hi everyone,
i''ve managed to install xen on sid and sarge, using this useful howto:
http://www.debian-administration.org/articles/320
i''ve got my virtual machine to startup, but networking doesnt really
work!
my setup is as follows:
i have a router/gateway 192.168.1.1
my base host (moya) is 192.168.1.4
my virtual server (test18) is 192.168.1.18
from the virtual server, i can ping the base host and from the base
host i can ping the server. however, when i try and ping the gateway,
or anywhere else from the vitual server i get:
"From 192.168.1.18 icmp_seq=1 Destination Host Unreachable"
i also tried installing on sid and got exactly the same problem. i''m
not trying to do any fancy networking, just to get it working "out of
the box" :)
here is some info from moya (base host):
/etc/network/interfaces
--------------------------------
hamish@moya:~$ cat /etc/network/interfaces
# This file describes the network in
terfaces available on your system
# and how to activate them. For more information, see interfaces(5).
# The loopback network interface
auto lo
iface lo inet loopback
# The primary network interface
auto eth0
iface eth0 inet static
address 192.168.1.4
netmask 255.255.255.0
network 192.168.1.0
broadcast 192.168.1.255
gateway 192.168.1.1
# dns-* options are implemented by the resolvconf package, if installed
dns-nameservers 210.55.12.1
route
-------
moya:/home/hamish# route
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
localnet * 255.255.255.0 U 0 0 0 eth0
default 192.168.1.1 0.0.0.0 UG 0 0 0 eth0
ifconfig
----------
moya:/home/hamish# ifconfig
eth0 Link encap:Ethernet HWaddr 00:13:72:FC:C0:66
inet addr:192.168.1.4 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::213:72ff:fefc:c066/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:2783 errors:0 dropped:0 overruns:0 frame:0
TX packets:738 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:196151 (191.5 KiB) TX bytes:70241 (68.5 KiB)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:8 errors:0 dropped:0 overruns:0 frame:0
TX packets:8 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:560 (560.0 b) TX bytes:560 (560.0 b)
peth0 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF
inet6 addr: fe80::fcff:ffff:feff:ffff/64 Scope:Link
UP BROADCAST RUNNING NOARP MULTICAST MTU:1500 Metric:1
RX packets:2732 errors:0 dropped:0 overruns:0 frame:0
TX packets:755 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:204077 (199.2 KiB) TX bytes:76453 (74.6 KiB)
Interrupt:16
vif0.0 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF
inet6 addr: fe80::fcff:ffff:feff:ffff/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:738 errors:0 dropped:0 overruns:0 frame:0
TX packets:2788 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:70241 (68.5 KiB) TX bytes:196537 (191.9 KiB)
vif4.0 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF
inet6 addr: fe80::fcff:ffff:feff:ffff/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:35 errors:0 dropped:0 overruns:0 frame:0
TX packets:174 errors:0 dropped:140 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:1638 (1.5 KiB) TX bytes:10466 (10.2 KiB)
xenbr0 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF
inet6 addr: fe80::200:ff:fe00:0/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:2246 errors:0 dropped:0 overruns:0 frame:0
TX packets:5 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:107032 (104.5 KiB) TX bytes:378 (378.0 b)
/etc/xen-tools/xen-tools.conf
-----------------------------------------
moya:/home/hamish# cat /etc/xen-tools/xen-tools.conf
#
# /etc/xen-tools/xen-tools.conf
#
# Global configuration file for the scripts included with Xen-tools.
#
# Values may be set here so they don''t need to be used upon the
# command line.
#
# e.g. --hostname=bob becomes ''hostname = bob''.
# --fs=ext3 becomes ''fs = ext3''.
#
#
#
##
# Output directory. Images are stored beneath this directory, one
# subdirectory per hostname.
##
dir = /home/xen
##
# If you don''t wish to use loopback images, stored beneath the
directory
# specified above with ''dir'' then you may give an LVM volume
name
# instead:
#
##
# volume = xen-volume
##
# Disk and Sizing options.
##
size = 2Gb # Disk image size.
memory = 128Mb # Memory size
swap = 128Mb # Swap size
fs = ext3 # use EXT3 filesystems
dist = sarge # Default distribution to install.
##
# Networking setup values.
##
#
# Uncomment these if you wish to use a static address via the --ip flag.
#
gateway = 192.168.1.1
netmask = 255.255.255.0
#
# Uncomment this if you wish the images to use DHCP
#
# dhcp = 1
##
# Misc options
##
#
# Uncomment the following line if you wish to disable the caching
# of downloaded .deb files.
#
# cache = no
#
#
# Uncomment the following line if you wish to interactively setup
# a new root password for images.
#
# passwd = 1
#
# Default kernel for the virtual servers
#
kernel = /boot/xen-linux-2.6.12.6-xen
#
# Default mirror for debootstrap
#
mirror = http://ftp.us.debian.org/debian/
#
# Uncomment if you wish newly created images to boot automatically.
#
# boot = 1
command to create xen virtual server
-----------------------------------------------------
xen-create-image --ip=192.168.1.18 --hostname=test18
here is some info from the virtual server:
/etc/network/interfaces
--------------------------------
test18:~# cat /etc/network/interfaces
# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).
# The loopback network interface
auto lo
iface lo inet loopback
# The primary network interface
auto eth0
iface eth0 inet static
address 192.168.1.18
gateway 192.168.1.1
netmask 255.255.255.0
route
-------
test18:~# route
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
192.168.1.0 * 255.255.255.0 U 0 0 0 eth0
default 192.168.1.1 0.0.0.0 UG 0 0 0 eth0
ifconfig
----------
test18:~# ifconfig
eth0 Link encap:Ethernet HWaddr 00:16:3E:7F:CB:D4
inet addr:192.168.1.18 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::216:3eff:fe7f:cbd4/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:322 errors:0 dropped:0 overruns:0 frame:0
TX packets:41 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:19958 (19.4 KiB) TX bytes:1890 (1.8 KiB)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:14 errors:0 dropped:0 overruns:0 frame:0
TX packets:14 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:1284 (1.2 KiB) TX bytes:1284 (1.2 KiB)
any help on this would be much appreciated! :)
thanks,
hamish
_______________________________________________
Xen-users mailing list
Xen-users@lists.xensource.com
http://lists.xensource.com/xen-users
Can you please try this in your main server moya? route add default gw 192.168.0.1 dev xenbr0 route del default gw 192.168.0.1 dev eth0 pinunki wrote:>hi everyone, > >i''ve managed to install xen on sid and sarge, using this useful howto: >http://www.debian-administration.org/articles/320 > >i''ve got my virtual machine to startup, but networking doesnt really work! > >my setup is as follows: >i have a router/gateway 192.168.1.1 >my base host (moya) is 192.168.1.4 >my virtual server (test18) is 192.168.1.18 > >from the virtual server, i can ping the base host and from the base >host i can ping the server. however, when i try and ping the gateway, >or anywhere else from the vitual server i get: >"From 192.168.1.18 icmp_seq=1 Destination Host Unreachable" > >i also tried installing on sid and got exactly the same problem. i''m >not trying to do any fancy networking, just to get it working "out of >the box" :) > >here is some info from moya (base host): > >/etc/network/interfaces >-------------------------------- >hamish@moya:~$ cat /etc/network/interfaces ># This file describes the network in >terfaces available on your system ># and how to activate them. For more information, see interfaces(5). > ># The loopback network interface >auto lo >iface lo inet loopback > ># The primary network interface >auto eth0 >iface eth0 inet static > address 192.168.1.4 > netmask 255.255.255.0 > network 192.168.1.0 > broadcast 192.168.1.255 > gateway 192.168.1.1 > # dns-* options are implemented by the resolvconf package, if installed > dns-nameservers 210.55.12.1 > > >route >------- >moya:/home/hamish# route >Kernel IP routing table >Destination Gateway Genmask Flags Metric Ref Use Iface >localnet * 255.255.255.0 U 0 0 0 eth0 >default 192.168.1.1 0.0.0.0 UG 0 0 0 eth0 > > >ifconfig >---------- > >moya:/home/hamish# ifconfig >eth0 Link encap:Ethernet HWaddr 00:13:72:FC:C0:66 > inet addr:192.168.1.4 Bcast:192.168.1.255 Mask:255.255.255.0 > inet6 addr: fe80::213:72ff:fefc:c066/64 Scope:Link > UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 > RX packets:2783 errors:0 dropped:0 overruns:0 frame:0 > TX packets:738 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:0 > RX bytes:196151 (191.5 KiB) TX bytes:70241 (68.5 KiB) > >lo Link encap:Local Loopback > inet addr:127.0.0.1 Mask:255.0.0.0 > inet6 addr: ::1/128 Scope:Host > UP LOOPBACK RUNNING MTU:16436 Metric:1 > RX packets:8 errors:0 dropped:0 overruns:0 frame:0 > TX packets:8 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:0 > RX bytes:560 (560.0 b) TX bytes:560 (560.0 b) > >peth0 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF > inet6 addr: fe80::fcff:ffff:feff:ffff/64 Scope:Link > UP BROADCAST RUNNING NOARP MULTICAST MTU:1500 Metric:1 > RX packets:2732 errors:0 dropped:0 overruns:0 frame:0 > TX packets:755 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:1000 > RX bytes:204077 (199.2 KiB) TX bytes:76453 (74.6 KiB) > Interrupt:16 > >vif0.0 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF > inet6 addr: fe80::fcff:ffff:feff:ffff/64 Scope:Link > UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 > RX packets:738 errors:0 dropped:0 overruns:0 frame:0 > TX packets:2788 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:0 > RX bytes:70241 (68.5 KiB) TX bytes:196537 (191.9 KiB) > >vif4.0 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF > inet6 addr: fe80::fcff:ffff:feff:ffff/64 Scope:Link > UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 > RX packets:35 errors:0 dropped:0 overruns:0 frame:0 > TX packets:174 errors:0 dropped:140 overruns:0 carrier:0 > collisions:0 txqueuelen:0 > RX bytes:1638 (1.5 KiB) TX bytes:10466 (10.2 KiB) > >xenbr0 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF > inet6 addr: fe80::200:ff:fe00:0/64 Scope:Link > UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 > RX packets:2246 errors:0 dropped:0 overruns:0 frame:0 > TX packets:5 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:0 > RX bytes:107032 (104.5 KiB) TX bytes:378 (378.0 b) > > >/etc/xen-tools/xen-tools.conf >----------------------------------------- >moya:/home/hamish# cat /etc/xen-tools/xen-tools.conf ># ># /etc/xen-tools/xen-tools.conf ># ># Global configuration file for the scripts included with Xen-tools. ># ># Values may be set here so they don''t need to be used upon the ># command line. ># ># e.g. --hostname=bob becomes ''hostname = bob''. ># --fs=ext3 becomes ''fs = ext3''. ># ># ># > > >## ># Output directory. Images are stored beneath this directory, one ># subdirectory per hostname. >## >dir = /home/xen > >## ># If you don''t wish to use loopback images, stored beneath the directory ># specified above with ''dir'' then you may give an LVM volume name ># instead: ># >## ># volume = xen-volume > >## ># Disk and Sizing options. >## >size = 2Gb # Disk image size. >memory = 128Mb # Memory size >swap = 128Mb # Swap size >fs = ext3 # use EXT3 filesystems >dist = sarge # Default distribution to install. > > > >## ># Networking setup values. >## > ># ># Uncomment these if you wish to use a static address via the --ip flag. ># >gateway = 192.168.1.1 >netmask = 255.255.255.0 ># ># Uncomment this if you wish the images to use DHCP ># ># dhcp = 1 > > >## ># Misc options >## > ># ># Uncomment the following line if you wish to disable the caching ># of downloaded .deb files. ># ># cache = no ># > ># ># Uncomment the following line if you wish to interactively setup ># a new root password for images. ># ># passwd = 1 > ># ># Default kernel for the virtual servers ># >kernel = /boot/xen-linux-2.6.12.6-xen > > ># ># Default mirror for debootstrap ># >mirror = http://ftp.us.debian.org/debian/ > ># ># Uncomment if you wish newly created images to boot automatically. ># > ># boot = 1 > > >command to create xen virtual server >----------------------------------------------------- > >xen-create-image --ip=192.168.1.18 --hostname=test18 > > >here is some info from the virtual server: > >/etc/network/interfaces >-------------------------------- >test18:~# cat /etc/network/interfaces ># This file describes the network interfaces available on your system ># and how to activate them. For more information, see interfaces(5). > ># The loopback network interface >auto lo >iface lo inet loopback > ># The primary network interface >auto eth0 >iface eth0 inet static > address 192.168.1.18 > gateway 192.168.1.1 > netmask 255.255.255.0 > > >route >------- >test18:~# route >Kernel IP routing table >Destination Gateway Genmask Flags Metric Ref Use Iface >192.168.1.0 * 255.255.255.0 U 0 0 0 eth0 >default 192.168.1.1 0.0.0.0 UG 0 0 0 eth0 > > >ifconfig >---------- >test18:~# ifconfig >eth0 Link encap:Ethernet HWaddr 00:16:3E:7F:CB:D4 > inet addr:192.168.1.18 Bcast:192.168.1.255 Mask:255.255.255.0 > inet6 addr: fe80::216:3eff:fe7f:cbd4/64 Scope:Link > UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 > RX packets:322 errors:0 dropped:0 overruns:0 frame:0 > TX packets:41 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:1000 > RX bytes:19958 (19.4 KiB) TX bytes:1890 (1.8 KiB) > >lo Link encap:Local Loopback > inet addr:127.0.0.1 Mask:255.0.0.0 > inet6 addr: ::1/128 Scope:Host > UP LOOPBACK RUNNING MTU:16436 Metric:1 > RX packets:14 errors:0 dropped:0 overruns:0 frame:0 > TX packets:14 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:0 > RX bytes:1284 (1.2 KiB) TX bytes:1284 (1.2 KiB) > > >any help on this would be much appreciated! :) > >thanks, >hamish > >_______________________________________________ >Xen-users mailing list >Xen-users@lists.xensource.com >http://lists.xensource.com/xen-users > > > >_______________________________________________ Xen-users mailing list Xen-users@lists.xensource.com http://lists.xensource.com/xen-users
Thanks Sadique, but it dodnt work :( Here''s the errors i got: moya:/# route add default gw 192.168.0.1 dev xenbr0 SIOCADDRT: Network is unreachable moya:/# route del default gw 192.168.0.1 dev eth0 SIOCDELRT: No such process also, tried 192.168.1.0 and 1.1 but no luck. On 4/21/06, Sadique <sadique@vanillanetworks.com> wrote:> Can you please try this in your main server moya? > route add default gw 192.168.0.1 dev xenbr0 > route del default gw 192.168.0.1 dev eth0 > > pinunki wrote: > > >hi everyone, > > > >i''ve managed to install xen on sid and sarge, using this useful howto: > >http://www.debian-administration.org/articles/320 > > > >i''ve got my virtual machine to startup, but networking doesnt really work! > > > >my setup is as follows: > >i have a router/gateway 192.168.1.1 > >my base host (moya) is 192.168.1.4 > >my virtual server (test18) is 192.168.1.18 > > > >from the virtual server, i can ping the base host and from the base > >host i can ping the server. however, when i try and ping the gateway, > >or anywhere else from the vitual server i get: > >"From 192.168.1.18 icmp_seq=1 Destination Host Unreachable" > > > >i also tried installing on sid and got exactly the same problem. i''m > >not trying to do any fancy networking, just to get it working "out of > >the box" :) > > > >here is some info from moya (base host): > > > >/etc/network/interfaces > >-------------------------------- > >hamish@moya:~$ cat /etc/network/interfaces > ># This file describes the network in > >terfaces available on your system > ># and how to activate them. For more information, see interfaces(5). > > > ># The loopback network interface > >auto lo > >iface lo inet loopback > > > ># The primary network interface > >auto eth0 > >iface eth0 inet static > > address 192.168.1.4 > > netmask 255.255.255.0 > > network 192.168.1.0 > > broadcast 192.168.1.255 > > gateway 192.168.1.1 > > # dns-* options are implemented by the resolvconf package, if installed > > dns-nameservers 210.55.12.1 > > > > > >route > >------- > >moya:/home/hamish# route > >Kernel IP routing table > >Destination Gateway Genmask Flags Metric Ref Use Iface > >localnet * 255.255.255.0 U 0 0 0 eth0 > >default 192.168.1.1 0.0.0.0 UG 0 0 0 eth0 > > > > > >ifconfig > >---------- > > > >moya:/home/hamish# ifconfig > >eth0 Link encap:Ethernet HWaddr 00:13:72:FC:C0:66 > > inet addr:192.168.1.4 Bcast:192.168.1.255 Mask:255.255.255.0 > > inet6 addr: fe80::213:72ff:fefc:c066/64 Scope:Link > > UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 > > RX packets:2783 errors:0 dropped:0 overruns:0 frame:0 > > TX packets:738 errors:0 dropped:0 overruns:0 carrier:0 > > collisions:0 txqueuelen:0 > > RX bytes:196151 (191.5 KiB) TX bytes:70241 (68.5 KiB) > > > >lo Link encap:Local Loopback > > inet addr:127.0.0.1 Mask:255.0.0.0 > > inet6 addr: ::1/128 Scope:Host > > UP LOOPBACK RUNNING MTU:16436 Metric:1 > > RX packets:8 errors:0 dropped:0 overruns:0 frame:0 > > TX packets:8 errors:0 dropped:0 overruns:0 carrier:0 > > collisions:0 txqueuelen:0 > > RX bytes:560 (560.0 b) TX bytes:560 (560.0 b) > > > >peth0 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF > > inet6 addr: fe80::fcff:ffff:feff:ffff/64 Scope:Link > > UP BROADCAST RUNNING NOARP MULTICAST MTU:1500 Metric:1 > > RX packets:2732 errors:0 dropped:0 overruns:0 frame:0 > > TX packets:755 errors:0 dropped:0 overruns:0 carrier:0 > > collisions:0 txqueuelen:1000 > > RX bytes:204077 (199.2 KiB) TX bytes:76453 (74.6 KiB) > > Interrupt:16 > > > >vif0.0 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF > > inet6 addr: fe80::fcff:ffff:feff:ffff/64 Scope:Link > > UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 > > RX packets:738 errors:0 dropped:0 overruns:0 frame:0 > > TX packets:2788 errors:0 dropped:0 overruns:0 carrier:0 > > collisions:0 txqueuelen:0 > > RX bytes:70241 (68.5 KiB) TX bytes:196537 (191.9 KiB) > > > >vif4.0 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF > > inet6 addr: fe80::fcff:ffff:feff:ffff/64 Scope:Link > > UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 > > RX packets:35 errors:0 dropped:0 overruns:0 frame:0 > > TX packets:174 errors:0 dropped:140 overruns:0 carrier:0 > > collisions:0 txqueuelen:0 > > RX bytes:1638 (1.5 KiB) TX bytes:10466 (10.2 KiB) > > > >xenbr0 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF > > inet6 addr: fe80::200:ff:fe00:0/64 Scope:Link > > UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 > > RX packets:2246 errors:0 dropped:0 overruns:0 frame:0 > > TX packets:5 errors:0 dropped:0 overruns:0 carrier:0 > > collisions:0 txqueuelen:0 > > RX bytes:107032 (104.5 KiB) TX bytes:378 (378.0 b) > > > > > >/etc/xen-tools/xen-tools.conf > >----------------------------------------- > >moya:/home/hamish# cat /etc/xen-tools/xen-tools.conf > ># > ># /etc/xen-tools/xen-tools.conf > ># > ># Global configuration file for the scripts included with Xen-tools. > ># > ># Values may be set here so they don''t need to be used upon the > ># command line. > ># > ># e.g. --hostname=bob becomes ''hostname = bob''. > ># --fs=ext3 becomes ''fs = ext3''. > ># > ># > ># > > > > > >## > ># Output directory. Images are stored beneath this directory, one > ># subdirectory per hostname. > >## > >dir = /home/xen > > > >## > ># If you don''t wish to use loopback images, stored beneath the directory > ># specified above with ''dir'' then you may give an LVM volume name > ># instead: > ># > >## > ># volume = xen-volume > > > >## > ># Disk and Sizing options. > >## > >size = 2Gb # Disk image size. > >memory = 128Mb # Memory size > >swap = 128Mb # Swap size > >fs = ext3 # use EXT3 filesystems > >dist = sarge # Default distribution to install. > > > > > > > >## > ># Networking setup values. > >## > > > ># > ># Uncomment these if you wish to use a static address via the --ip flag. > ># > >gateway = 192.168.1.1 > >netmask = 255.255.255.0 > ># > ># Uncomment this if you wish the images to use DHCP > ># > ># dhcp = 1 > > > > > >## > ># Misc options > >## > > > ># > ># Uncomment the following line if you wish to disable the caching > ># of downloaded .deb files. > ># > ># cache = no > ># > > > ># > ># Uncomment the following line if you wish to interactively setup > ># a new root password for images. > ># > ># passwd = 1 > > > ># > ># Default kernel for the virtual servers > ># > >kernel = /boot/xen-linux-2.6.12.6-xen > > > > > ># > ># Default mirror for debootstrap > ># > >mirror = http://ftp.us.debian.org/debian/ > > > ># > ># Uncomment if you wish newly created images to boot automatically. > ># > > > ># boot = 1 > > > > > >command to create xen virtual server > >----------------------------------------------------- > > > >xen-create-image --ip=192.168.1.18 --hostname=test18 > > > > > >here is some info from the virtual server: > > > >/etc/network/interfaces > >-------------------------------- > >test18:~# cat /etc/network/interfaces > ># This file describes the network interfaces available on your system > ># and how to activate them. For more information, see interfaces(5). > > > ># The loopback network interface > >auto lo > >iface lo inet loopback > > > ># The primary network interface > >auto eth0 > >iface eth0 inet static > > address 192.168.1.18 > > gateway 192.168.1.1 > > netmask 255.255.255.0 > > > > > >route > >------- > >test18:~# route > >Kernel IP routing table > >Destination Gateway Genmask Flags Metric Ref Use Iface > >192.168.1.0 * 255.255.255.0 U 0 0 0 eth0 > >default 192.168.1.1 0.0.0.0 UG 0 0 0 eth0 > > > > > >ifconfig > >---------- > >test18:~# ifconfig > >eth0 Link encap:Ethernet HWaddr 00:16:3E:7F:CB:D4 > > inet addr:192.168.1.18 Bcast:192.168.1.255 Mask:255.255.255.0 > > inet6 addr: fe80::216:3eff:fe7f:cbd4/64 Scope:Link > > UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 > > RX packets:322 errors:0 dropped:0 overruns:0 frame:0 > > TX packets:41 errors:0 dropped:0 overruns:0 carrier:0 > > collisions:0 txqueuelen:1000 > > RX bytes:19958 (19.4 KiB) TX bytes:1890 (1.8 KiB) > > > >lo Link encap:Local Loopback > > inet addr:127.0.0.1 Mask:255.0.0.0 > > inet6 addr: ::1/128 Scope:Host > > UP LOOPBACK RUNNING MTU:16436 Metric:1 > > RX packets:14 errors:0 dropped:0 overruns:0 frame:0 > > TX packets:14 errors:0 dropped:0 overruns:0 carrier:0 > > collisions:0 txqueuelen:0 > > RX bytes:1284 (1.2 KiB) TX bytes:1284 (1.2 KiB) > > > > > >any help on this would be much appreciated! :) > > > >thanks, > >hamish > > > >_______________________________________________ > >Xen-users mailing list > >Xen-users@lists.xensource.com > >http://lists.xensource.com/xen-users > > > > > > > > > >_______________________________________________ Xen-users mailing list Xen-users@lists.xensource.com http://lists.xensource.com/xen-users