zfs discuss - Apr 2010 - cannot set property for ''rpool'': property ''bootfs'' not supported on EFI labeled devices

I am getting the following error, however as you can see below this is a SMI
label...

cannot set property for ''rpool'': property
''bootfs'' not supported on EFI
labeled devices


# zpool get bootfs rpool
NAME PROPERTY VALUE SOURCE
rpool bootfs - default
# zpool set bootfs=rpool/ROOT/s10s_u8wos_08a rpool
cannot set property for ''rpool'': property
''bootfs'' not supported on EFI
labeled devices


partition> pri
Current partition table (original):
Total disk cylinders available: 1989 + 2 (reserved cylinders)

Part Tag Flag Cylinders Size Blocks
0 root wm 0 - 1988 69.93GB (1989/0/0) 146644992
1 unassigned wm 0 0 (0/0/0) 0
2 backup wm 0 - 1988 69.93GB (1989/0/0) 146644992
3 unassigned wm 0 0 (0/0/0) 0
4 unassigned wm 0 0 (0/0/0) 0
5 unassigned wm 0 0 (0/0/0) 0
6 unassigned wm 0 0 (0/0/0) 0
7 unassigned wm 0 0 (0/0/0) 0


Any ideas as to why?

Thanks
-------------- next part --------------
An HTML attachment was scrubbed...
URL:
<http://mail.opensolaris.org/pipermail/zfs-discuss/attachments/20100416/33289a63/attachment.html>

Hi Tony,

Is this on an x86 system?

If so, you might also check whether this disk has a Solaris fdisk
partition or has an EFI fdisk partition.

If it has an EFI fdisk partition then you''ll need to change it to a
Solaris fdisk partition.

See the pointers below.

Thanks,

Cindy

http://www.solarisinternals.com/wiki/index.php/ZFS_Troubleshooting_Guide

Replacing/Relabeling the Root Pool Disk

# fdisk /dev/rdsk/c1t1d0p0
selecting c1t1d0p0
   Total disk size is 8924 cylinders
              Cylinder size is 16065 (512 byte) blocks

                                                Cylinders
       Partition   Status    Type          Start   End   Length    %
       =========   ======    ============  =====   ===   ======   ==           1
EFI               0  8924    8925    100
.
.
.
Enter Selection:
On 04/16/10 11:13, Tony MacDoodle wrote:
> I am getting the following error, however as you can see below this is a 
> SMI label...
> 
> cannot set property for ''rpool'': property
''bootfs'' not supported on EFI
> labeled devices
> 
> 
> # zpool get bootfs rpool
> NAME PROPERTY VALUE SOURCE
> rpool bootfs - default
> # zpool set bootfs=rpool/ROOT/s10s_u8wos_08a rpool
> cannot set property for ''rpool'': property
''bootfs'' not supported on EFI
> labeled devices
> 
> 
> partition> pri
> Current partition table (original):
> Total disk cylinders available: 1989 + 2 (reserved cylinders)
> 
> Part Tag Flag Cylinders Size Blocks
> 0 root wm 0 - 1988 69.93GB (1989/0/0) 146644992
> 1 unassigned wm 0 0 (0/0/0) 0
> 2 backup wm 0 - 1988 69.93GB (1989/0/0) 146644992
> 3 unassigned wm 0 0 (0/0/0) 0
> 4 unassigned wm 0 0 (0/0/0) 0
> 5 unassigned wm 0 0 (0/0/0) 0
> 6 unassigned wm 0 0 (0/0/0) 0
> 7 unassigned wm 0 0 (0/0/0) 0
> 
> 
> Any ideas as to why?
> 
> Thanks
> 
> 
> ------------------------------------------------------------------------
> 
> _______________________________________________
> zfs-discuss mailing list
> zfs-discuss at opensolaris.org
> http://mail.opensolaris.org/mailman/listinfo/zfs-discuss