hi,
After a shutdown my zpool wont go online again, zpool status showed that only
one of five hard drives is online. I tried to export the pool and get it back in
hope of a fix but with no change.
I have replaced the sata cables and even replaced the motherboard but
it''s always showes the same status of the zpool.
#zpool import will show
pool: tank
id: 6529188950165676222
state: UNAVAIL
status: One or more devices are missing from the system.
action: The pool cannot be imported. Attach the missing
devices and try again.
see: http://www.sun.com/msg/ZFS-8000-3C
config:
tank UNAVAIL insufficient replicas
raidz1 UNAVAIL insufficient replicas
c7t1d0 UNAVAIL cannot open
c6t1d0 ONLINE
c6t0d0 UNAVAIL cannot open
c5t1d0 UNAVAIL cannot open
c7t0d0 UNAVAIL cannot open
#format shows
c5t1d0: configured with capacity of 698.60GB
c6t0d0: configured with capacity of 698.60GB
c7t0d0: configured with capacity of 698.60GB
c7t1d0: configured with capacity of 698.60GB
AVAILABLE DISK SELECTIONS:
0. c5t0d0 <DEFAULT cyl 30512 alt 2 hd 255 sec 63>
/pci at 0,0/pci1043,8239 at 5/disk at 0,0
1. c5t1d0 <ATA-WDCWD7500AAKS-0-4G30 cyl 45598 alt 2 hd 255 sec 126>
/pci at 0,0/pci1043,8239 at 5/disk at 1,0
2. c6t0d0 <ATA-WDCWD7500AAKS-0-4G30 cyl 45598 alt 2 hd 255 sec 126>
/pci at 0,0/pci1043,8239 at 5,1/disk at 0,0
3. c6t1d0 <ATA-WDC WD7500AAKS-0-4G30-698.64GB>
/pci at 0,0/pci1043,8239 at 5,1/disk at 1,0
4. c7t0d0 <ATA-WDCWD7500AAKS-0-4G30 cyl 45598 alt 2 hd 255 sec 126>
/pci at 0,0/pci1043,8239 at 5,2/disk at 0,0
5. c7t1d0 <ATA-WDCWD7500AAKS-0-4G30 cyl 45598 alt 2 hd 255 sec 126>
/pci at 0,0/pci1043,8239 at 5,2/disk at 1,0
I find the format a bit strange since it lists the capacity of the four missing
zpool drives but not the hard drive that is online.
Any take on how I can fix this or am I screwed?
Jonas
--
This message posted from opensolaris.org
hi,
After a shutdown my zpool wont go online again, zpool status showed that only
one of five hard drives is online. I tried to export the pool and get it back in
hope of a fix but with no change.
I have replaced the sata cables and even replaced the motherboard but
it''s always showes the same status of the zpool.
#zpool import will show
pool: tank
id: 6529188950165676222
state: UNAVAIL
status: One or more devices are missing from the system.
action: The pool cannot be imported. Attach the missing
devices and try again.
see: http://www.sun.com/msg/ZFS-8000-3C
config:
tank UNAVAIL insufficient replicas
raidz1 UNAVAIL insufficient replicas
c7t1d0 UNAVAIL cannot open
c6t1d0 ONLINE
c6t0d0 UNAVAIL cannot open
c5t1d0 UNAVAIL cannot open
c7t0d0 UNAVAIL cannot open
#format shows
c5t1d0: configured with capacity of 698.60GB
c6t0d0: configured with capacity of 698.60GB
c7t0d0: configured with capacity of 698.60GB
c7t1d0: configured with capacity of 698.60GB
AVAILABLE DISK SELECTIONS:
0. c5t0d0 DEFAULT cyl 30512 alt 2 hd 255 sec 63
/pci at 0,0/pci1043,8239 at 5/disk at 0,0
1. c5t1d0 ATA-WDCWD7500AAKS-0-4G30 cyl 45598 alt 2 hd 255 sec 126
/pci at 0,0/pci1043,8239 at 5/disk at 1,0
2. c6t0d0 ATA-WDCWD7500AAKS-0-4G30 cyl 45598 alt 2 hd 255 sec 126
/pci at 0,0/pci1043,8239 at 5,1/disk at 0,0
3. c6t1d0 ATA-WDC WD7500AAKS-0-4G30-698.64GB
/pci at 0,0/pci1043,8239 at 5,1/disk at 1,0
4. c7t0d0 ATA-WDCWD7500AAKS-0-4G30 cyl 45598 alt 2 hd 255 sec 126
/pci at 0,0/pci1043,8239 at 5,2/disk at 0,0
5. c7t1d0 ATA-WDCWD7500AAKS-0-4G30 cyl 45598 alt 2 hd 255 sec 126
/pci at 0,0/pci1043,8239 at 5,2/disk at 1,0
I find the format a bit strange since it lists the capacity of the four missing
zpool drives but not the hard drive that is online.
Any take on how I can fix this or am I screwed?
Jonas
--
This message posted from opensolaris.org
Hi Jonas, At first sight it looks like your "unopenable" disks were relabeled with SMI label (hence the cyl count on format''s output). Not sure if it is completely safe data wise but you could try to relabel your disks with EFI label (use format -e to access label choice). F. On 10/18/09 20:47, Jonas Nordin wrote:> hi, > > After a shutdown my zpool wont go online again, zpool status showed that only one of five hard drives is online. I tried to export the pool and get it back in hope of a fix but with no change. > I have replaced the sata cables and even replaced the motherboard but it''s always showes the same status of the zpool. > > #zpool import will show > > pool: tank > id: 6529188950165676222 > state: UNAVAIL > status: One or more devices are missing from the system. > action: The pool cannot be imported. Attach the missing > devices and try again. > see: http://www.sun.com/msg/ZFS-8000-3C > config: > > tank UNAVAIL insufficient replicas > raidz1 UNAVAIL insufficient replicas > c7t1d0 UNAVAIL cannot open > c6t1d0 ONLINE > c6t0d0 UNAVAIL cannot open > c5t1d0 UNAVAIL cannot open > c7t0d0 UNAVAIL cannot open > > #format shows > > c5t1d0: configured with capacity of 698.60GB > c6t0d0: configured with capacity of 698.60GB > c7t0d0: configured with capacity of 698.60GB > c7t1d0: configured with capacity of 698.60GB > > > AVAILABLE DISK SELECTIONS: > 0. c5t0d0 DEFAULT cyl 30512 alt 2 hd 255 sec 63 > /pci at 0,0/pci1043,8239 at 5/disk at 0,0 > 1. c5t1d0 ATA-WDCWD7500AAKS-0-4G30 cyl 45598 alt 2 hd 255 sec 126 > /pci at 0,0/pci1043,8239 at 5/disk at 1,0 > 2. c6t0d0 ATA-WDCWD7500AAKS-0-4G30 cyl 45598 alt 2 hd 255 sec 126 > /pci at 0,0/pci1043,8239 at 5,1/disk at 0,0 > 3. c6t1d0 ATA-WDC WD7500AAKS-0-4G30-698.64GB > /pci at 0,0/pci1043,8239 at 5,1/disk at 1,0 > 4. c7t0d0 ATA-WDCWD7500AAKS-0-4G30 cyl 45598 alt 2 hd 255 sec 126 > /pci at 0,0/pci1043,8239 at 5,2/disk at 0,0 > 5. c7t1d0 ATA-WDCWD7500AAKS-0-4G30 cyl 45598 alt 2 hd 255 sec 126 > /pci at 0,0/pci1043,8239 at 5,2/disk at 1,0 > > I find the format a bit strange since it lists the capacity of the four missing zpool drives but not the hard drive that is online. > > Any take on how I can fix this or am I screwed? > > Jonas-- Francois Napoleoni / Sun Support Engineer mail : francois.napoleoni at sun.com phone : +33 (0)1 3403 1707 fax : +33 (0)1 3403 1114
Hi, thank you for replying.
I tried to set a label but I got this.
#format -e
The device does not support mode page 3 or page 4,
or the reported geometry info is invalid.
WARNING: Disk geometry is based on capacity data.
The current rpm value 0 is invalid, adjusting it to 3600
The device does not support mode page 3 or page 4,
or the reported geometry info is invalid.
WARNING: Disk geometry is based on capacity data.
The current rpm value 0 is invalid, adjusting it to 3600
The device does not support mode page 3 or page 4,
or the reported geometry info is invalid.
WARNING: Disk geometry is based on capacity data.
The current rpm value 0 is invalid, adjusting it to 3600
The device does not support mode page 3 or page 4,
or the reported geometry info is invalid.
WARNING: Disk geometry is based on capacity data.
The current rpm value 0 is invalid, adjusting it to 3600
done
c5t1d0: configured with capacity of 698.60GB
c6t0d0: configured with capacity of 698.60GB
c7t0d0: configured with capacity of 698.60GB
c7t1d0: configured with capacity of 698.60GB
AVAILABLE DISK SELECTIONS:
0. c5t0d0 <DEFAULT cyl 30512 alt 2 hd 255 sec 63>
/pci at 0,0/pci1043,8239 at 5/disk at 0,0
1. c5t1d0 <ATA-WDCWD7500AAKS-0-4G30 cyl 45598 alt 2 hd 255 sec 126>
/pci at 0,0/pci1043,8239 at 5/disk at 1,0
2. c6t0d0 <ATA-WDCWD7500AAKS-0-4G30 cyl 45598 alt 2 hd 255 sec 126>
/pci at 0,0/pci1043,8239 at 5,1/disk at 0,0
3. c6t1d0 <ATA-WDC WD7500AAKS-0-4G30-698.64GB>
/pci at 0,0/pci1043,8239 at 5,1/disk at 1,0
4. c7t0d0 <ATA-WDCWD7500AAKS-0-4G30 cyl 45598 alt 2 hd 255 sec 126>
/pci at 0,0/pci1043,8239 at 5,2/disk at 0,0
5. c7t1d0 <ATA-WDCWD7500AAKS-0-4G30 cyl 45598 alt 2 hd 255 sec 126>
/pci at 0,0/pci1043,8239 at 5,2/disk at 1,0
Specify disk (enter its number): 1
selecting c5t1d0
[disk formatted]
Disk not labeled. Label it now? y
Warning: error setting drive geometry.
Warning: error writing VTOC.
Warning: no backup labels
Write label failed
Running fdisk on a disk that is unavailable will show no partition at all.
format> fdisk
No fdisk table exists. The default partition for the disk is:
a 100% "SOLARIS System" partition
Type "y" to accept the default partition, otherwise type
"n" to edit the
partition table.
n
Total disk size is 45600 cylinders
Cylinder size is 32130 (512 byte) blocks
Cylinders
Partition Status Type Start End Length %
========= ====== ============ ===== === ====== ==
WARNING: no partitions are defined!
Doing the same but on the healthy disk.
format> fdisk
Total disk size is 45600 cylinders
Cylinder size is 32130 (512 byte) blocks
Cylinders
Partition Status Type Start End Length %
========= ====== ============ ===== === ====== == 1
EFI 0 45600 45601 100
Looks like the partition information is gone on four of the drives and without
it there is no way to set a label?
Creating a new partition will erase all information of the disk?
--
This message posted from opensolaris.org
On Mon, 19 Oct 2009, Jonas Nordin wrote:> Hi, thank you for replying. > > I tried to set a label but I got this. > > #format -e > > The device does not support mode page 3 or page 4, > or the reported geometry info is invalid. > WARNING: Disk geometry is based on capacity data.Maybe your drives have bad firmware? Certain products (e.g. particular Seagate models) are known to spontaneously expire due to firmware bugs. Bob -- Bob Friesenhahn bfriesen at simple.dallas.tx.us, http://www.simplesystems.org/users/bfriesen/ GraphicsMagick Maintainer, http://www.GraphicsMagick.org/