> > Well, i''m using here the qla2340 on several boxes. It works
> > with Xen 2.0 but noch with Xen 3.0. as part of SUSE Linux 10.0:
>
> Interesting. If the driver really doews work flawlessly in
> Xen 2, then I think the culprit has to be interrupt routeing.
>
> Under Xen 3, does /proc/interrupts show you''re receiving
interrupts?
I cannot boot with Xen 3, because my boot device is attached on the
qla controller. Grub, xen.gz, initrd are starting exactly from this
device without any prolem until the qla driver should be loaded. :-(
> Do other devices with high irq numbers appear to be working OK?
No idea how to check it.
Stephan
> > kernel-xen-2.6.13-15
> > kernel-xen-nongpl-2.6.13-15
> > xen-3.0_6715-2
> >
> > System startup with xen kernel fails on detecting the boot
> > device, which is attached to the qla2300 fibre channel host
> > bus adapter.
> >
> > qla2300 0000:05:01.0: Found an ISP2312, irq 185, iobase
> > 0xf8812000 qla2300 0000:05:01.0: Configuring PCI space...
> > qla2300 0000:05:01.0: Configure NVRAM parameters...
> > qla2300 0000:05:01.0: Verifying loaded RISC code...
> > qla2300 0000:05:01.0: Waiting for LIP to complete...
> >
> > Until here it''s alle fine, but then:
> >
> > qla2300 0000:05:01.0: LIP reset occured (f7f7).
> > qla2300 0000:05:01.0: LOOP UP detected (2 Gbps).
> > qla2300 0000:05:01.0: Topology - (F_Port), Host Loop address 0xffff
> > scsi3 : qla2xxx
> > qla2300 0000:04:02.0:
> > QLogic Fibre Channel HBA Driver: 8.01.00b5-k
> > QLogic QLA2340 - 133MHz PCI-X to 2Gb FC, Single Channel
> > ISP2312: PCI-X (100 MHz) @ 0000:05:01.0 hdma+, host#=3,
> > fw=3.03.15 IPX Loading kernel/fs/reiserfs/reiserfs.ko Waiting
> > for device /dev/sda4 to appear: .....not found --- exiting to
> > /bin/sh $
> >
> > With the 2.6.13-15-smp kernel as part of SUSE Linux 10 it
> > goes on without any problem:
> >
> > SCSI device sda: 41943040 512-byte hdwr sectors (21475 MB)
> > SCSI device sda: drive cache: write back SCSI device sda:
> > 41943040 512-byte hdwr sectors (21475 MB) SCSI device sda:
> > drive cache: write back
> > sda: sda1 sda2 sda3 sda4
> > ....etc.
> >
> > Stephan
> >
> >
> > -----Ursprüngliche Nachricht-----
> > Von: The Smoking Man [mailto:datashark@gmail.com]
> > Gesendet: Freitag, 7. Oktober 2005 19:13
> > An: Ian Pratt
> > Cc: xen-devel@lists.xensource.com; Stephan Böni;
> > xen-users@lists.xensource.com
> > Betreff: [Xen-devel] Re: [Xen-users] xen 3.0 boot problem
> >
> >
> > Beein used here the qla2344 on several boxes. works
> > trully fine on gentoo-xensources (vanilla kernel plus xen
> > patches) and (this is what i''m using in production) with suse
> > kotd sources.
> >
> > Bellow is the relevant bootlog...
> >
> > Best regards,
> >
> > [ 6.599201] QLogic Fibre Channel HBA Driver
> > [ 6.599446] ACPI: PCI Interrupt 0000:02:04.0[A] ->
> > GSI 29 (level, low) -> IRQ 29
> > [ 6.599749] qla2300 0000:02:04.0: Found an ISP2312,
> > irq 29, iobase 0xe8804000
> > [ 6.600392] qla2300 0000:02:04.0: Configuring PCI space...
> > [ 6.600687] qla2300 0000:02:04.0: Configure NVRAM
> > parameters...
> > [ 6.685681] qla2300 0000:02:04.0: Verifying loaded
> > RISC code...
> > [ 6.809175] qla2300 0000:02:04.0: Waiting for LIP to
> > complete...
> > [ 27.200114] qla2300 0000:02:04.0: Cable is unplugged...
> > [ 27.200289] scsi0 : qla2xxx
> > [ 27.200579] qla2300 0000:02:04.0:
> > [ 27.200580] QLogic Fibre Channel HBA Driver: 8.00.02b5-k
> > [ 27.200581] QLogic QLA2344 -
> > [ 27.200582] ISP2312: PCI-X (133 MHz) @
> > 0000:02:04.0 hdma+, host#=0, fw=3.03.08 IPX
> > [ 27.201211] ACPI: PCI Interrupt 0000:02:04.1[B] ->
> > GSI 30 (level, low) -> IRQ 30
> > [ 27.201482] qla2300 0000:02:04.1: Found an ISP2312,
> > irq 30, iobase 0xe8806000
> > [ 27.202082] qla2300 0000:02:04.1: Configuring PCI space...
> > [ 27.202369] qla2300 0000:02:04.1: Configure NVRAM
> > parameters...
> > [ 27.287483] qla2300 0000:02:04.1: Verifying loaded
> > RISC code...
> > [ 27.410625] qla2300 0000:02:04.1: Waiting for LIP to
> > complete...
> > [ 47.810115] qla2300 0000:02:04.1: Cable is unplugged...
> > [ 47.810279] scsi1 : qla2xxx
> > [ 47.810504] qla2300 0000:02:04.1:
> > [ 47.810505] QLogic Fibre Channel HBA Driver: 8.00.02b5-k
> > [ 47.810507] QLogic QLA2344 -
> > [ 47.810508] ISP2312: PCI-X (133 MHz) @
> > 0000:02:04.1 hdma+, host#=1, fw=3.03.08 IPX
> > [ 47.811136] ACPI: PCI Interrupt 0000:02:06.0[A] ->
> > GSI 31 (level, low) -> IRQ 31
> > [ 47.811404] qla2300 0000:02:06.0: Found an ISP2312,
> > irq 31, iobase 0xe881a000
> > [ 47.812006] qla2300 0000:02:06.0: Configuring PCI space...
> > [ 47.812295] qla2300 0000:02:06.0: Configure NVRAM
> > parameters...
> > [ 47.897025] qla2300 0000:02:06.0: Verifying loaded
> > RISC code...
> > [ 48.020170] qla2300 0000:02:06.0: Waiting for LIP to
> > complete...
> > [ 68.410104] qla2300 0000:02:06.0: Cable is unplugged...
> > [ 68.410270] scsi2 : qla2xxx
> > [ 68.410514] qla2300 0000:02:06.0:
> > [ 68.410515] QLogic Fibre Channel HBA Driver: 8.00.02b5-k
> > [ 68.410517] QLogic QLA2344 -
> > [ 68.410518] ISP2312: PCI-X (133 MHz) @
> > 0000:02:06.0 hdma+, host#=2, fw=3.03.08 IPX
> > [ 68.411144] ACPI: PCI Interrupt 0000:02:06.1[B] ->
> > GSI 28 (level, low) -> IRQ 28
> > [ 68.411413] qla2300 0000:02:06.1: Found an ISP2312,
> > irq 28, iobase 0xe881c000
> > [ 68.412024] qla2300 0000:02:06.1: Configuring PCI space...
> > [ 68.412311] qla2300 0000:02:06.1: Configure NVRAM
> > parameters...
> > [ 68.497424] qla2300 0000:02:06.1: Verifying loaded
> > RISC code...
> > [ 68.516876] qla2300 0000:02:06.1: Waiting for LIP to
> > complete...
> > [ 69.020063] qla2300 0000:02:06.1: LIP reset occured (f8f7).
> > [ 69.020220] qla2300 0000:02:06.1: LIP occured (f8f7).
> > [ 69.020370] qla2300 0000:02:06.1: LOOP UP detected (2 Gbps).
> > [ 69.020661] qla2300 0000:02:06.1: Topology - (Loop),
> > Host Loop address 0x0
> > [ 69.021595] scsi3 : qla2xxx
> > [ 69.021824] qla2300 0000:02:06.1:
> > [ 69.021825] QLogic Fibre Channel HBA Driver: 8.00.02b5-k
> > [ 69.021826] QLogic QLA2344 -
> > [ 69.021827] ISP2312: PCI-X (133 MHz) @
> > 0000:02:06.1 hdma+, host#=3, fw=3.03.08 IPX
> > [ 69.025082] mice: PS/2 mouse device common for all mice
> > [ 69.025227] md: md driver 0.90.1 MAX_MD_DEVS=256,
> > MD_SB_DISKS=27
> > [ 69.025434] NET: Registered protocol family 2
> > [ 69.025850] Vendor: DotHill Model: SANnet II FC
> > Rev: 327R
> > [ 69.026240] Type: Direct-Access
> > ANSI SCSI revision: 03
> > [ 69.027076] SCSI device sda: 131072 512-byte hdwr
> > sectors (67 MB)
> > [ 69.027919] SCSI device sda: drive cache: write through
> > [ 69.028521] SCSI device sda: 131072 512-byte hdwr
> > sectors (67 MB)
> > [ 69.029354] SCSI device sda: drive cache: write through
> > [ 69.029495] sda: sda1
> > [ 69.030035] Attached scsi disk sda at scsi3, channel
> > 0, id 0, lun 0
> > [ 69.031081] Vendor: DotHill Model: SANnet II FC
> > Rev: 327R
> > [ 69.031466] Type: Direct-Access
> > ANSI SCSI revision: 03
> > [ 69.032195] SCSI device sdb: 2097152 512-byte hdwr
> > sectors (1074 MB)
> > [ 69.032943] SCSI device sdb: drive cache: write through
> > [ 69.033469] SCSI device sdb: 2097152 512-byte hdwr
> > sectors (1074 MB)
> > [ 69.034213] SCSI device sdb: drive cache: write through
> > [ 69.034353] sdb: sdb1
> > [ 69.048548] Attached scsi disk sdb at scsi3, channel
> > 0, id 0, lun 1
> > [ 69.049188] Vendor: DotHill Model: SANnet II FC
> > Rev: 327R
> > [ 69.049573] Type: Direct-Access
> > ANSI SCSI revision: 03
> > [ 69.050305] SCSI device sdc: 12582912 512-byte hdwr
> > sectors (6442 MB)
> > [ 69.051056] SCSI device sdc: drive cache: write through
> > [ 69.051586] SCSI device sdc: 12582912 512-byte hdwr
> > sectors (6442 MB)
> > [ 69.052341] SCSI device sdc: drive cache: write through
> > [ 69.052481] sdc: sdc1
> > [ 69.065097] Attached scsi disk sdc at scsi3, channel
> > 0, id 0, lun 2
> > [ 69.065589] Vendor: DotHill Model: SANnet II FC
> > Rev: 327R
> > [ 69.065973] Type: Direct-Access
> > ANSI SCSI revision: 03
> > [ 69.066583] SCSI device sdd: 12582912 512-byte hdwr
> > sectors (6442 MB)
> > [ 69.067279] SCSI device sdd: drive cache: write through
> > [ 69.067695] SCSI device sdd: 12582912 512-byte hdwr
> > sectors (6442 MB)
> > [ 69.068303] SCSI device sdd: drive cache: write through
> > [ 69.068442] sdd: sdd1
> > [ 69.078452] Attached scsi disk sdd at scsi3, channel
> > 0, id 0, lun 3
> > [ 69.078969] Vendor: DotHill Model: SANnet II FC
> > Rev: 327R
> > [ 69.079355] Type: Direct-Access
> > ANSI SCSI revision: 03
> > [ 69.080403] SCSI device sde: 12582912 512-byte hdwr
> > sectors (6442 MB)
> > [ 69.081042] SCSI device sde: drive cache: write through
> > [ 69.081458] SCSI device sde: 12582912 512-byte hdwr
> > sectors (6442 MB)
> > [ 69.082098] SCSI device sde: drive cache: write through
> > [ 69.082237] sde: sde1
> > [ 69.093087] Attached scsi disk sde at scsi3, channel
> > 0, id 0, lun 4
> > [ 69.093592] Vendor: DotHill Model: SANnet II FC
> > Rev: 327R
> > [ 69.093976] Type: Direct-Access
> > ANSI SCSI revision: 03
> > [ 69.094591] SCSI device sdf: 12582912 512-byte hdwr
> > sectors (6442 MB)
> > [ 69.095206] SCSI device sdf: drive cache: write through
> > [ 69.095615] SCSI device sdf: 12582912 512-byte hdwr
> > sectors (6442 MB)
> > [ 69.096234] SCSI device sdf: drive cache: write through
> > [ 69.096373] sdf: sdf1
> > [ 69.108174] Attached scsi disk sdf at scsi3, channel
> > 0, id 0, lun 5
> > [ 69.108790] Vendor: DotHill Model: SANnet II FC
> > Rev: 327R
> > [ 69.109175] Type: Direct-Access
> > ANSI SCSI revision: 03
> > [ 69.110034] SCSI device sdg: 12582912 512-byte hdwr
> > sectors (6442 MB)
> > [ 69.110638] SCSI device sdg: drive cache: write through
> > [ 69.111046] SCSI device sdg: 12582912 512-byte hdwr
> > sectors (6442 MB)
> > [ 69.111645] SCSI device sdg: drive cache: write through
> > [ 69.111784] sdg: sdg1
> > [ 69.122286] Attached scsi disk sdg at scsi3, channel
> > 0, id 0, lun 6
> > [ 69.122777] Vendor: DotHill Model: SANnet II FC
> > Rev: 327R
> > [ 69.123163] Type: Direct-Access
> > ANSI SCSI revision: 03
> > [ 69.123772] SCSI device sdh: 2097152 512-byte hdwr
> > sectors (1074 MB)
> > [ 69.124377] SCSI device sdh: drive cache: write through
> > [ 69.124789] SCSI device sdh: 2097152 512-byte hdwr
> > sectors (1074 MB)
> > [ 69.125393] SCSI device sdh: drive cache: write through
> > [ 69.125532] sdh: sdh1
> > [ 69.134481] Attached scsi disk sdh at scsi3, channel
> > 0, id 0, lun 7
> > [ 69.134971] Vendor: DotHill Model: SANnet II FC
> > Rev: 327R
> > [ 69.135355] Type: Direct-Access
> > ANSI SCSI revision: 03
> > [ 69.135974] SCSI device sdi: 2097152 512-byte hdwr
> > sectors (1074 MB)
> > [ 69.136577] SCSI device sdi: drive cache: write through
> > [ 69.136994] SCSI device sdi: 2097152 512-byte hdwr
> > sectors (1074 MB)
> > [ 69.137597] SCSI device sdi: drive cache: write through
> > [ 69.137736] sdi: sdi1
> > [ 69.142544] Attached scsi disk sdi at scsi3, channel
> > 0, id 0, lun 8
> > [ 69.143037] Vendor: DotHill Model: SANnet II FC
> > Rev: 327R
> > [ 69.143421] Type: Direct-Access
> > ANSI SCSI revision: 03
> > [ 69.144036] SCSI device sdj: 2097152 512-byte hdwr
> > sectors (1074 MB)
> > [ 69.144635] SCSI device sdj: drive cache: write through
> > [ 69.145044] SCSI device sdj: 2097152 512-byte hdwr
> > sectors (1074 MB)
> > [ 69.145640] SCSI device sdj: drive cache: write through
> > [ 69.145780] sdj:<6>IP: routing cache hash table of
> > 8192 buckets, 64Kbytes
> > [ 69.150433] TCP established hash table entries:
> > 131072 (order: 8, 1048576 bytes)
> > [ 69.151333] TCP bind hash table entries: 65536
> > (order: 7, 524288 bytes)
> > [ 69.151870] TCP: Hash tables configured (established
> > 131072 bind 65536)
> > [ 69.152110] NET: Registered protocol family 1
> > [ 69.153802] unknown partition table
> > [ 69.153959] Attached scsi disk sdj at scsi3, channel
> > 0, id 0, lun 9
> > [ 69.154482] Vendor: DotHill Model: SANnet II FC
> > Rev: 327R
> > [ 69.154867] Type: Direct-Access
> > ANSI SCSI revision: 03
> > [ 69.155484] SCSI device sdk: 2097152 512-byte hdwr
> > sectors (1074 MB)
> > [ 69.156083] SCSI device sdk: drive cache: write through
> > [ 69.156502] SCSI device sdk: 2097152 512-byte hdwr
> > sectors (1074 MB)
> > [ 69.157095] SCSI device sdk: drive cache: write through
> > [ 69.157234] sdk: unknown partition table
> > [ 69.168099] Attached scsi disk sdk at scsi3, channel
> > 0, id 0, lun 10
> >
> >
> >
> >
> >
> > On 10/5/05, Ian Pratt <m+Ian.Pratt@cl.cam.ac.uk> wrote:
> >
> >
> > Has anyone used xen succefully with a qla2300?
> >
> > What machines have this card?
> >
> > Ian
> >
> > > I''ve installed Xen 3.0-devel on SUSE Linux
> > without any problems.
> > > But when i tryed to boot the system, i''ve got
> > a funny problem:
> > >
> > > qla2300 0000:05:01.0: Found an ISP2312, irq
> > 185, iobase
> > > 0xf8812000 qla2300 0000:05:01.0: Configuring
> > PCI space...
> > > qla2300 0000:05:01.0: Configure NVRAM parameters...
> > > qla2300 0000:05: 01.0: Verifying loaded RISC code...
> > > qla2300 0000:05:01.0: Waiting for LIP to complete...
> > >
> > > until here all works fine, but then:
> > >
> > > input: PS/2 Generic Mouse on
> > synaptcs-pt/serio0 qla2300
> > > 0000:05:01.0: LIP reset occured (f7f7).
> > > qla2300 0000:05:01.0: LOOP UP detected (2 Gbps).
> > > qla2300 0000:05:01.0: Topology - (F_Port),
> > Host Loop address 0xffff
> > > scsi3 : qla2xxx
> > > qla2300 0000:04: 02.0:
> > > QLogic Fibre Channel HBA Driver: 8.01.00b5-k
> > > QLogic QLA2340 - 133MHz PCI-X to 2Gb FC,
> > Single Channel
> > > ISP2312: PCI-X (100 MHz) @ 0000:05:01.0
> > hdma+, host#=3,
> > > fw=3.03.15 IPX
> > > Loading kernel/fs/reiserfs/reiserfs.ko
> > > Waiting for device /dev/sda4 to appear:
> > .....not found ---
> > > exiting to /bin/sh $
> > >
> > > if i use the standard (bigsmp) kernel the
> > normal massages are:
> > >
> > > SCSI device sda: 41943040 512-byte hdwr
> > sectors (21475 MB)
> > > SCSI device sda: drive cache: write back SCSI
> > device sda:
> > > 41943040 512-byte hdwr sectors (21475 MB)
> > SCSI device sda:
> > > drive cache: write back
> > > sda: sda1 sda2 sda3 sda4
> > > ....usw.
> > >
> > > Well, my qla2300 has the storage attached not
> > a generic mouse.
> > > Of course it isn''t possible to boot from this
> > mouse. :-(
> >
> >
> >
> > _______________________________________________
> > Xen-users mailing list
> > Xen-users@lists.xensource.com
> > http://lists.xensource.com/xen-users
> >
> >
> >
> >
>
> _______________________________________________
> Xen-devel mailing list
> Xen-devel@lists.xensource.com
> http://lists.xensource.com/xen-devel
>
_______________________________________________
Xen-devel mailing list
Xen-devel@lists.xensource.com
http://lists.xensource.com/xen-devel
