thr3ads.net - asterisk users - [Asterisk-Users] HELP!!!! Weird TDM2406E unable to bridge all outgoing calls. [Jun 2006]

If this information is useful, please help other people find it:
Share via:

Anderson Ling

2006-Jun-06 23:46 UTC

[Asterisk-Users] HELP!!!! Weird TDM2406E unable to bridge all outgoing calls.

Hi all,
I have TDM2406E with 24FXO ports connecting to 10 POTS line sitting in 
my office. the out going calls symptom like when called party pickup the 
phone but the calling party still hearing the ring tone from the IP phone.
Please light me up. it been many sleepless night by googling around 
trying to get the right answers.

The digium card running on Intel 915G chipset. Below are my zaptel 
configurations.
asterisk version: 1.2.9.1
Zaptel Version: 1.2.6 Echo Canceller: KB1
# Span 1: WCTDM/0 "Wildcard TDM2400P Prototype Board 1"
fxsks=1
fxsks=2
fxsks=3
fxsks=4
fxsks=5
    |
    |
fxsks=21
fxsks=22
fxsks=23
fxsks=24

# Global data
loadzone        = us
defaultzone     = us

[root#] lspci -vb

06:00.0 Ethernet controller: Digium, Inc. Wildcard TDM2400P (rev 11)
        Subsystem: Digium, Inc. Wildcard TDM2400P
        Flags: bus master, medium devsel, latency 32, IRQ 3
        I/O ports at b800
        Memory at ff520000 (32-bit, non-prefetchable)
        Expansion ROM at ff500000 [disabled]
        Capabilities: [c0] Power Management version 2

[root#] dmesg

--------snip -----------
Zapata Telephony Interface Registered on major 196
Zaptel Version: 1.2.6 Echo Canceller: KB1
PCI: Found IRQ 3 for device 0000:06:00.0
PCI Config reg is 02900117
WCTDM2400P: New Reg: fe590000!
Detected REG0: 00000100
Detected REG1: 00007849
Detected REG2: 0000001d
(pre) Reg fc is 50000027
(post) Reg fc is 50000024
Detected REG2: 0000ffff
wctdm2400p: reg is a04c0004
Resetting the modules...
During Resetting the modules...
After resetting the modules...
Port 1: Installed -- AUTO FXO (MALAYSIA mode)
Port 2: Installed -- AUTO FXO (MALAYSIA mode)
Port 3: Installed -- AUTO FXO (MALAYSIA mode)
Port 4: Installed -- AUTO FXO (MALAYSIA mode)
Port 5: Installed -- AUTO FXO (MALAYSIA mode)
Port 6: Installed -- AUTO FXO (MALAYSIA mode)
Port 7: Installed -- AUTO FXO (MALAYSIA mode)
Port 8: Installed -- AUTO FXO (MALAYSIA mode)
Port 9: Installed -- AUTO FXO (MALAYSIA mode)
Port 10: Installed -- AUTO FXO (MALAYSIA mode)
Port 11: Installed -- AUTO FXO (MALAYSIA mode)
Port 12: Installed -- AUTO FXO (MALAYSIA mode)
Port 13: Installed -- AUTO FXO (MALAYSIA mode)
Port 14: Installed -- AUTO FXO (MALAYSIA mode)
Port 15: Installed -- AUTO FXO (MALAYSIA mode)
Port 16: Installed -- AUTO FXO (MALAYSIA mode)
Port 17: Installed -- AUTO FXO (MALAYSIA mode)
Port 18: Installed -- AUTO FXO (MALAYSIA mode)
Port 19: Installed -- AUTO FXO (MALAYSIA mode)
Port 20: Installed -- AUTO FXO (MALAYSIA mode)
Port 21: Installed -- AUTO FXO (MALAYSIA mode)
Port 22: Installed -- AUTO FXO (MALAYSIA mode)
Port 23: Installed -- AUTO FXO (MALAYSIA mode)
Port 24: Installed -- AUTO FXO (MALAYSIA mode)
VPM Revision: 01
VPM: U-law mode
VPM: DTMF threshold set to 1250
VPM: Present and operational (Rev B)
Found a Wildcard TDM: Wildcard TDM2400P Prototype (24 modules)
Registered tone zone 0 (United States / North America)
----------- snip ---------------

[root]# cat zapata.conf
[trunkgroups]
[channels]
language=en
context=from-zaptel
signalling=fxs_ks
rxwink=300              ; Atlas seems to use long (250ms) winks
;
; Whether or not to do distinctive ring detection on FXO lines
;
;usedistinctiveringdetection=yes

usecallerid=yes
hidecallerid=no
callwaiting=yes
usecallingpres=yes
callwaitingcallerid=yes
threewaycalling=yes
transfer=yes
cancallforward=yes
callreturn=yes
echocancel=yes
echocancelwhenbridged=no
echotraining=800
rxgain=0.0
txgain=0.0
group=0
callgroup=1
pickupgroup=1
immediate=no
useincomingcalleridonzaptransfer=yes
busycount=4
callprogress = yes

;faxdetect=both
;faxdetect=incoming
;faxdetect=outgoing
;faxdetect=no

;Include genzaptelconf configs
#include zapata-auto.conf

group=1

;Include AMP configs
#include zapata_additional.conf

Anderson Ling

2006-Jun-07 21:37 UTC

head link

[Asterisk-Users] HELP!!!! Weird TDM2406E unable to bridge all outgoing calls.

Looks like no body know this> Hi all,
> I have TDM2406E with 24FXO ports connecting to 10 POTS line sitting in 
> my office. the out going calls symptom like when called party pickup 
> the phone but the calling party still hearing the ring tone from the 
> IP phone.
> Please light me up. it been many sleepless night by googling around 
> trying to get the right answers.
>
> The digium card running on Intel 915G chipset. Below are my zaptel 
> configurations.
> asterisk version: 1.2.9.1
> Zaptel Version: 1.2.6 Echo Canceller: KB1
> # Span 1: WCTDM/0 "Wildcard TDM2400P Prototype Board 1"
> fxsks=1
> fxsks=2
> fxsks=3
> fxsks=4
> fxsks=5
>    |
>    |
> fxsks=21
> fxsks=22
> fxsks=23
> fxsks=24
>
> # Global data
> loadzone        = us
> defaultzone     = us
>
> [root#] lspci -vb
>
> 06:00.0 Ethernet controller: Digium, Inc. Wildcard TDM2400P (rev 11)
>        Subsystem: Digium, Inc. Wildcard TDM2400P
>        Flags: bus master, medium devsel, latency 32, IRQ 3
>        I/O ports at b800
>        Memory at ff520000 (32-bit, non-prefetchable)
>        Expansion ROM at ff500000 [disabled]
>        Capabilities: [c0] Power Management version 2
>
> [root#] dmesg
>
> --------snip -----------
> Zapata Telephony Interface Registered on major 196
> Zaptel Version: 1.2.6 Echo Canceller: KB1
> PCI: Found IRQ 3 for device 0000:06:00.0
> PCI Config reg is 02900117
> WCTDM2400P: New Reg: fe590000!
> Detected REG0: 00000100
> Detected REG1: 00007849
> Detected REG2: 0000001d
> (pre) Reg fc is 50000027
> (post) Reg fc is 50000024
> Detected REG2: 0000ffff
> wctdm2400p: reg is a04c0004
> Resetting the modules...
> During Resetting the modules...
> After resetting the modules...
> Port 1: Installed -- AUTO FXO (MALAYSIA mode)
> Port 2: Installed -- AUTO FXO (MALAYSIA mode)
> Port 3: Installed -- AUTO FXO (MALAYSIA mode)
> Port 4: Installed -- AUTO FXO (MALAYSIA mode)
> Port 5: Installed -- AUTO FXO (MALAYSIA mode)
> Port 6: Installed -- AUTO FXO (MALAYSIA mode)
> Port 7: Installed -- AUTO FXO (MALAYSIA mode)
> Port 8: Installed -- AUTO FXO (MALAYSIA mode)
> Port 9: Installed -- AUTO FXO (MALAYSIA mode)
> Port 10: Installed -- AUTO FXO (MALAYSIA mode)
> Port 11: Installed -- AUTO FXO (MALAYSIA mode)
> Port 12: Installed -- AUTO FXO (MALAYSIA mode)
> Port 13: Installed -- AUTO FXO (MALAYSIA mode)
> Port 14: Installed -- AUTO FXO (MALAYSIA mode)
> Port 15: Installed -- AUTO FXO (MALAYSIA mode)
> Port 16: Installed -- AUTO FXO (MALAYSIA mode)
> Port 17: Installed -- AUTO FXO (MALAYSIA mode)
> Port 18: Installed -- AUTO FXO (MALAYSIA mode)
> Port 19: Installed -- AUTO FXO (MALAYSIA mode)
> Port 20: Installed -- AUTO FXO (MALAYSIA mode)
> Port 21: Installed -- AUTO FXO (MALAYSIA mode)
> Port 22: Installed -- AUTO FXO (MALAYSIA mode)
> Port 23: Installed -- AUTO FXO (MALAYSIA mode)
> Port 24: Installed -- AUTO FXO (MALAYSIA mode)
> VPM Revision: 01
> VPM: U-law mode
> VPM: DTMF threshold set to 1250
> VPM: Present and operational (Rev B)
> Found a Wildcard TDM: Wildcard TDM2400P Prototype (24 modules)
> Registered tone zone 0 (United States / North America)
> ----------- snip ---------------
>
> [root]# cat zapata.conf
> [trunkgroups]
> [channels]
> language=en
> context=from-zaptel
> signalling=fxs_ks
> rxwink=300              ; Atlas seems to use long (250ms) winks
> ;
> ; Whether or not to do distinctive ring detection on FXO lines
> ;
> ;usedistinctiveringdetection=yes
>
> usecallerid=yes
> hidecallerid=no
> callwaiting=yes
> usecallingpres=yes
> callwaitingcallerid=yes
> threewaycalling=yes
> transfer=yes
> cancallforward=yes
> callreturn=yes
> echocancel=yes
> echocancelwhenbridged=no
> echotraining=800
> rxgain=0.0
> txgain=0.0
> group=0
> callgroup=1
> pickupgroup=1
> immediate=no
> useincomingcalleridonzaptransfer=yes
> busycount=4
> callprogress = yes
>
> ;faxdetect=both
> ;faxdetect=incoming
> ;faxdetect=outgoing
> ;faxdetect=no
>
> ;Include genzaptelconf configs
> #include zapata-auto.conf
>
> group=1
>
> ;Include AMP configs
> #include zapata_additional.conf
>
>
> _______________________________________________
> --Bandwidth and Colocation provided by Easynews.com --
>
> Asterisk-Users mailing list
> To UNSUBSCRIBE or update options visit:
>   http://lists.digium.com/mailman/listinfo/asterisk-users
>
>

Time Bandit

2006-Jun-07 22:03 UTC

head link

[Asterisk-Users] HELP!!!! Weird TDM2406E unable to bridge all outgoing calls.

> Looks like no body know this
I think your problem is right there in zapata.conf :> > callprogress = yesset it to no. Asterisk think that the other end as not answered yet.
If you stay on the line (ignoring the ringing) you will be
disconnected after you dial timeout parameter.

hth

Tzafrir Cohen

2006-Jun-07 22:09 UTC

head link

[Asterisk-Users] HELP!!!! Weird TDM2406E unable to bridge all outgoing calls.

On Wed, Jun 07, 2006 at 02:46:41PM +0800, Anderson Ling
wrote:> Hi all,
> I have TDM2406E with 24FXO ports connecting to 10 POTS line sitting in 
> my office. the out going calls symptom like when called party pickup the 
> phone but the calling party still hearing the ring tone from the IP phone.
> Please light me up. it been many sleepless night by googling around 
> trying to get the right answers.
First off, your post does not include the complete chan_zap
configuration: zapata_auto and zapata_additional are still missing.

Also: what do you see in the CLI as the output of the cmmand 'show
channes' when there is such a call?
> 
> The digium card running on Intel 915G chipset. Below are my zaptel 
> configurations.
> asterisk version: 1.2.9.1
> Zaptel Version: 1.2.6 Echo Canceller: KB1
> # Span 1: WCTDM/0 "Wildcard TDM2400P Prototype Board 1"
> fxsks=1
> fxsks=2
> fxsks=3
> fxsks=4
> fxsks=5
>    |
>    |
> fxsks=21
> fxsks=22
> fxsks=23
> fxsks=24
> 
> # Global data
> loadzone        = us
> defaultzone     = us
> 
> [root#] lspci -vb
> 
> 06:00.0 Ethernet controller: Digium, Inc. Wildcard TDM2400P (rev 11)
>        Subsystem: Digium, Inc. Wildcard TDM2400P
>        Flags: bus master, medium devsel, latency 32, IRQ 3
>        I/O ports at b800
>        Memory at ff520000 (32-bit, non-prefetchable)
>        Expansion ROM at ff500000 [disabled]
>        Capabilities: [c0] Power Management version 2
> 
> [root#] dmesg
> 
> --------snip -----------
> Zapata Telephony Interface Registered on major 196
> Zaptel Version: 1.2.6 Echo Canceller: KB1
> PCI: Found IRQ 3 for device 0000:06:00.0
> PCI Config reg is 02900117
> WCTDM2400P: New Reg: fe590000!
> Detected REG0: 00000100
> Detected REG1: 00007849
> Detected REG2: 0000001d
> (pre) Reg fc is 50000027
> (post) Reg fc is 50000024
> Detected REG2: 0000ffff
> wctdm2400p: reg is a04c0004
> Resetting the modules...
> During Resetting the modules...
> After resetting the modules...
> Port 1: Installed -- AUTO FXO (MALAYSIA mode)
> Port 2: Installed -- AUTO FXO (MALAYSIA mode)
> Port 3: Installed -- AUTO FXO (MALAYSIA mode)
> Port 4: Installed -- AUTO FXO (MALAYSIA mode)
> Port 5: Installed -- AUTO FXO (MALAYSIA mode)
> Port 6: Installed -- AUTO FXO (MALAYSIA mode)
> Port 7: Installed -- AUTO FXO (MALAYSIA mode)
> Port 8: Installed -- AUTO FXO (MALAYSIA mode)
> Port 9: Installed -- AUTO FXO (MALAYSIA mode)
> Port 10: Installed -- AUTO FXO (MALAYSIA mode)
> Port 11: Installed -- AUTO FXO (MALAYSIA mode)
> Port 12: Installed -- AUTO FXO (MALAYSIA mode)
> Port 13: Installed -- AUTO FXO (MALAYSIA mode)
> Port 14: Installed -- AUTO FXO (MALAYSIA mode)
> Port 15: Installed -- AUTO FXO (MALAYSIA mode)
> Port 16: Installed -- AUTO FXO (MALAYSIA mode)
> Port 17: Installed -- AUTO FXO (MALAYSIA mode)
> Port 18: Installed -- AUTO FXO (MALAYSIA mode)
> Port 19: Installed -- AUTO FXO (MALAYSIA mode)
> Port 20: Installed -- AUTO FXO (MALAYSIA mode)
> Port 21: Installed -- AUTO FXO (MALAYSIA mode)
> Port 22: Installed -- AUTO FXO (MALAYSIA mode)
> Port 23: Installed -- AUTO FXO (MALAYSIA mode)
> Port 24: Installed -- AUTO FXO (MALAYSIA mode)
> VPM Revision: 01
> VPM: U-law mode
> VPM: DTMF threshold set to 1250
> VPM: Present and operational (Rev B)
> Found a Wildcard TDM: Wildcard TDM2400P Prototype (24 modules)
> Registered tone zone 0 (United States / North America)
> ----------- snip ---------------
> 
> [root]# cat zapata.conf
> [trunkgroups]
> [channels]
> language=en
> context=from-zaptel
> signalling=fxs_ks
> rxwink=300              ; Atlas seems to use long (250ms) winks
> ;
> ; Whether or not to do distinctive ring detection on FXO lines
> ;
> ;usedistinctiveringdetection=yes
> 
> usecallerid=yes
> hidecallerid=no
> callwaiting=yes
> usecallingpres=yes
> callwaitingcallerid=yes
> threewaycalling=yes
> transfer=yes
> cancallforward=yes
> callreturn=yes
> echocancel=yes
> echocancelwhenbridged=no
> echotraining=800
> rxgain=0.0
> txgain=0.0
> group=0
> callgroup=1
> pickupgroup=1
> immediate=no
> useincomingcalleridonzaptransfer=yes
> busycount=4
> callprogress = yes
> 
> ;faxdetect=both
> ;faxdetect=incoming
> ;faxdetect=outgoing
> ;faxdetect=no
> 
> ;Include genzaptelconf configs
> #include zapata-auto.conf
> 
> group=1
> 
> ;Include AMP configs
> #include zapata_additional.conf
> 
> 
> _______________________________________________
> --Bandwidth and Colocation provided by Easynews.com --
> 
> Asterisk-Users mailing list
> To UNSUBSCRIBE or update options visit:
>   http://lists.digium.com/mailman/listinfo/asterisk-users
> 
-- 
Tzafrir Cohen      sip:tzafrir@local.xorcom.com
icq#16849755       iax:tzafrir@local.xorcom.com
+972-50-7952406           
tzafrir.cohen@xorcom.com  http://www.xorcom.com

El Flynn

2006-Jun-07 22:31 UTC

head link

[Asterisk-Users] HELP!!!! Weird TDM2406E unable to bridge all outgoing calls.

Anderson Ling wrote:> Hi all,
> I have TDM2406E with 24FXO ports connecting to 10 POTS line sitting in 
> my office. the out going calls symptom like when called party pickup the 
> phone but the calling party still hearing the ring tone from the IP phone.
> Please light me up. it been many sleepless night by googling around 
> trying to get the right answers.
> 
> [root]# cat zapata.conf
<snip>> callgroup=1
> pickupgroup=1
> immediate=no
> useincomingcalleridonzaptransfer=yes
> busycount=4
> callprogress = yes
> 
You might not want to use callprogress, as this is more related to US type of 
call progress analysis. The tones are different in Malaysia.

Flynn

Anderson Ling

2006-Jun-08 22:24 UTC

head link

[Asterisk-Users] HELP!!!! Weird TDM2406E unable to bridge all outgoing calls.

Hi Flynn,
Thanks for your reply, after changing the callprogress =no the zap lines 
are working fine now.
Thank you very much.

anderson

El Flynn wrote:> Anderson Ling wrote:
>> Hi all,
>> I have TDM2406E with 24FXO ports connecting to 10 POTS line sitting 
>> in my office. the out going calls symptom like when called party 
>> pickup the phone but the calling party still hearing the ring tone 
>> from the IP phone.
>> Please light me up. it been many sleepless night by googling around 
>> trying to get the right answers.
>>
>> [root]# cat zapata.conf
> <snip>
>> callgroup=1
>> pickupgroup=1
>> immediate=no
>> useincomingcalleridonzaptransfer=yes
>> busycount=4
>> callprogress = yes
>>
>
> You might not want to use callprogress, as this is more related to US 
> type of call progress analysis. The tones are different in Malaysia.
>
> Flynn
>
>
>
>

Reasonably Related Threads

Search for more reasonably related threads

asterisk users - Jun 2006 - HELP!!!! Weird TDM2406E unable to bridge all outgoing calls.

[Asterisk-Users] HELP!!!! Weird TDM2406E unable to bridge all outgoing calls.

[Asterisk-Users] HELP!!!! Weird TDM2406E unable to bridge all outgoing calls.

[Asterisk-Users] HELP!!!! Weird TDM2406E unable to bridge all outgoing calls.

[Asterisk-Users] HELP!!!! Weird TDM2406E unable to bridge all outgoing calls.

[Asterisk-Users] HELP!!!! Weird TDM2406E unable to bridge all outgoing calls.

[Asterisk-Users] HELP!!!! Weird TDM2406E unable to bridge all outgoing calls.

Reasonably Related Threads