hi all,
I''ve got the stable xen 3.0.4-1 with the 2.6.16.33 kernel
complied without problems, but in boot I can see this and it doesn''t
bring up the eth0
so I guess I''m missing something in the kernel? the e1000 driver is the
one I need for the network card.
thanks for any hint
rgds
phil
Start Unicode mode
done
Loading console font lat9w-16.psfu -m trivial G0:loadable
done
BLKTAPCTRL[3859]: blktapctrl: v1.0.0
BLKTAPCTRL[3859]: Found driver: [raw image (aio)]
BLKTAPCTRL[3859]: Found driver: [raw image (sync)]
BLKTAPCTRL[3859]: Found driver: [vmware image (vmdk)]
BLKTAPCTRL[3859]: Found driver: [ramdisk image (ram)]
BLKTAPCTRL[3859]: Found driver: [qcow disk (qcow)]
BLKTAPCTRL[3859]: /dev/xen/blktap0 device already exists
device vif0.0 entered promiscuous mode
xenbr0: port 1(vif0.0) entering learning state
xenbr0: topology change detected, propagating
xenbr0: port 1(vif0.0) entering forwarding state
e1000: peth0: e1000_watchdog_task: NIC Link is Up 100 Mbps Full Duplex
device peth0 entered promiscuous mode
xenbr0: port 2(peth0) entering learning state
xenbr0: topology change detected, propagating
xenbr0: port 2(peth0) entering forwarding state
Setting up network interfaces:
lo
lo IP address: 127.0.0.1/8
done
eth0
No configuration found for eth0
unused
veth0
No configuration found for veth0
unused
veth1
No configuration found for veth1
unused
veth2
No configuration found for veth2
unused
veth3
No configuration found for veth3
unused
vif0.0
No configuration found for vif0.0
unused
vif0.1
No configuration found for vif0.1
unused
vif0.2
No configuration found for vif0.2
unused
vif0.3
No configuration found for vif0.3
unused
Waiting for mandatory devices: eth-bus-pci-0000:00:04.0 __NSC__
18 17 16 15 14 13 12 11 10 9 8 6 5 4 3 2 1 0
peth0
No configuration found for peth0
failed
peth0 interface could not be set up until now
failed
Setting up service network . . . . . . . . . . . . . .
failed
___________________________________________________________
All New Yahoo! Mail – Tired of Vi@gr@! come-ons? Let our SpamGuard protect you.
http://uk.docs.yahoo.com/nowyoucan.html
_______________________________________________
Xen-users mailing list
Xen-users@lists.xensource.com
http://lists.xensource.com/xen-users
what''s your eth0 is in a lspci ? regards yves phcolaris a écrit :> hi all, > > I''ve got the stable xen 3.0.4-1 with the 2.6.16.33 kernel > complied without problems, but in boot I can see this and it doesn''t > bring up the eth0 > > so I guess I''m missing something in the kernel? the e1000 driver is the > one I need for the network card. > > thanks for any hint > > rgds > phil > > > Start Unicode mode > done > Loading console font lat9w-16.psfu -m trivial G0:loadable > done > BLKTAPCTRL[3859]: blktapctrl: v1.0.0 > > BLKTAPCTRL[3859]: Found driver: [raw image (aio)] > > BLKTAPCTRL[3859]: Found driver: [raw image (sync)] > > BLKTAPCTRL[3859]: Found driver: [vmware image (vmdk)] > > BLKTAPCTRL[3859]: Found driver: [ramdisk image (ram)] > > BLKTAPCTRL[3859]: Found driver: [qcow disk (qcow)] > > BLKTAPCTRL[3859]: /dev/xen/blktap0 device already exists > > device vif0.0 entered promiscuous mode > xenbr0: port 1(vif0.0) entering learning state > xenbr0: topology change detected, propagating > xenbr0: port 1(vif0.0) entering forwarding state > e1000: peth0: e1000_watchdog_task: NIC Link is Up 100 Mbps Full Duplex > device peth0 entered promiscuous mode > xenbr0: port 2(peth0) entering learning state > xenbr0: topology change detected, propagating > xenbr0: port 2(peth0) entering forwarding state > Setting up network interfaces: > lo > lo IP address: 127.0.0.1/8 > done > eth0 > No configuration found for eth0 > unused > veth0 > No configuration found for veth0 > unused > veth1 > No configuration found for veth1 > unused > veth2 > No configuration found for veth2 > unused > veth3 > No configuration found for veth3 > unused > vif0.0 > No configuration found for vif0.0 > unused > vif0.1 > No configuration found for vif0.1 > unused > vif0.2 > No configuration found for vif0.2 > unused > vif0.3 > No configuration found for vif0.3 > unused > Waiting for mandatory devices: eth-bus-pci-0000:00:04.0 __NSC__ > 18 17 16 15 14 13 12 11 10 9 8 6 5 4 3 2 1 0 > peth0 > No configuration found for peth0 > failed > peth0 interface could not be set up until now > failed > Setting up service network . . . . . . . . . . . . . . > failed > > > > ___________________________________________________________ > All New Yahoo! Mail – Tired of Vi@gr@! come-ons? Let our SpamGuard protect you. http://uk.docs.yahoo.com/nowyoucan.html > > > _______________________________________________ > Xen-users mailing list > Xen-users@lists.xensource.com > http://lists.xensource.com/xen-users > >-- Yves-Gaël Chény Responsable développements techniques Responsable Achats techniques Responsable RH technique 261 route de Clisson 44230 St Sébastien sur Loire Tel : 02 40 97 62 67 - 08 73 77 24 91 http://www.tranquilitsystems.com/ yves-gael.cheny@tranquil-it-systems.fr Tranquil IT Systems . SAS 37 000 ¤ _______________________________________________ Xen-users mailing list Xen-users@lists.xensource.com http://lists.xensource.com/xen-users
hi, in non-xen system # lspci 00:01.0 PCI bridge: Broadcom BCM5785 [HT1000] PCI/PCI-X Bridge 00:02.0 Host bridge: Broadcom BCM5785 [HT1000] Legacy South Bridge 00:02.1 IDE interface: Broadcom BCM5785 [HT1000] IDE 00:02.2 ISA bridge: Broadcom BCM5785 [HT1000] LPC 00:03.0 USB Controller: Broadcom BCM5785 [HT1000] USB (rev 01) 00:03.1 USB Controller: Broadcom BCM5785 [HT1000] USB (rev 01) 00:03.2 USB Controller: Broadcom BCM5785 [HT1000] USB (rev 01) 00:04.0 Ethernet controller: Intel Corporation 82541GI Gigabit Ethernet Controller (rev 05) 00:06.0 VGA compatible controller: XGI Technology Inc. (eXtreme Graphics Innovation) Volari Z7 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 00:19.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:19.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:19.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:19.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 01:0d.0 PCI bridge: Broadcom BCM5785 [HT1000] PCI/PCI-X Bridge (rev c0) 02:03.0 PCI bridge: Intel Corporation 80331 [Lindsay] I/O processor (PCI-X Bridge) (rev 0a) 03:0e.0 RAID bus controller: Areca Technology Corp. ARC-1110 4-Port PCI-X to SATA RAID Controller in xen: # lspci 00:01.0 PCI bridge: Broadcom BCM5785 [HT1000] PCI/PCI-X Bridge 00:02.0 Host bridge: Broadcom BCM5785 [HT1000] Legacy South Bridge 00:02.1 IDE interface: Broadcom BCM5785 [HT1000] IDE 00:02.2 ISA bridge: Broadcom BCM5785 [HT1000] LPC 00:03.0 USB Controller: Broadcom BCM5785 [HT1000] USB (rev 01) 00:03.1 USB Controller: Broadcom BCM5785 [HT1000] USB (rev 01) 00:03.2 USB Controller: Broadcom BCM5785 [HT1000] USB (rev 01) 00:04.0 Ethernet controller: Intel Corporation 82541GI Gigabit Ethernet Controller (rev 05) 00:06.0 VGA compatible controller: XGI Technology Inc. (eXtreme Graphics Innovation) Volari Z7 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 00:19.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:19.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:19.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:19.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 01:0d.0 PCI bridge: Broadcom BCM5785 [HT1000] PCI/PCI-X Bridge (rev c0) 02:03.0 PCI bridge: Intel Corporation 80331 [Lindsay] I/O processor (PCI-X Bridge) (rev 0a) 03:0e.0 RAID bus controller: Areca Technology Corp. ARC-1110 4-Port PCI-X to SATA RAID Controller rgds phil On Tue, 2007-03-27 at 12:53 +0200, Yves-gaël Chény wrote:> what''s your eth0 is in a lspci ? > > regards > yves > > phcolaris a écrit : > > hi all, > > > > I''ve got the stable xen 3.0.4-1 with the 2.6.16.33 kernel > > complied without problems, but in boot I can see this and it doesn''t > > bring up the eth0 > > > > so I guess I''m missing something in the kernel? the e1000 driver is the > > one I need for the network card. > > > > thanks for any hint > > > > rgds > > phil > > > >___________________________________________________________ Copy addresses and emails from any email account to Yahoo! Mail - quick, easy and free. http://uk.docs.yahoo.com/trueswitch2.html _______________________________________________ Xen-users mailing list Xen-users@lists.xensource.com http://lists.xensource.com/xen-users
Yves-gaël Chény
2007-Mar-27 14:41 UTC
Re: [Bulk] Re: [Xen-users] eth0 / device problem in dom0
for 00:04.0 Ethernet controller: Intel Corporation 82541GI Gigabit Ethernet Controller (rev 05) have you the e1000 module with a " lsmod " ? regards yves phcolaris a écrit :> hi, > > in non-xen system > # lspci > 00:01.0 PCI bridge: Broadcom BCM5785 [HT1000] PCI/PCI-X Bridge > 00:02.0 Host bridge: Broadcom BCM5785 [HT1000] Legacy South Bridge > 00:02.1 IDE interface: Broadcom BCM5785 [HT1000] IDE > 00:02.2 ISA bridge: Broadcom BCM5785 [HT1000] LPC > 00:03.0 USB Controller: Broadcom BCM5785 [HT1000] USB (rev 01) > 00:03.1 USB Controller: Broadcom BCM5785 [HT1000] USB (rev 01) > 00:03.2 USB Controller: Broadcom BCM5785 [HT1000] USB (rev 01) > 00:04.0 Ethernet controller: Intel Corporation 82541GI Gigabit Ethernet > Controller (rev 05) > 00:06.0 VGA compatible controller: XGI Technology Inc. (eXtreme Graphics > Innovation) Volari Z7 > 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] > HyperTransport Technology Configuration > 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] > Address Map > 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] > DRAM Controller > 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] > Miscellaneous Control > 00:19.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] > HyperTransport Technology Configuration > 00:19.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] > Address Map > 00:19.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] > DRAM Controller > 00:19.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] > Miscellaneous Control > 01:0d.0 PCI bridge: Broadcom BCM5785 [HT1000] PCI/PCI-X Bridge (rev c0) > 02:03.0 PCI bridge: Intel Corporation 80331 [Lindsay] I/O processor > (PCI-X Bridge) (rev 0a) > 03:0e.0 RAID bus controller: Areca Technology Corp. ARC-1110 4-Port > PCI-X to SATA RAID Controller > > in xen: > # lspci > 00:01.0 PCI bridge: Broadcom BCM5785 [HT1000] PCI/PCI-X Bridge > 00:02.0 Host bridge: Broadcom BCM5785 [HT1000] Legacy South Bridge > 00:02.1 IDE interface: Broadcom BCM5785 [HT1000] IDE > 00:02.2 ISA bridge: Broadcom BCM5785 [HT1000] LPC > 00:03.0 USB Controller: Broadcom BCM5785 [HT1000] USB (rev 01) > 00:03.1 USB Controller: Broadcom BCM5785 [HT1000] USB (rev 01) > 00:03.2 USB Controller: Broadcom BCM5785 [HT1000] USB (rev 01) > 00:04.0 Ethernet controller: Intel Corporation 82541GI Gigabit Ethernet > Controller (rev 05) > 00:06.0 VGA compatible controller: XGI Technology Inc. (eXtreme Graphics > Innovation) Volari Z7 > 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] > HyperTransport Technology Configuration > 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] > Address Map > 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] > DRAM Controller > 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] > Miscellaneous Control > 00:19.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] > HyperTransport Technology Configuration > 00:19.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] > Address Map > 00:19.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] > DRAM Controller > 00:19.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] > Miscellaneous Control > 01:0d.0 PCI bridge: Broadcom BCM5785 [HT1000] PCI/PCI-X Bridge (rev c0) > 02:03.0 PCI bridge: Intel Corporation 80331 [Lindsay] I/O processor > (PCI-X Bridge) (rev 0a) > 03:0e.0 RAID bus controller: Areca Technology Corp. ARC-1110 4-Port > PCI-X to SATA RAID Controller > > > rgds > phil > > On Tue, 2007-03-27 at 12:53 +0200, Yves-gaël Chény wrote: > >> what''s your eth0 is in a lspci ? >> >> regards >> yves >> >> phcolaris a écrit : >> >>> hi all, >>> >>> I''ve got the stable xen 3.0.4-1 with the 2.6.16.33 kernel >>> complied without problems, but in boot I can see this and it doesn''t >>> bring up the eth0 >>> >>> so I guess I''m missing something in the kernel? the e1000 driver is the >>> one I need for the network card. >>> >>> thanks for any hint >>> >>> rgds >>> phil >>> >>> >>> > > > > ___________________________________________________________ > Copy addresses and emails from any email account to Yahoo! Mail - quick, easy and free. http://uk.docs.yahoo.com/trueswitch2.html > >-- Yves-Gaël Chény Responsable développements techniques Responsable Achats techniques Responsable RH technique 261 route de Clisson 44230 St Sébastien sur Loire Tel : 02 40 97 62 67 - 08 73 77 24 91 http://www.tranquilitsystems.com/ yves-gael.cheny@tranquil-it-systems.fr Tranquil IT Systems . SAS 37 000 ¤ _______________________________________________ Xen-users mailing list Xen-users@lists.xensource.com http://lists.xensource.com/xen-users
Peter Fastré
2007-Mar-27 14:47 UTC
Re: [Bulk] Re: [Xen-users] eth0 / device problem in dom0
On 3/27/07, phcolaris <phcolaris@yahoo.co.uk> wrote:> > > 00:04.0 Ethernet controller: Intel Corporation 82541GI Gigabit Ethernet > Controller (rev 05) >I have a recent supermicro server, and the Intel network cards weren''t recognized by the 2.6.16.33 kernel either. You can get an updated driver from http://sourceforge.net/projects/e1000. You can compile the driver as a module, as described in the driver install procedure. If you do that, however, you have to make sure you don''t have the older e1000 driver compiled in your kernel. So recompile your Xen kernel WITHOUT the intel e1000 driver. It took me some time before I had figured that out. You can also replace the driver in the 2.6.16.33-kernel by the files you got from sourceforge. This way, it''s possible to compile the driver in the kernel, if you would like that. Peter _______________________________________________ Xen-users mailing list Xen-users@lists.xensource.com http://lists.xensource.com/xen-users
phcolaris
2007-Mar-27 18:04 UTC
Re: [Bulk] Re: [Bulk] Re: [Xen-users] eth0 / device problem in dom0
well, got the driver, after loading got this
Intel(R) PRO/1000 Network Driver - version 7.4.35
Copyright (c) 1999-2007 Intel Corporation.
GSI 17 sharing vector 0xA0 and IRQ 17
ACPI: PCI Interrupt 0000:00:04.0[A] -> GSI 24 (level, low) -> IRQ 17
e1000: 0000:00:04.0: e1000_probe: (PCI:33MHz:32-bit) 00:e0:81:47:e2:8c
e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
so I believe that its just fine. but the boot is without change :-(
any idea?
thanks
phil
boot log:
Loading console font lat9w-16.psfu -m trivial G0:loadable
done
BLKTAPCTRL[3818]: blktapctrl: v1.0.0
BLKTAPCTRL[3818]: Found driver: [raw image (aio)]
BLKTAPCTRL[3818]: Found driver: [raw image (sync)]
BLKTAPCTRL[3818]: Found driver: [vmware image (vmdk)]
BLKTAPCTRL[3818]: Found driver: [ramdisk image (ram)]
BLKTAPCTRL[3818]: Found driver: [qcow disk (qcow)]
BLKTAPCTRL[3818]: /dev/xen/blktap0 device already exists
device vif0.0 entered promiscuous mode
xenbr0: port 1(vif0.0) entering learning state
xenbr0: topology change detected, propagating
xenbr0: port 1(vif0.0) entering forwarding state
e1000: peth0: e1000_watchdog_task: NIC Link is Up 100 Mbps Full Duplex,
Flow Control: RX
device peth0 entered promiscuous mode
xenbr0: port 2(peth0) entering learning state
xenbr0: topology change detected, propagating
xenbr0: port 2(peth0) entering forwarding state
Setting up network interfaces:
lo
lo IP address: 127.0.0.1/8
done
eth0
No configuration found for eth0
unused
veth0
No configuration found for veth0
unused
veth1
No configuration found for veth1
unused
veth2
No configuration found for veth2
unused
veth3
No configuration found for veth3
unused
vif0.0
No configuration found for vif0.0
unused
vif0.1
No configuration found for vif0.1
unused
vif0.2
No configuration found for vif0.2
unused
vif0.3
No configuration found for vif0.3
unused
Waiting for mandatory devices: eth-bus-pci-0000:00:04.0 __NSC__
18 17 16 15 14 13 12 11 10 9 8 6 5 4 3 2 1 0
peth0
No configuration found for peth0
failed
peth0 interface could not be set up until now
failed
Setting up service network . . . . . . . . . . . . . .
failed
On Tue, 2007-03-27 at 16:47 +0200, Peter Fastré wrote:>
>
> On 3/27/07, phcolaris <phcolaris@yahoo.co.uk> wrote:
>
> 00:04.0 Ethernet controller: Intel Corporation 82541GI Gigabit
> Ethernet
> Controller (rev 05)
>
> I have a recent supermicro server, and the Intel network cards
weren''t
> recognized by the 2.6.16.33 kernel either. You can get an updated
> driver from http://sourceforge.net/projects/e1000.
>
> You can compile the driver as a module, as described in the driver
> install procedure. If you do that, however, you have to make sure you
> don''t have the older e1000 driver compiled in your kernel. So
> recompile your Xen kernel WITHOUT the intel e1000 driver. It took me
> some time before I had figured that out.
> You can also replace the driver in the 2.6.16.33-kernel by the files
> you got from sourceforge. This way, it''s possible to compile the
> driver in the kernel, if you would like that.
>
> Peter
>
>
>
> _______________________________________________
> Xen-users mailing list
> Xen-users@lists.xensource.com
> http://lists.xensource.com/xen-users
___________________________________________________________
Win tickets to the 2006 FIFA World Cup Germany with Yahoo! Messenger.
http://advision.webevents.yahoo.com/fifaworldcup_uk/
_______________________________________________
Xen-users mailing list
Xen-users@lists.xensource.com
http://lists.xensource.com/xen-users