Chris Andrews
2009-Sep-17 01:37 UTC
[Xen-users] help xen 3.4.1 compile with 2.6.18.8 kernel extra nic missing
Hello, I just compile xen with the xen 2.6.18.8.hg kernel and now when i boot the kernel my eth2 & eth3 is missing but the eth0 and eht1 is working. eth0 & eth1 are boardcom 5708 on the 2900 server board and eht2 and eth2 are Broadcom 5709 pci-x cards. Know i believe all the cards use the same drivers but I''m not sure what going on. When I load the centos xen kernel all the Ethernet cards show up. Here is some info on the server. 08:0d.0 PCI bridge: Broadcom BCM5785 [HT1000] PCI/PCI-X Bridge (rev c0) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+ Stepping- SERR+ FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64, Cache Line Size: 256 bytes Bus: primary=08, secondary=09, subordinate=09, sec-latency=64 I/O behind bridge: 0000f000-00000fff Memory behind bridge: fff00000-000fffff Prefetchable memory behind bridge: 00000000fff00000-0000000000000000 Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B- Capabilities: [90] PCI-X bridge device Secondary Status: 64bit+ 133MHz+ SCD- USC- SCO- SRD- Freq=conv Status: Dev=08:0d.0 64bit+ 133MHz+ SCD- USC- SCO- SRD- Upstream: Capacity=8 CommitmentLimit=8 Downstream: Capacity=8 CommitmentLimit=8 Capabilities: [88] #0d [0000] 08:0e.0 RAID bus controller: Broadcom BCM5785 [HT1000] SATA (Native SATA Mode) (prog-if 05) Subsystem: Dell Unknown device 0205 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+ Stepping- SERR+ FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 64 Interrupt: pin A routed to IRQ 10 Region 0: I/O ports at dcb0 [size=8] Region 1: I/O ports at dca0 [size=4] Region 2: I/O ports at dcb8 [size=8] Region 3: I/O ports at dca4 [size=4] Region 4: I/O ports at dce0 [size=16] Region 5: Memory at ee2fe000 (32-bit, non-prefetchable) [size=8K] [virtual] Expansion ROM at c4000000 [disabled] [size=128K] Capabilities: [60] PCI-X non-bridge device Command: DPERE- ERO- RBC=512 OST=8 Status: Dev=08:0e.0 64bit+ 133MHz+ SCD- USC- DC=simple DMMRBC=512 DMOST=8 DMCRS=32 RSCEM- 266MHz- 533MHz- Capabilities: [90] Power Management version 2 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Capabilities: [a0] Message Signalled Interrupts: 64bit- Queue=0/0 Enable- Address: 00000000 Data: 0000 0b:00.0 Ethernet controller: Broadcom Corporation NetXtreme II BCM5709 Gigabit Ethernet (rev 20) Subsystem: Broadcom Corporation Unknown device 0907 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 10 Region 0: Memory at e4000000 (64-bit, non-prefetchable) [size=32M] Capabilities: [48] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot +,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=1 PME- Capabilities: [50] Vital Product Data Capabilities: [58] Message Signalled Interrupts: 64bit+ Queue=0/3 Enable- Address: 0000000000000000 Data: 0000 Capabilities: [a0] MSI-X: Enable- Mask- TabSize=8 Vector table: BAR=0 offset=0000c000 PBA: BAR=0 offset=0000e000 Capabilities: [ac] Express Endpoint IRQ 0 Device: Supported: MaxPayload 512 bytes, PhantFunc 0, ExtTag- Device: Latency L0s <4us, L1 <64us Device: AtnBtn- AtnInd- PwrInd- Device: Errors: Correctable- Non-Fatal- Fatal+ Unsupported- Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr+ NoSnoop+ Device: MaxPayload 512 bytes, MaxReadReq 512 bytes Link: Supported Speed 2.5Gb/s, Width x4, ASPM L0s L1, Port 0 Link: Latency L0s <4us, L1 <4us Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch- Link: Speed 2.5Gb/s, Width x4 0b:00.1 Ethernet controller: Broadcom Corporation NetXtreme II BCM5709 Gigabit Ethernet (rev 20) Subsystem: Broadcom Corporation Unknown device 0907 Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin B routed to IRQ 10 Region 0: Memory at e6000000 (64-bit, non-prefetchable) [size=32M] Capabilities: [48] Power Management version 3 Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot +,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=1 PME- Capabilities: [50] Vital Product Data Capabilities: [58] Message Signalled Interrupts: 64bit+ Queue=0/3 Enable- Address: 0000000000000000 Data: 0000 Capabilities: [a0] MSI-X: Enable- Mask- TabSize=8 Vector table: BAR=0 offset=0000c000 PBA: BAR=0 offset=0000e000 Capabilities: [ac] Express Endpoint IRQ 0 Device: Supported: MaxPayload 512 bytes, PhantFunc 0, ExtTag- Device: Latency L0s <4us, L1 <64us Device: AtnBtn- AtnInd- PwrInd- Device: Errors: Correctable- Non-Fatal- Fatal+ Unsupported- Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr+ NoSnoop+ Device: MaxPayload 512 bytes, MaxReadReq 512 bytes Link: Supported Speed 2.5Gb/s, Width x4, ASPM L0s L1, Port 0 Link: Latency L0s <4us, L1 <4us Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch- Link: Speed 2.5Gb/s, Width x4 Module Size Used by ipt_MASQUERADE 8192 1 iptable_nat 12164 1 ip_nat 24364 2 ipt_MASQUERADE,iptable_nat xt_state 6784 1 ip_conntrack 62756 4 ipt_MASQUERADE,iptable_nat,ip_nat,xt_state nfnetlink 11848 2 ip_nat,ip_conntrack ipt_REJECT 9984 2 xt_tcpudp 7808 4 iptable_filter 7552 1 ip_tables 25320 2 iptable_nat,iptable_filter x_tables 21640 6 ipt_MASQUERADE,iptable_nat,xt_state,ipt_REJECT,xt_tcpudp,ip_tables bridge 62640 0 ipv6 286816 38 autofs4 27912 2 sunrpc 167112 1 binfmt_misc 17164 1 dm_multipath 23184 0 video 22536 0 thermal 20112 0 sbs 21312 0 processor 43836 1 thermal i2c_ec 9984 1 sbs fan 9736 0 container 9216 0 button 12064 0 battery 15240 0 asus_acpi 22308 0 ac 10120 0 parport_pc 33704 0 lp 18512 0 parport 44812 2 parport_pc,lp tsdev 12928 0 joydev 15232 0 sr_mod 22180 0 cdrom 40232 1 sr_mod usbmouse 10368 0 usbkbd 11904 0 sg 40616 0 i2c_piix4 13964 0 usbhid 52896 0 bnx2 86896 0 i2c_core 27520 2 i2c_ec,i2c_piix4 serio_raw 11908 0 pcspkr 7680 0 megaraid_mbox 37520 0 megaraid_mm 16056 1 megaraid_mbox dm_snapshot 20280 0 dm_zero 6656 0 dm_mirror 25472 0 dm_mod 62672 13 dm_multipath,dm_snapshot,dm_zero,dm_mirror ide_disk 20608 0 sata_svw 13444 0 libata 106144 1 sata_svw megaraid_sas 36280 2 usb_storage 79040 2 sd_mod 25472 4 scsi_mod 152496 7 sr_mod,sg,megaraid_mbox,libata,megaraid_sas,usb_storage,sd_mod ext3 137488 3 jbd 65264 1 ext3 uhci_hcd 28816 0 ohci_hcd 24964 0 ehci_hcd 36744 0 usbcore 140200 8 usbmouse,usbkbd,usbhid,usb_storage,uhci_hcd,ohci_hcd,ehci_hcd _______________________________________________ Xen-users mailing list Xen-users@lists.xensource.com http://lists.xensource.com/xen-users
chris
2009-Sep-17 10:20 UTC
[Xen-users] help xen 3.4.1 compile with 2.6.18.8 kernel extra nic missing
Hello,
I just compile xen with the xen 2.6.18.8.hg kernel and now when i boot
the kernel my eth2 & eth3 is missing but the eth0 and eht1 is working.
eth0 & eth1 are boardcom 5708 on the 2900 server board and eht2 and eth2
are Broadcom 5709 pci-x cards. Know i believe all the cards use the same
drivers but I''m not sure what going on. When I load the centos xen
kernel all the Ethernet cards show up. Here is some info on the server.
08:0d.0 PCI bridge: Broadcom BCM5785 [HT1000] PCI/PCI-X Bridge (rev c0)
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr+
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64, Cache Line Size: 256 bytes
Bus: primary=08, secondary=09, subordinate=09, sec-latency=64
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: fff00000-000fffff
Prefetchable memory behind bridge: 00000000fff00000-0000000000000000
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
Capabilities: [90] PCI-X bridge device
Secondary Status: 64bit+ 133MHz+ SCD- USC- SCO- SRD-
Freq=conv
Status: Dev=08:0d.0 64bit+ 133MHz+ SCD- USC- SCO- SRD-
Upstream: Capacity=8 CommitmentLimit=8
Downstream: Capacity=8 CommitmentLimit=8
Capabilities: [88] #0d [0000]
08:0e.0 RAID bus controller: Broadcom BCM5785 [HT1000] SATA (Native SATA
Mode) (prog-if 05)
Subsystem: Dell Unknown device 0205
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr+
Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at dcb0 [size=8]
Region 1: I/O ports at dca0 [size=4]
Region 2: I/O ports at dcb8 [size=8]
Region 3: I/O ports at dca4 [size=4]
Region 4: I/O ports at dce0 [size=16]
Region 5: Memory at ee2fe000 (32-bit, non-prefetchable) [size=8K]
[virtual] Expansion ROM at c4000000 [disabled] [size=128K]
Capabilities: [60] PCI-X non-bridge device
Command: DPERE- ERO- RBC=512 OST=8
Status: Dev=08:0e.0 64bit+ 133MHz+ SCD- USC- DC=simple
DMMRBC=512
DMOST=8 DMCRS=32 RSCEM- 266MHz- 533MHz-
Capabilities: [90] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [a0] Message Signalled Interrupts: 64bit- Queue=0/0
Enable-
Address: 00000000 Data: 0000
0b:00.0 Ethernet controller: Broadcom Corporation NetXtreme II BCM5709
Gigabit Ethernet (rev 20)
Subsystem: Broadcom Corporation Unknown device 0907
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 10
Region 0: Memory at e4000000 (64-bit, non-prefetchable) [size=32M]
Capabilities: [48] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot
+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data
Capabilities: [58] Message Signalled Interrupts: 64bit+ Queue=0/3
Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [a0] MSI-X: Enable- Mask- TabSize=8
Vector table: BAR=0 offset=0000c000
PBA: BAR=0 offset=0000e000
Capabilities: [ac] Express Endpoint IRQ 0
Device: Supported: MaxPayload 512 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <4us, L1 <64us
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal+ Unsupported-
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr+ NoSnoop+
Device: MaxPayload 512 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x4, ASPM L0s L1, Port 0
Link: Latency L0s <4us, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x4
0b:00.1 Ethernet controller: Broadcom Corporation NetXtreme II BCM5709
Gigabit Ethernet (rev 20)
Subsystem: Broadcom Corporation Unknown device 0907
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort-
<MAbort- >SERR- <PERR-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 10
Region 0: Memory at e6000000 (64-bit, non-prefetchable) [size=32M]
Capabilities: [48] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0+,D1-,D2-,D3hot
+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data
Capabilities: [58] Message Signalled Interrupts: 64bit+ Queue=0/3
Enable-
Address: 0000000000000000 Data: 0000
Capabilities: [a0] MSI-X: Enable- Mask- TabSize=8
Vector table: BAR=0 offset=0000c000
PBA: BAR=0 offset=0000e000
Capabilities: [ac] Express Endpoint IRQ 0
Device: Supported: MaxPayload 512 bytes, PhantFunc 0, ExtTag-
Device: Latency L0s <4us, L1 <64us
Device: AtnBtn- AtnInd- PwrInd-
Device: Errors: Correctable- Non-Fatal- Fatal+ Unsupported-
Device: RlxdOrd+ ExtTag- PhantFunc- AuxPwr+ NoSnoop+
Device: MaxPayload 512 bytes, MaxReadReq 512 bytes
Link: Supported Speed 2.5Gb/s, Width x4, ASPM L0s L1, Port 0
Link: Latency L0s <4us, L1 <4us
Link: ASPM Disabled RCB 64 bytes CommClk- ExtSynch-
Link: Speed 2.5Gb/s, Width x4
Module Size Used by
ipt_MASQUERADE 8192 1
iptable_nat 12164 1
ip_nat 24364 2 ipt_MASQUERADE,iptable_nat
xt_state 6784 1
ip_conntrack 62756 4
ipt_MASQUERADE,iptable_nat,ip_nat,xt_state
nfnetlink 11848 2 ip_nat,ip_conntrack
ipt_REJECT 9984 2
xt_tcpudp 7808 4
iptable_filter 7552 1
ip_tables 25320 2 iptable_nat,iptable_filter
x_tables 21640 6
ipt_MASQUERADE,iptable_nat,xt_state,ipt_REJECT,xt_tcpudp,ip_tables
bridge 62640 0
ipv6 286816 38
autofs4 27912 2
sunrpc 167112 1
binfmt_misc 17164 1
dm_multipath 23184 0
video 22536 0
thermal 20112 0
sbs 21312 0
processor 43836 1 thermal
i2c_ec 9984 1 sbs
fan 9736 0
container 9216 0
button 12064 0
battery 15240 0
asus_acpi 22308 0
ac 10120 0
parport_pc 33704 0
lp 18512 0
parport 44812 2 parport_pc,lp
tsdev 12928 0
joydev 15232 0
sr_mod 22180 0
cdrom 40232 1 sr_mod
usbmouse 10368 0
usbkbd 11904 0
sg 40616 0
i2c_piix4 13964 0
usbhid 52896 0
bnx2 86896 0
i2c_core 27520 2 i2c_ec,i2c_piix4
serio_raw 11908 0
pcspkr 7680 0
megaraid_mbox 37520 0
megaraid_mm 16056 1 megaraid_mbox
dm_snapshot 20280 0
dm_zero 6656 0
dm_mirror 25472 0
dm_mod 62672 13
dm_multipath,dm_snapshot,dm_zero,dm_mirror
ide_disk 20608 0
sata_svw 13444 0
libata 106144 1 sata_svw
megaraid_sas 36280 2
usb_storage 79040 2
sd_mod 25472 4
scsi_mod 152496 7
sr_mod,sg,megaraid_mbox,libata,megaraid_sas,usb_storage,sd_mod
ext3 137488 3
jbd 65264 1 ext3
uhci_hcd 28816 0
ohci_hcd 24964 0
ehci_hcd 36744 0
usbcore 140200 8
usbmouse,usbkbd,usbhid,usb_storage,uhci_hcd,ohci_hcd,ehci_hcd
_______________________________________________
Xen-users mailing list
Xen-users@lists.xensource.com
http://lists.xensource.com/xen-users