similar to: module load order for Junghanns qozap and TDM card

Hi, we are trying to install Junghann's quadBRI into Dell PowerEdge 2800 system without success. I don't know if the issue can be that Junghann's card fits 32-bit slot and Dell PE 2800 has only 3 PCI-X 64-bit slots. Can this be an issue? We get "CRC errors for HDLC frame" when the card is initialized. Any idea what can be wrong? 1/ We use latest bristuff packages. 2/

I installed the QuadBri card in my * server. I'm installing * on a RedHat 9 server I run the install.sh file. So far no problems. If I try to start /sbin/ztcfg -v -c /etc/zaptel.conf I will see the following error: Zaptel Configuration ====================== SPAN 1: CCS/ AMI Build-out: 399-533 feet (DSX-1) SPAN 2: CCS/ AMI Build-out: 399-533 feet (DSX-1) SPAN 3: CCS/ AMI Build-out:

Hi all, We need help with our SuSe9.2 asterisk box We have one QuadBRI and one TDM40B in an ASUS pundit R-2 barebone. We have downloaded the bristuff (0.2.0-RC7j) and installed it without problems. once we downloaded and compiled asterisk, zaptel and all other stuff, the module installation succed in this order: modprobe zaptel modprobe qozap modprobe wcfsx then the ztcfg output this: Zaptel

- I'm not a Linux user i'm trying to get in it ... - Fedora core 1 - QuadBRI card bought from junghanns.net - We want to use the card in TE mode to connect to the TELCO - Downloaded BRISTUFF0.0.2(stable) latest from junghanss.net/asterisk - followed the instructions on voip-info.org - compiled everything still got the error when "make load" in qozap : insmod ./qozap.o

Hi all, this time with the complete configuration files... We need help with our SuSe9.2 asterisk box We have one QuadBRI and one TDM40B in an ASUS pundit R-2 barebone. We have downloaded the bristuff (0.2.0-RC7j) and installed it without problems. once we downloaded and compiled asterisk, zaptel and all other stuff, the module installation succed in this order: modprobe zaptel modprobe qozap

Hi List, I'm setting up a system with one TDM400P (2*FXO + 2 * FXS) and one Junghanns QuadBRI on a Fedora Core 6 (Kernel 2.6.20-1.2944.fc6). I'm using the bristuff-0.3.0-PRE-1y-e kit. It download zaptel-1.2.16, libpri-1.2.4 and asterisk-1.2.17 When it's the time for ztcfg to do its job it complains with <ZT_SPANCONFIG failed on span 2: No such device or address (6)>

Hi all, is it possible to bridge a call between a Junghanns quadBRI card and a TDM400 in the same server? It should be I think, -- I am trying this and when an incoming call comes in, it hangs both up at the moment the bridge is attempted (and a subsequent 'qozap: dropped audio' error is show in the /var/log/messages) Any thoughts appreciated -- I've seen posts, but no clear

Hi everybody I hope that somebody can help me with the following .... I have 2 quadbri cards 2 - 1t0 cards 1 pabx alcatel 4200 I would like to connect my asterisk to the alcatel , I installed bristuff 0.3.0-1p , loaded the zaphfc driver in NT mode configured zaptel and zapata , it works great. then I removed the 1 t0 card, added the quadbri loaded qozap : insmod qozap.ko ports=15 ( 4 ports

Hi all, i'm trying to install Asterisk with Junghanns QuadBri ISDN card: I have followed all the instructions, and when I run "|ztcfg -tvv" I get | | Zaptel Configuration ======================| SPAN 1: CCS/ AMI Build-out: 399-533 feet (DSX-1) Channel map: Channel 01: Individual Clear channel (Default) (Slaves: 01) Channel 02: Individual Clear channel (Default) (Slaves: 02)

Hi, I'm trying to dial from one Asterisk box to a Patton 4638 BRI gateway. I'm only getting this : [May 8 15:08:24] WARNING[16797]: app_dial.c:1547 dial_exec_full: Unable to create channel of type 'DAHDI' (cause 0 - Unknown) My setup is : Asterisk 1.6.1.18 libpri 1.4.10.2 1 Junghanns QuadBRI PCI-E express with : - driver

Hi, I have an asterisk box with a QuadBRI. I am close to make it work like I want: Incoming calls to SIP are OK, outgoing calls are quiet working thanks to Michael Sandee advices. My real problem is that my * box is freezing very often when I probe qozap (bri-stuff 0.0.2). I have tried two distribs (Debian Kernel 2.6, Mandrake 9.1 Kernel 2.4) and it always work for a few minutes and freezes. At

Hi All I have a Junghanns BRI 4 port installed where only the first channel of each line is working i.e. channels 1 and 4 work but 2 and 5 don't. Our config is the same on this box as 15 other similar installations where all works well. the only error I see is in /var/log/messages: Jun 28 15:49:31 pbxct kernel: qozap: CRC error for HDLC frame on card 1 (cardID 0) S/T port 2 Jun 28 15:51:27

Good day all Is there a fix for these errors yet for the junghanns cards Jul 26 17:15:05 pbx1 kernel: qozap: dropped audio card 1 cardid 0 bytes 6 z1 1 z2 107 Jul 26 17:15:18 pbx1 kernel: qozap: dropped audio card 1 cardid 0 bytes 6 z1 10 z2 116 Jul 26 17:15:18 pbx1 kernel: qozap: dropped audio card 1 cardid 0 bytes 5 z1 118 z2 97 Jul 26 17:16:33 pbx1 kernel: qozap: dropped audio card 1 cardid

Hello everybody, I've got Asterisk 1.2.4 running with two Junghanns QuadBRI cards using the qozap driver from bristuff 0.3.0-PRE-1l. One of the cards is running in TE mode, the other one in NT mode. Whenever I call into an empty MeetMe conference room on one of the NT ports or via SIP and hang up the call during the "you are currently the only participant in this conference"

Hi, In my 1.6.1.18 with dahdi 2.2.1.1, I've got : # dahdi_hardware pci:0000:01:0a.0 qozap- 1397:16b8 Junghanns OctoBRI ISDN card Does it mean I should download and use qozap or is it a bug in Dahdi ? Regards -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20100412/de87e46e/attachment.htm

Hi everyone. We have a problem here... Hope somebody can give us some hints. We have a HP ProLiant DL180 G6 Server with a Debian/Lenny sytem. Asterisk 1.4.21.2 (1.4.21.2~dfsg-3+lenny1) with zaptel (1.4.11) and libpri (1.4.3) is installed. There is a QuadBRI-Card installed: # lspci -vv -s 06:04.0 06:04.0 ISDN controller: Cologne Chip Designs GmbH ISDN network Controller [HFC-4S] (rev 01)

Hi, I'm using a revision 6822-enabled Dahdi-Tools (see https://issues.asterisk.org/view.php?id=13897) with a Junghanns QuadBRI. 1. Do I still need qozap driver ? If positive, how is it recommended to get it ? 2. Which line should be included in /etc/dahdi/modules to have the appropriate driver loaded ? 3. The process I'm planning to use is : A- Hand edit /etc/dadhi/modules,

Hi there, I am attempting to set up a simple BRI and SIP based platform using * with the quadbri card (it's not sharing an IRQ). I enclose my zaptel and zapata.conf files. For the inital test I'm simply trying to connect to the * demo menu. The drivers compile (with a few warning that I believe aren't important - see attachments). chan_zap comiles with the warning: chan_zap.c:

Hi, I'm trying to connect quadbri between powered ISDN phone and ISDN line: ISDN <---1---> TE - * - NT <--2--> Phone I use quadbri, suse 9.2 and latest 0.2.0-RC7k bristuff. I've used sample settings provided with package, but do get strange error (I think that I have wrong setting for P2P or P2MP setting and cables 1 and 2). If I connect phone to ISDN with straight cable

Hello, I recently bought a Junghanns Octobri Card. I have some problems with this card to make outbound calls but I can receive calls. I have 3 lines to PSTN and 3 lines to my existing PBX FRANCE TELECOM <-- OctoBRI --> Asterisk 1.2.4-BRIstuffed-0.3.0-PRE-1h <-- OctoBRI --> PABX e-Generis <----> ISDN Phones |