

Hello, Is there any possibility of integrating plans of vonage with asterisk. Regards Vijay Gandhi

I am trying to install the Modified Prepaid App. I have installed PostgeSQL, created the tables, etc. Make Install runs ok. The when I try to launch asterisk (asterisk -vvvvvgc), it fails to run. I get the following errors, 1st error: [app_prepaid.so] => (Prepaid Application) == Parsing '/etc/asterisk/prepaid.conf': Found Jun 16 14:27:27 ERROR[-1085267840]: app_prepaid.c:127

Hi, my zaphfc is flooding my syslog with two messages (even without asterisk running). Is this "normal"?: -------------------------------------------------- zaphfc: bchan rx fifo not enough bytes to receive! (z1=1360, z2=1353, wanted 8 got 7), probably a buffer overrun. zaphfc: dropped audio (z1=2712, z2=2695, wanted 8 got 17, dropped 9). With Asterisk running (asterisk -vvvvvgc)

Hi, Apologies in advance for the lengthy email. I'm new to asterisk and have trouble with isdn4linux. The setup is very basic like this: winxp ------- asterisk -------- winxp x-lite | x-lite | pstn The hardware involved is: Compaq EVO with RH9/kernel 2.4.20-30.9. Fritz!Card PCI v2 Asterisk CVS-04/17/04-21:36:18 Basically

Hello I'm trying to set up Asterisk on an older AMD Duron 700MHz with Fedora 5 for use with SIP phones and the Linksys 3102 SIP gateway (ie. no FXO card, so no need for zaptel and libpri), but I'm stuck: The GrandStream BudgeTone phone fails registering with Asterisk :-/ Following the "Asterisk - The Future of Telephony.pdf", here's what I did: 1. Installed Fedora 5,

I know Vonage doesn't officially have a "bring your own device" type program, but they do offer a softphone. Has anyone gotten Asterisk to connect directly to Vonage? This would be a great help!! -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20060329/5bc9f644/attachment.htm

Hi, I'm trying to get Asterisk to connect to Vonage (softphone acct) to allow me to place and receive calls. I have successfully configured Asterisk to route inbound calls and send them to the correct extension, but I can't get outbound calls to work. I have Asterisk successfully registering with Vonage, but when an INVITE is sent out, I get a "404 Not Found" back from Vonage

I setup a vonage account last year, and cancelled it last night when I put my asterisk box together and signed up for a Broadvoice account to use with it. Now I would like to use my Linksys router as an MTA, but realize it is still programmed with all of vonage's proprietary information and I do not know how to clear it. I understand that just pushing the reset button will not do it.

Hi Nitesh, check out my config that I have for the Faktortel config in the asterisk@home sourceforge forum, you'll probably be able to work out how to set it up from there. Cheers, Dean -----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of Nitesh Divecha Sent: Wednesday, February 23, 2005 4:12 PM To:

Will Vonage unlock your ATA for you for the $15? Or someone else? I have an ATA from them I would like to use with asterisk as well. -----Original Message----- From: asterisk-users-admin@lists.digium.com [mailto:asterisk-users-admin@lists.digium.com] On Behalf Of Jay Milk Sent: Thursday, April 29, 2004 8:16 PM To: asterisk-users@lists.digium.com Subject: [Asterisk-Users] Vonage and * (and what

I'm trying to connect my Asterisk server via sip using my vonage soft phone account. Has any anyone successfully got to work? I get error from asterisk saying: == Parsing '/etc/asterisk/sip.conf': == Parsing '/etc/asterisk/sip.conf': Found Aug 24 11:01:11 WARNING[1125329600]: acl.c:146 ast_get_ip: Unable to lookup '216.115.25.199:5061' when trying to register with

Hi All I am trying to dial out using SIP and Vonage using the instructions : <a href="http&#58;&#47;&#47;www.voip-info.org&#47;wiki&#47;view&#47;Asterisk&#43;and&#43;Vonage" target="_blank"

I just installed Asterisk on my server and I have Vonage softphone. I need my Asterisk server to receive calls through the Vonage Softphone DID and make outgoing calls through the Vonage ATA using an X100p to connect to it. Can someone help me out on configuring this? I really need this for my business and would greatly appreciate the help.

On Thu, Aug 6, 2015 at 11:56 AM, Murthy Gandikota <murthy64 at hotmail.com> wrote: > Tested with X-Lite and it worked fiine. Is there some way to replace > "Anonymous" with a config parameter? > > Thanks for your kind help > > ---------------------------------------- > > From: murthy64 at hotmail.com > > To: asterisk-users at lists.digium.com >

I have an IVR application that works fine from multiple DID sources, unless the call to that DID was from a Vonage service user. In this case about half the DTMF tones never get recognized by Asterisk. Has anyone else seen this? Suggestions? I'm running 1.0.9.

My boss is insisting we support fax, and I keep telling him that Fax over IP is very unreliable and not recommended and his immediate come-back is "Vonage does it." and it's very hard to figure out how. I don't think Vonage does T.38, the Linksys/Sipura units they're using doesn't support T.38 to my knowledge. That means they have to be using G.711Ulaw to send faxes.

Okay, my last post for the night. So, after tweaking my iptables rules I placed a test call from my * -> Vonage softphone account, to my Vonage main account (which uses the Motorola device). Once connected I tried punching a few DTMF's to check the quality and found I had been transferred to a fax machine. ???? Did I find a secret entrance to some fax machine at Vonage, or

I am new to the mailing list, but I am very interested in running my small home business office phone system using Asterisk. However, Broadvoice, a VoIP provider of choice based on my research, is not available in my area. I currently use Vonage VoIP. Their website mentions nothing about being able to link to Asterisk. I was wondering if any US subscribers have been able to configure Vonage

Listonians, Anyone get * to work together with Vonage? Thanks, Jerry