Displaying 20 results from an estimated 101 matches for "setup_zap".
2005 Apr 19
2
Installed ztdummy, Asterisk doesnt work anymore
...ot; again. Before all this, Asterisk worked
perfectly fine, incoming and outgoing connections worked, everything did
its job (except the MeetMe of course). But now I get the following errors
when starting up Asterisk:
[ Booting.....................Apr 19 11:07:28 WARNING[6237]:
chan_zap.c:9615 setup_zap: Ignoring switchtype
Apr 19 11:07:28 WARNING[6237]: chan_zap.c:9615 setup_zap: Ignoring pridialplan
Apr 19 11:07:28 WARNING[6237]: chan_zap.c:9615 setup_zap: Ignoring overlapdial
Apr 19 11:07:28 ERROR[6237]: chan_zap.c:9436 setup_zap: Unknown signalling
method 'bri_cpe_ptmp'
Apr 19 11:07:2...
2006 Oct 13
3
Switchtype,Signalling,rxwink warnings
When I reload the asterisk I get the following warnings:
Oct 13 08:29:17 WARNING[10170]: chan_zap.c:10874 setup_zap: Ignoring
switchtype
Oct 13 08:29:17 WARNING[10170]: chan_zap.c:10874 setup_zap: Ignoring
signalling
Oct 13 08:29:17 WARNING[10170]: chan_zap.c:10874 setup_zap: Ignoring rxwink
Everything works fine as far as I know, I can dial and complete calls.
So why am I getting this warning. Is there an...
2005 May 30
2
Error in Zapata Config?
When I reload the config, I see this error in the CLI. However, I don't see
what I have done wrong:
== Parsing '/etc/asterisk/zapata.conf': Found
May 30 16:38:42 WARNING[12630]: chan_zap.c:10088 setup_zap: Ignoring
signalling
-- Reconfigured channel 1, FXO Kewlstart signalling
May 30 16:38:42 WARNING[12630]: chan_zap.c:10088 setup_zap: Ignoring
signalling
-- Reconfigured channel 2, FXO Kewlstart signalling
May 30 16:38:42 WARNING[12630]: chan_zap.c:10088 setup_zap: Ignoring
signalling
--...
2004 Dec 23
1
ignoring signalling
I reloaded my asterisk and found some red lines flushing by. When I
stopped it I see:
WARNING[21481]: cahn_zap.c:9773 setup_zap: Ignoring signalling
WARNING[21481]: cahn_zap.c:9773 setup_zap: Ignoring echocancelwhenbridge
WARNING[21481]: cahn_zap.c:9773 setup_zap: Ignoring echotraining
Reconfigure channel 1, FXO Kewlstart signalling
Reconfigure channel 2, FXO Kewlstart signalling
WARNING[21481]: cahn_zap.c:9773 setup_zap:...
2005 Jan 09
2
TE110P error
...inux,zaptel,libpti and asterisk
I coped over my zaptel.conf and zapata.conf from a previous E100P config
But when I try to start asterisk it gives error not bying able to load
zap channles:
== Parsing '/etc/asterisk/zapata.conf': Found
Jan 10 08:17:18 WARNING[-1084595552]: chan_zap.c:9308 setup_zap:
Ignoring switchtype
Jan 10 08:17:18 ERROR[-1084595552]: chan_zap.c:9131 setup_zap: Unknown
signalling method 'pri_cpe'
Jan 10 08:17:18 ERROR[-1084595552]: chan_zap.c:8789 setup_zap:
Signalling must be specified before any channels are.
Jan 10 08:17:18 WARNING[-1084595552]: loader.c:334 ast...
2005 Jun 20
1
Unable to reconfigure channel
...problem with the cvs head zaptel library: I cannot update my
zapata.conf into asterisk when I issue the reload command from the CLI
prompt; only when I stop and restart the asterisk service.
The system sends the following message:
Jun 20 09:49:14 WARNING[3754]: chan_zap.c:10364 setup_zap:
Ignoring switchtype
Jun 20 09:49:14 WARNING[3754]: chan_zap.c:10364 setup_zap: Ignoring
signalling
-- Reconfigured channel 1, FXS Kewlstart signalling
-- Reconfigured channel 2, FXS Kewlstart signalling
-- Reconfigured channel 3, FXS Kewlstart signalling
Jun 20 09:49:14 ERROR[3754...
2006 May 09
0
problem with hang up with TDM31B
Hy,
I'm working with asterisk 1.2.4 and zaptel 1.2.4
With these version an the options in zapata.conf:
answeronpolarityswitch=yes
hanguponpolarityswitch=yes
I don't detect polarityswitch. When asterisk reloads I see in CLI:
May 10 00:44:27 WARNING[14639]: chan_zap.c:10876 setup_zap: Ignoring
answeronpolarityswitch
May 10 00:44:27 WARNING[14639]: chan_zap.c:10876 setup_zap: Ignoring
hanguponpolarityswitch
May 10 00:44:27 WARNING[14639]: chan_zap.c:10876 setup_zap: Ignoring
signalling
May 10 00:44:27 WARNING[14639]: chan_zap.c:10876 setup_zap: Ignoring
usercallerid
-- Recon...
2006 Jun 29
2
Sangoma card A101 Card troubles.
...e sangoma tech people have ignored my emails
about this.
All the installation of wanpipe seems to go ok, and zaptel. it all installed
compiled and does all the wanpipe hwprobe exactly as documented.
Asterisk compiled ok, but when I run it give me
Jun 27 11:12:18 ERROR[10528]: chan_zap.c:10614 setup_zap: Unknown
signalling method 'pri_cpe'
Jun 27 11:12:18 ERROR[10528]: chan_zap.c:10239 setup_zap: Signalling
must be specified before any channels are.
Am I right in thinking that's it's something to do with libpri?
Mark
2006 Nov 22
1
Zaptel error
...== Parsing '/etc/asterisk/agents.conf': Found
-- Reloading module 'chan_local.so' (Local Proxy Channel)
-- Reloading module 'chan_zap.so' (Zapata Telephony w/PRI)
== Parsing '/etc/asterisk/zapata.conf': Found
Nov 22 15:43:23 WARNING[14623]: chan_zap.c:10874 setup_zap: Ignoring
switchtype
Nov 22 15:43:23 WARNING[14623]: chan_zap.c:10874 setup_zap: Ignoring
signalling
Nov 22 15:43:23 WARNING[14623]: chan_zap.c:10874 setup_zap: Ignoring rxwink
-- Reloading module 'chan_sip.so' (Session Initiation Protocol (SIP))
-- Reloading module 'chan_mgcp.s...
2004 Sep 30
0
Oops, a seg fault =(
...'4000' at 4000@192.168.0.202:5060 for 1800
-- SIP Seeding '4001' at 4001@192.168.0.21:5060 for 3600
[New Thread 98311 (LWP 28292)]
...[New Thread 114696 (LWP 28293)]
[New Thread 131081 (LWP 28294)]
.[New Thread 147466 (LWP 28295)]
Sep 30 10:51:07 WARNING[16384]: chan_zap.c:9567 setup_zap: Ignoring
loadzone
Sep 30 10:51:07 WARNING[16384]: chan_zap.c:9567 setup_zap: Ignoring
loadzone
Sep 30 10:51:07 WARNING[16384]: chan_zap.c:9567 setup_zap: Ignoring
loadzone
Sep 30 10:51:07 WARNING[16384]: chan_zap.c:9567 setup_zap: Ignoring
loadzone
Sep 30 10:51:07 WARNING[16384]: chan_zap.c:95...
2006 Jan 05
3
TE110p and pri_cpe signalling not recognized
...9;m using this on FC4 and I compile with
linux26 as well checked I on the udev configs.
zttool and ztcfg both indicate that the card is ready.
But when I try to "load chan_zap.so" then I get the following
Unable to load module chan_zap.so
Jan 5 21:43:33 ERROR[6808]: chan_zap.c:10546 setup_zap: Unknown
signalling method 'pri_cpe'
Jan 5 21:43:33 ERROR[6808]: chan_zap.c:10171 setup_zap: Signalling must
be specified before any channels are.
Jan 5 21:43:33 WARNING[6808]: loader.c:414 __load_resource:
chan_zap.so: load_module failed, returning -1
My config is here below.
TIA
Arna...
2005 Jun 14
2
ERROR[5539]: chan_zap.c:9750 setup_zap: Unable to load config zapata.conf
Hi,
I have this error, I have a digium card TE110P Tiger3xx
When I'm load the dirvers by this command modprobe wcte11xp I got this
error
"Notice: Configuration file is /etc/zaptel.conf
line 0: Unable to open master device '/dev/zap/ctl'
1 error(s) detected
FATAL: Error running install command for wct1xxp
"
when I'm Lunch the command ztcfg -vv
I got this error.
2005 Mar 24
0
NetHDLC + PRI
Is it possible to run NETHDLC and PRI signaling on the same 4 port T405P
card?
This is what I get when I try to start asterisk:
== Parsing '/etc/asterisk/zapata.conf': Found
Mar 24 10:48:53 ERROR[2368]: chan_zap.c:9435 setup_zap: Unknown signalling
method 'pri_cpe'
Mar 24 10:48:53 WARNING[2368]: chan_zap.c:9614 setup_zap: Ignoring
switchtype
Mar 24 10:48:53 WARNING[2368]: chan_zap.c:9614 setup_zap: Ignoring
pridialplan
Mar 24 10:48:53 ERROR[2368]: chan_zap.c:9077 setup_zap: Signalling must be
specified before an...
2006 Feb 21
0
asterisk 1.2.4 doesn't detect the PSTN hang up
...ave the 1.2.4 asterisk version and 1.2.3 zaptel version. I've heart
that this asterisk's version detects correctly de hang up of PSTN, but
in my case this thing doesn't happen.
Moreover, my asterisk sends the next messages in the CLI:
Feb 21 15:03:13 WARNING[10363]: chan_zap.c:10876 setup_zap: Ignoring
signalling
Feb 21 15:03:13 WARNING[10363]: chan_zap.c:10876 setup_zap: Ignoring
answeronpolarityswitch
Feb 21 15:03:13 WARNING[10363]: chan_zap.c:10876 setup_zap: Ignoring
hanguponpolarityswitch
Feb 21 15:03:13 WARNING[10363]: chan_zap.c:10876 setup_zap: Ignoring
signalling
-- Rec...
2006 Dec 10
5
TDM2400
I have one TDM2404E digium card on asterisk box, after configuring the
zaptel and zapata configuration files, I am getting these errors when
reloading asterisk:
ast_unregister_indication_country: Removed default indication country 'us'
setup_zap: Ignoring signalling
setup_zap: Ignoring answeronpolarityswitch
unable to recognize channel 13-5
what is the reason for that?
Thanks,
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20061210/27f50fd3/atta...
2006 Mar 13
2
Unknown signalling method 'pri_cpe'
...Driver)
[chan_mgcp.so] => (Media Gateway Control Protocol (MGCP))
== MGCP Listening on 0.0.0.0:2727
== Using TOS bits 0
== Registered channel type 'MGCP' (Media Gateway Control Protocol
(MGCP))
[chan_zap.so] => (Zapata Telephony)
Mar 13 20:44:26 ERROR[10829]: chan_zap.c:10598 setup_zap: Unknown
signalling method 'pri_cpe'
Mar 13 20:44:26 ERROR[10829]: chan_zap.c:10223 setup_zap: Signalling
must be specified before any channels are.
Mar 13 20:44:26 WARNING[10829]: loader.c:414 __load_resource:
chan_zap.so: load_module failed, returning -1
Mar 13 20:44:26 WARNING[10829]: lo...
2007 Mar 07
1
Asterisk Registering to other SIP servers.
...Debugging enabled
*CLI> reload
Mar 7 13:23:12 NOTICE[17748]: cdr.c:1193 do_reload: CDR simple logging
enabled.
Mar 7 13:23:12 NOTICE[17748]: indications.c:505
ast_unregister_indication_country: Removed default indication country 'us'
Mar 7 13:23:12 WARNING[17748]: chan_zap.c:11029 setup_zap: Ignoring
signalling
Mar 7 13:23:12 WARNING[17748]: chan_zap.c:11029 setup_zap: Ignoring
signalling
*CLI> Mar 7 13:23:12 NOTICE[17759]: chan_sip.c:5465 sip_reregister: --
Re-registration for 18474201111@192.168.2.94
REGISTER 12 headers, 0 lines
Reliably Transmitting (no NAT) to 192.168...
2004 May 28
1
* will not load, after latest CVS install
...000 Hz -- sound may be choppy
May 28 13:59:42 WARNING[147466]: chan_oss.c:238 sound_thread: Read error on sound device: Resource temporarily unavailable
[chan_phone.so] => (Linux Telephony API Support)
[chan_zap.so] => (Zapata Telephony w/PRI)
May 28 13:59:42 WARNING[16384]: chan_zap.c:8030 setup_zap: Ignoring usercallerid
May 28 13:59:42 WARNING[16384]: chan_zap.c:704 zt_open: Unable to specify channel 1: No such device or address
May 28 13:59:42 ERROR[16384]: chan_zap.c:5499 mkintf: Unable to open channel 1: No such device or address
here = 0, tmp->channel = 1, channel = 1
May 28 13:59:42...
2003 Dec 29
4
asterisk crash
...ng seemed to go fine however now when
I attempt to start asterisk, it says ok but it seems to be immediately
crashing. The following messages are displayed in my
/var/log/asterisk/messages file for the time right around the crash:
Dec 29 10:09:37 WARNING[1074395872]: File chan_zap.c, Line 7341
(setup_zap): Ignoring rxwink
Dec 29 10:09:37 ERROR[1074395872]: File chan_zap.c, Line 5159 (mkintf):
Unable to get span status: Inappropriate ioctl for device
Dec 29 10:09:37 ERROR[1074395872]: File chan_zap.c, Line 7081 (setup_zap):
Unable to register channel '1-23'
Dec 29 10:09:37 WARNING[10743958...
2004 Dec 10
2
Asterisk 1.0.3 - Signaling on E100P.
...;/etc/asterisk/zapata.conf': Found
-- Registered channel 1, FXO Kewlstart signalling
-- Registered channel 2, FXO Kewlstart signalling
-- Registered channel 3, FXS Kewlstart signalling
-- Registered channel 4, FXS Kewlstart signalling
Dec 11 13:27:48 ERROR[1555]: chan_zap.c:9422 setup_zap: Unknown
signalling method 'pri_net'
Dec 11 13:27:48 ERROR[1555]: chan_zap.c:6209 mkintf: Signalling
requested is FXS Kewlstart but line is in PRI Signalling signalling
Dec 11 13:27:48 ERROR[1555]: chan_zap.c:9141 setup_zap: Unable to
register channel '5-19'
Dec 11 13:27:48 WARNI...