If you are trying to configure your interface with something like yast i
believe you have to do the following
shutdown all vm''s think /etc/init.d/xendomains stop will do that or xm
shutdown <domain>
then you need to stop your xen networking bridge with the following
(note this will mean your system is back using eth0 not peth0)
/etc/xen/scripts/network-bridge stop netdev=eth0
do your normal configuration of eth0 with yast, vi or whatever etc now
like you normaly would then when ready restore your xen bridge again
/etc/xen/scripts/network-bridge start netdev=eth0
and finnaly restore your vm domains either using xm or xendomains
Im still new to xen but i remember doing this when i first started
learning on suse so think this may help if you need to configure
interfaces. But im guessing you have another problem as i cant see eth0
listed or any vif interface linked to your xenbr0 bridge so maybe the
driver for your network cards not loaded.
But like i say im still new and learning. I think its worth looking to
make sure your network card driver working as i dont think sit0 is a
networking device as such. I think its stands for simple internet
transition and is somthing to do with encapsulating ipv6 in ipv4
datagrams but this is the first time i seen the sit device so only did a
very quick google search.
Onkar wrote:> I am using OpenSUSE and running Xen 3.1 on it . I am not able to
> connect to the internet. When I try to connect it gives me following
> message :
>
>
> xen network bridge was detected due to the renaming of network interfaces
> by xen bridge script network interfaces should not be configured or
> restarted
> see /usr/share/doc/packages/xen
> /README.SuSE
>
>
>
> # brctl show
> bridge name bridge id STP enabled interfaces
> xenbr0 8000.000000000000 no
> # ifconfig -a
> lo Link encap:Local Loopback
> inet addr:127.0.0.1 <http://127.0.0.1/> Mask: 255.0.0.0
> <http://255.0.0.0/>
> inet6 addr: ::1/128 Scope:Host
> UP LOOPBACK RUNNING MTU:16436 Metric:1
> RX packets:31 errors:0 dropped:0 overruns:0 frame:0
> TX packets:31 errors:0 dropped:0 overruns:0 carrier:0
> collisions:0 txqueuelen:0
> RX bytes:2796 (2.7 Kb) TX bytes:2796 (2.7 Kb)
>
> sit0 Link encap:IPv6-in-IPv4
> NOARP MTU:1480 Metric:1
> RX packets:0 errors:0 dropped:0 overruns:0 frame:0
> TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
> collisions:0 txqueuelen:0
> RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
>
> xenbr0 Link encap:Ethernet HWaddr 00:00:00:00:00:00
> UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
> RX packets:0 errors:0 dropped:0 overruns:0 frame:0
> TX packets:3 errors:0 dropped:0 overruns:0 carrier:0
> collisions:0 txqueuelen:0
> RX bytes:0 (0.0 b) TX bytes:238 (238.0 b)
>
>
> Please help me as I am new to Xen.
>
>
>
>
> Thanks & regards,
> Onkar
> ------------------------------------------------------------------------
>
> _______________________________________________
> Xen-users mailing list
> Xen-users@lists.xensource.com
> http://lists.xensource.com/xen-users
_______________________________________________
Xen-users mailing list
Xen-users@lists.xensource.com
http://lists.xensource.com/xen-users