Hi all I got xen-unstable.hg, did a fresh hg pull today(08/01). Then I built and installed xen-unstable. I can boot up Xen and Dom0. (DomU didn''t create.) But a network of Dom0 cannot be connected. How should I do? I use RTL-8139 network card, and 8139too. The following message is shown by "dmesg |tail". =====================================================NETDEV WATCHDOG: eth0: transmit timed out eth0: Transmit timeout, status 0c 0005 c07f media 10. eth0: Tx queue start entry 4 dirty entry 0. eth0: Tx descriptor 0 is 0008a05b. (queue head) eth0: Tx descriptor 1 is 0008a07c. eth0: Tx descriptor 2 is 0008a04e. eth0: Tx descriptor 3 is 0008a05b. eth0: link up, 100Mbps, full-duplex, lpa 0x41E1 ===================================================== So, I checked /proc/interrupts and network interrupts didn''t count. ===================================================== CPU0 1: 0 Phys-irq i8042 8: 0 Phys-irq rtc 9: 0 Phys-irq acpi 12: 0 Phys-irq i8042 14: 3683 Phys-irq ide0 15: 1728 Phys-irq ide1 17: 0 Phys-irq yenta, eth0 18: 0 Phys-irq SiS SI7012, SiS SI7013 Modem, yenta 19: 0 Phys-irq ohci1394 20: 0 Phys-irq ohci_hcd:usb2 21: 0 Phys-irq ohci_hcd:usb3 22: 0 Phys-irq ohci_hcd:usb4 23: 0 Phys-irq ehci_hcd:usb1 256: 0 Dynamic-irq ctrl-if 257: 12811 Dynamic-irq timer0 258: 0 Dynamic-irq resched0 259: 0 Dynamic-irq callfunc0 260: 0 Dynamic-irq console 261: 0 Dynamic-irq net-be-dbg NMI: 0 LOC: 0 ERR: 0 MIS: 0 ===================================================== Why interrupts of eth0 isn''t counted? Could anyone help me. The result of lsmod and ifconfig is put as follows. o lsmod ===================================================== Module Size Used by md5 8448 1 ipv6 292928 8 autofs4 25604 2 rfcomm 52504 0 l2cap 37120 5 rfcomm bluetooth 62468 4 rfcomm,l2cap sunrpc 154308 1 video 20740 0 thermal 18056 0 processor 22944 1 thermal fan 9092 0 button 11024 0 battery 13956 0 ac 9220 0 ohci1394 42420 0 ieee1394 313688 1 ohci1394 yenta_socket 28168 0 rsrc_nonstatic 18816 1 yenta_socket pcmcia_core 58276 2 yenta_socket,rsrc_nonstatic ohci_hcd 23812 0 ehci_hcd 39688 0 i2c_sis96x 10116 0 i2c_core 27264 1 i2c_sis96x snd_intel8x0m 23748 0 snd_intel8x0 38336 0 snd_ac97_codec 87296 2 snd_intel8x0m,snd_intel8x0 snd_seq_dummy 8196 0 snd_seq_oss 41472 0 snd_seq_midi_event 12544 1 snd_seq_oss snd_seq 62480 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi_event snd_seq_device 13580 3 snd_seq_dummy,snd_seq_oss,snd_seq snd_pcm_oss 60704 0 snd_mixer_oss 25088 1 snd_pcm_oss snd_pcm 100228 4 snd_intel8x0m,snd_intel8x0,snd_ac97_codec,snd_pcm_oss snd_timer 31236 2 snd_seq,snd_pcm snd 60260 10 snd_intel8x0m,snd_intel8x0,snd_ac97_codec,snd_seq_oss,snd_seq,snd_seq_device,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer soundcore 14304 1 snd snd_page_alloc 14724 3 snd_intel8x0m,snd_intel8x0,snd_pcm 8139too 33152 0 mii 10240 1 8139too ext3 151048 2 jbd 70552 1 ext3 dm_mod 67748 1 ===================================================== o ifconfig -a ===================================================== eth0 Link encap:Ethernet HWaddr 00:40:D0:34:B8:BC inet addr:10.124.50.61 Bcast:10.124.50.255 Mask:255.255.255.0 inet6 addr: fe80::240:d0ff:fe34:b8bc/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) Interrupt:17 Base address:0xe400 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:14 errors:0 dropped:0 overruns:0 frame:0 TX packets:14 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1148 (1.1 KiB) TX bytes:1148 (1.1 KiB) sit0 Link encap:IPv6-in-IPv4 NOARP MTU:1480 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) veth0 Link encap:Ethernet HWaddr 00:00:00:00:00:00 BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) vif0.0 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) ===================================================== Thanks, AKio _______________________________________________ Xen-users mailing list Xen-users@lists.xensource.com http://lists.xensource.com/xen-users
Hi all I got xen-unstable.hg, did a fresh hg pull today(08/01). Then I built and installed xen-unstable. I can boot up Xen and Dom0. (DomU didn''t create.) But a network of Dom0 cannot be connected. How should I do? I use RTL-8139 network card, and 8139too. The following message is shown by "dmesg |tail". =====================================================NETDEV WATCHDOG: eth0: transmit timed out eth0: Transmit timeout, status 0c 0005 c07f media 10. eth0: Tx queue start entry 4 dirty entry 0. eth0: Tx descriptor 0 is 0008a05b. (queue head) eth0: Tx descriptor 1 is 0008a07c. eth0: Tx descriptor 2 is 0008a04e. eth0: Tx descriptor 3 is 0008a05b. eth0: link up, 100Mbps, full-duplex, lpa 0x41E1 ===================================================== So, I checked /proc/interrupts and network interrupts didn''t count. ===================================================== CPU0 1: 0 Phys-irq i8042 8: 0 Phys-irq rtc 9: 0 Phys-irq acpi 12: 0 Phys-irq i8042 14: 3683 Phys-irq ide0 15: 1728 Phys-irq ide1 17: 0 Phys-irq yenta, eth0 18: 0 Phys-irq SiS SI7012, SiS SI7013 Modem, yenta 19: 0 Phys-irq ohci1394 20: 0 Phys-irq ohci_hcd:usb2 21: 0 Phys-irq ohci_hcd:usb3 22: 0 Phys-irq ohci_hcd:usb4 23: 0 Phys-irq ehci_hcd:usb1 256: 0 Dynamic-irq ctrl-if 257: 12811 Dynamic-irq timer0 258: 0 Dynamic-irq resched0 259: 0 Dynamic-irq callfunc0 260: 0 Dynamic-irq console 261: 0 Dynamic-irq net-be-dbg NMI: 0 LOC: 0 ERR: 0 MIS: 0 ===================================================== Why interrupts of eth0 isn''t counted? Could anyone help me. The result of lsmod and ifconfig is put as follows. o lsmod ===================================================== Module Size Used by md5 8448 1 ipv6 292928 8 autofs4 25604 2 rfcomm 52504 0 l2cap 37120 5 rfcomm bluetooth 62468 4 rfcomm,l2cap sunrpc 154308 1 video 20740 0 thermal 18056 0 processor 22944 1 thermal fan 9092 0 button 11024 0 battery 13956 0 ac 9220 0 ohci1394 42420 0 ieee1394 313688 1 ohci1394 yenta_socket 28168 0 rsrc_nonstatic 18816 1 yenta_socket pcmcia_core 58276 2 yenta_socket,rsrc_nonstatic ohci_hcd 23812 0 ehci_hcd 39688 0 i2c_sis96x 10116 0 i2c_core 27264 1 i2c_sis96x snd_intel8x0m 23748 0 snd_intel8x0 38336 0 snd_ac97_codec 87296 2 snd_intel8x0m,snd_intel8x0 snd_seq_dummy 8196 0 snd_seq_oss 41472 0 snd_seq_midi_event 12544 1 snd_seq_oss snd_seq 62480 5 snd_seq_dummy,snd_seq_oss, snd_seq_midi_event snd_seq_device 13580 3 snd_seq_dummy,snd_seq_oss, snd_seq snd_pcm_oss 60704 0 snd_mixer_oss 25088 1 snd_pcm_oss snd_pcm 100228 4 snd_intel8x0m,snd_intel8x0, snd_ac97_codec,snd_pcm_oss snd_timer 31236 2 snd_seq,snd_pcm snd 60260 10 snd_intel8x0m,snd_intel8x0, snd_ac97_codec,snd_seq_oss,snd_seq,snd_seq_device,snd_pcm_oss, snd_mixer_oss,snd_pcm,snd_timer soundcore 14304 1 snd snd_page_alloc 14724 3 snd_intel8x0m,snd_intel8x0, snd_pcm 8139too 33152 0 mii 10240 1 8139too ext3 151048 2 jbd 70552 1 ext3 dm_mod 67748 1 ===================================================== o ifconfig -a ===================================================== eth0 Link encap:Ethernet HWaddr 00:40:D0:34:B8:BC inet addr:10.124.50.61 Bcast:10.124.50.255 Mask:255. 255.255.0 inet6 addr: fe80::240:d0ff:fe34:b8bc/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) Interrupt:17 Base address:0xe400 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:14 errors:0 dropped:0 overruns:0 frame:0 TX packets:14 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1148 (1.1 KiB) TX bytes:1148 (1.1 KiB) sit0 Link encap:IPv6-in-IPv4 NOARP MTU:1480 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) veth0 Link encap:Ethernet HWaddr 00:00:00:00:00:00 BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) vif0.0 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) ===================================================== Thanks, AKio _______________________________________________ Xen-users mailing list Xen-users@lists.xensource.com http://lists.xensource.com/xen-users
Hi all I got xen-unstable.hg, did a fresh hg pull today(08/01). Then I built and installed xen-unstable. I can boot up Xen and Dom0. (DomU didn''t create.) But a network of Dom0 cannot be connected. How should I do? I use RTL-8139 network card, and 8139too. The following message is shown by "dmesg |tail". =====================================================NETDEV WATCHDOG: eth0: transmit timed out eth0: Transmit timeout, status 0c 0005 c07f media 10. eth0: Tx queue start entry 4 dirty entry 0. eth0: Tx descriptor 0 is 0008a05b. (queue head) eth0: Tx descriptor 1 is 0008a07c. eth0: Tx descriptor 2 is 0008a04e. eth0: Tx descriptor 3 is 0008a05b. eth0: link up, 100Mbps, full-duplex, lpa 0x41E1 ===================================================== So, I checked /proc/interrupts and network interrupts wasn''t counted. ===================================================== CPU0 1: 0 Phys-irq i8042 8: 0 Phys-irq rtc 9: 0 Phys-irq acpi 12: 0 Phys-irq i8042 14: 3683 Phys-irq ide0 15: 1728 Phys-irq ide1 17: 0 Phys-irq yenta, eth0 18: 0 Phys-irq SiS SI7012, SiS SI7013 Modem, yenta 19: 0 Phys-irq ohci1394 20: 0 Phys-irq ohci_hcd:usb2 21: 0 Phys-irq ohci_hcd:usb3 22: 0 Phys-irq ohci_hcd:usb4 23: 0 Phys-irq ehci_hcd:usb1 256: 0 Dynamic-irq ctrl-if 257: 12811 Dynamic-irq timer0 258: 0 Dynamic-irq resched0 259: 0 Dynamic-irq callfunc0 260: 0 Dynamic-irq console 261: 0 Dynamic-irq net-be-dbg NMI: 0 LOC: 0 ERR: 0 MIS: 0 ===================================================== Why interrupts of eth0 isn''t counted? Could anyone help me. The result of lsmod and ifconfig is put as follows. o lsmod ===================================================== Module Size Used by md5 8448 1 ipv6 292928 8 autofs4 25604 2 rfcomm 52504 0 l2cap 37120 5 rfcomm bluetooth 62468 4 rfcomm,l2cap sunrpc 154308 1 video 20740 0 thermal 18056 0 processor 22944 1 thermal fan 9092 0 button 11024 0 battery 13956 0 ac 9220 0 ohci1394 42420 0 ieee1394 313688 1 ohci1394 yenta_socket 28168 0 rsrc_nonstatic 18816 1 yenta_socket pcmcia_core 58276 2 yenta_socket,rsrc_nonstatic ohci_hcd 23812 0 ehci_hcd 39688 0 i2c_sis96x 10116 0 i2c_core 27264 1 i2c_sis96x snd_intel8x0m 23748 0 snd_intel8x0 38336 0 snd_ac97_codec 87296 2 snd_intel8x0m,snd_intel8x0 snd_seq_dummy 8196 0 snd_seq_oss 41472 0 snd_seq_midi_event 12544 1 snd_seq_oss snd_seq 62480 5 snd_seq_dummy,snd_seq_oss, snd_seq_midi_event snd_seq_device 13580 3 snd_seq_dummy,snd_seq_oss, snd_seq snd_pcm_oss 60704 0 snd_mixer_oss 25088 1 snd_pcm_oss snd_pcm 100228 4 snd_intel8x0m,snd_intel8x0, snd_ac97_codec,snd_pcm_oss snd_timer 31236 2 snd_seq,snd_pcm snd 60260 10 snd_intel8x0m,snd_intel8x0, snd_ac97_codec,snd_seq_oss,snd_seq,snd_seq_device,snd_pcm_oss, snd_mixer_oss,snd_pcm,snd_timer soundcore 14304 1 snd snd_page_alloc 14724 3 snd_intel8x0m,snd_intel8x0, snd_pcm 8139too 33152 0 mii 10240 1 8139too ext3 151048 2 jbd 70552 1 ext3 dm_mod 67748 1 ===================================================== o ifconfig -a ===================================================== eth0 Link encap:Ethernet HWaddr 00:40:D0:34:B8:BC inet addr:10.124.50.61 Bcast:10.124.50.255 Mask:255. 255.255.0 inet6 addr: fe80::240:d0ff:fe34:b8bc/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) Interrupt:17 Base address:0xe400 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:14 errors:0 dropped:0 overruns:0 frame:0 TX packets:14 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1148 (1.1 KiB) TX bytes:1148 (1.1 KiB) sit0 Link encap:IPv6-in-IPv4 NOARP MTU:1480 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) veth0 Link encap:Ethernet HWaddr 00:00:00:00:00:00 BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) vif0.0 Link encap:Ethernet HWaddr FE:FF:FF:FF:FF:FF BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) ===================================================== Thanks, AKio _______________________________________________ Xen-users mailing list Xen-users@lists.xensource.com http://lists.xensource.com/xen-users
> I got xen-unstable.hg, did a fresh hg pull today(08/01). > Then I built and installed xen-unstable. > > I can boot up Xen and Dom0. (DomU didn''t create.) But a > network of Dom0 cannot be connected. > How should I do? > > I use RTL-8139 network card, and 8139too. > So, I checked /proc/interrupts and network interrupts didn''t count. > =====================================================> CPU0 > 17: 0 Phys-irq yenta, eth0It might be worth disabling PCMCIA (yenta) and seeing if that helps. There''s been several complaints about shared interrupts not working. Also, compare the boot messages (particularly wrt to interrupt routing) of a Xen/dom0 boot vs an equivalently configured native kernel. Best, Ian _______________________________________________ Xen-users mailing list Xen-users@lists.xensource.com http://lists.xensource.com/xen-users
takebe_akio@jp.fujitsu.com
2005-Aug-03 05:09 UTC
RE: [Xen-users] Network interrupts disable?
Hi, Thank you for the reply. I did a fresh hg pull again(08/02). (and aplied a patch of "vaddr=0".)> >It might be worth disabling PCMCIA (yenta) and seeing if that helps. >There''s been several complaints about shared interrupts not working.Then I tried to be disabling PCMCIA (yenta) and so on. But the network isn''t enable. - lsmod =================================== Module Size Used by video 14212 0 thermal 11016 0 processor 14884 1 thermal fan 3460 0 button 5008 0 battery 7684 0 ac 3460 0 sis_agp 6276 1 agpgart 28872 1 sis_agp 8139too 24576 0 =================================== - cat /proc/interrupts =================================== CPU0 1: 99 Phys-irq i8042 9: 0 Phys-irq acpi 12: 101 Phys-irq i8042 14: 111080 Phys-irq ide0 15: 217 Phys-irq ide1 17: 0 Phys-irq eth0 20: 0 Phys-irq ohci_hcd:usb1 21: 0 Phys-irq ohci_hcd:usb2 22: 0 Phys-irq ohci_hcd:usb3 256: 0 Dynamic-irq ctrl-if 257: 8381 Dynamic-irq timer0 258: 0 Dynamic-irq console 259: 0 Dynamic-irq net-be-dbg NMI: 0 LOC: 0 ERR: 0 MIS: 0 ====================================> >Also, compare the boot messages (particularly wrt to interrupt routing) >of a Xen/dom0 boot vs an equivalently configured native kernel. >So, I checked dmesg as you say. But I did not find a error messages. Is there any other check points? Please tell me how to debug it. ===============================--- orig/orig_dmesg.txt 2005-08-03 02:14:32.000000000 +0900 +++ xen/dmesg.txt 2005-08-03 02:20:31.000000000 +0900 @@ -1,21 +1,13 @@ -Linux version 2.6.12 (root@test-host.soft.fujitsu.com) (gcc バージョン 4.0.0 20050519 (Red Hat 4.0.0-8)) #1 Wed Aug 3 02:04:38 JST 2005 +Linux version 2.6.12-xen0 (root@test-host.soft.fujitsu.com) (gcc バージ ョン 4.0.0 20050519 (Red Hat 4.0.0-8)) #2 Wed Aug 3 01:33:07 JST 2005 BIOS-provided physical RAM map: - BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) - BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) - BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) - BIOS-e820: 0000000000100000 - 000000002dff0000 (usable) - BIOS-e820: 000000002dff0000 - 000000002dff3000 (ACPI NVS) - BIOS-e820: 000000002dff3000 - 000000002e000000 (ACPI data) - BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) - BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) - BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved) + Xen: 0000000000100000 - 0000000010000000 (usable) 0MB HIGHMEM available. -735MB LOWMEM available. -found SMP MP-table at 000f5300 -On node 0 totalpages: 188400 - DMA zone: 4096 pages, LIFO batch:1 - Normal zone: 184304 pages, LIFO batch:31 +256MB LOWMEM available. +On node 0 totalpages: 65536 + DMA zone: 65536 pages, LIFO batch:31 + Normal zone: 0 pages, LIFO batch:1 HighMem zone: 0 pages, LIFO batch:1 +found SMP MP-table at 000f5300 DMI 2.3 present. ACPI: RSDP (v000 FUJ ) @ 0x000f7460 ACPI: RSDT (v001 FUJ SAXO 0x36312e31 AWRD 0x0100000d) @ 0x2dff3000 @@ -25,7 +17,6 @@ ACPI: DSDT (v001 FUJ SAXO 0x312e3136 MSFT 0x0100000d) @ 0x00000000 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) -Processor #0 15:2 APIC version 20 ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 2, version 2, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) @@ -35,39 +26,35 @@ ACPI: IRQ9 used by override. Enabling APIC mode: Flat. Using 1 I/O APICs Using ACPI (MADT) for SMP configuration information -Allocating PCI resources starting at 2e000000 (gap: 2e000000:d0c00000) +IRQ lockup detection disabled +Allocating PCI resources starting at 10000000 (gap: 10000000:f0000000) Built 1 zonelists -Kernel command line: root=/dev/hda2 ro rhgb -mapped APIC to ffffd000 (fee00000) -mapped IOAPIC to ffffc000 (fec00000) +Kernel command line: root=/dev/hda2 ro rhgb selinux=0 Initializing CPU#0 -PID hash table entries: 4096 (order: 12, 65536 bytes) -Detected 2390.508 MHz processor. -Using tsc for high-res timesource +PID hash table entries: 2048 (order: 11, 32768 bytes) +Xen reported: 2390.290 MHz processor. Console: colour VGA+ 80x25 -Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) -Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) -Memory: 741464k/753600k available (2481k kernel code, 11576k reserved, 825k data, 320k init, 0k highmem) +Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) +Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) +vmalloc area: d0800000-f53fe000, maxmem 2d800000 +Memory: 251520k/262144k available (2685k kernel code, 9500k reserved, 889k data, 312k init, 0k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. -Calibrating delay loop... 4718.59 BogoMIPS (lpj=2359296) +Calibrating delay loop... 4771.02 BogoMIPS (lpj=23855104) Mount-cache hash table entries: 512 CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000 CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000 00004400 00000000 00000000 CPU: Trace cache: 12K uops, L1 D cache: 8K CPU: L2 cache: 512K -CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 00004400 00000000 00000000 +CPU: After all inits, caps: bfebd3f1 00000000 00000000 00000080 00004400 00000000 00000000 CPU: Intel(R) Pentium(R) 4 CPU 2.40GHz stepping 07 Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. -Checking ''hlt'' instruction... OK. +Checking ''hlt'' instruction... disabled ENABLING IO-APIC IRQs -..TIMER: vector=0x31 pin1=2 pin2=-1 checking if image is initramfs... it is -Freeing initrd memory: 983k freed +Freeing initrd memory: 2033k freed NET: Registered protocol family 16 -PCI: PCI BIOS revision 2.10 entry at 0xfa860, last bus=3 PCI: Using configuration type 1 -mtrr: v2.0 (20020519) ACPI: Subsystem revision 20050309 ACPI: Interpreter enabled ACPI: Using IOAPIC for interrupt routing @@ -86,13 +73,30 @@ ACPI: PCI Interrupt Link [LNKF] (IRQs 1 2 3 4 5 6 7 9 *10 11 12 14 15) ACPI: PCI Interrupt Link [LNKG] (IRQs 1 2 3 4 5 6 7 9 10 *11 12 14 15) ACPI: PCI Interrupt Link [LNKH] (IRQs 1 2 3 4 5 *6 7 9 10 11 12 14 15) +xen_mem: Initialising balloon driver. +xen_mem: Delaying watcher init until xenstore is available SCSI subsystem initialized usbcore: registered new driver hub PCI: Using ACPI for IRQ routing PCI: If a device doesn''t work, try "pci=routeirq". If it helps, post a report +Grant table initialized + + *************************************************************** + *************************************************************** + ** WARNING: Currently emulating unsupported memory accesses ** + ** in /lib/tls libraries. The emulation is very ** + ** slow. To ensure full performance you should ** + ** execute the following as root: ** + ** mv /lib/tls /lib/tls.disabled ** + ** Offending process: hotplug (pid=82) ** + *************************************************************** + *************************************************************** + +Pausing... 5<6>IA-32 Microcode Update Driver: v1.14-xen <tigran@veritas. com> Simple Boot Flag at 0x35 set to 0x80 -IA-32 Microcode Update Driver: v1.14 <tigran@veritas.com> Initializing Cryptographic API Continuing... + serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 io scheduler noop registered @@ -106,6 +110,11 @@ pcnet32.c:v1.30j 29.04.2005 tsbogend@alpha.franken.de tun: Universal TUN/TAP device driver, 1.6 tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> +Xen virtual console successfully installed as ttyS0 +Event-channel device installed. +Blkif backend is using grant tables. +Initialising Xen netif backend +Blkif frontend is using grant tables. Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx Probing IDE interface ide0... @@ -157,24 +166,24 @@ md: raid1 personality registered as nr 3 md: raid5 personality registered as nr 4 raid5: automatically using best checksumming function: pIII_sse - pIII_sse : 3020.000 MB/sec -raid5: using function: pIII_sse (3020.000 MB/sec) + pIII_sse : 1119.200 MB/sec +raid5: using function: pIII_sse (1119.200 MB/sec) md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27 device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat. com NET: Registered protocol family 2 -IP: routing cache hash table of 8192 buckets, 64Kbytes -TCP established hash table entries: 131072 (order: 8, 1048576 bytes) -TCP bind hash table entries: 65536 (order: 6, 262144 bytes) -TCP: Hash tables configured (established 131072 bind 65536) +input: AT Translated Set 2 keyboard on isa0060/serio0 +IP: routing cache hash table of 2048 buckets, 16Kbytes +TCP established hash table entries: 16384 (order: 5, 131072 bytes) +TCP bind hash table entries: 16384 (order: 4, 65536 bytes) +TCP: Hash tables configured (established 16384 bind 16384) NET: Registered protocol family 1 NET: Registered protocol family 17 -input: AT Translated Set 2 keyboard on isa0060/serio0 -Bridge firewalling registered -Freeing unused kernel memory: 320k freed logips2pp: Detected unknown logitech mouse model 1 +input: PS/2 Logitech Mouse on isa0060/serio1 +Bridge firewalling registered +Freeing unused kernel memory: 312k freed kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. -input: PS/2 Logitech Mouse on isa0060/serio1 8139too Fast Ethernet driver 0.9.27 ACPI: PCI Interrupt 0000:00:0a.0[A] -> GSI 17 (level, low) -> IRQ 17 eth0: RealTek RTL8139 at 0xe400, 00:40:d0:34:b8:bc, IRQ 17 @@ -195,3 +204,27 @@ EXT3-fs: mounted filesystem with ordered data mode. Adding 1052248k swap on /dev/hda3. Priority:-1 extents:1 eth0: link up, 100Mbps, full-duplex, lpa 0x41E1 +NETDEV WATCHDOG: eth0: transmit timed out +eth0: Transmit timeout, status 0c 0005 c07f media 10. +eth0: Tx queue start entry 4 dirty entry 0. +eth0: Tx descriptor 0 is 0008a03c. (queue head) +eth0: Tx descriptor 1 is 0008a03c. +eth0: Tx descriptor 2 is 0008a03c. +eth0: Tx descriptor 3 is 0008a03c. +eth0: link up, 100Mbps, full-duplex, lpa 0x41E1 +NETDEV WATCHDOG: eth0: transmit timed out +eth0: Transmit timeout, status 0c 0005 c07f media 10. +eth0: Tx queue start entry 4 dirty entry 0. +eth0: Tx descriptor 0 is 0008a05b. (queue head) +eth0: Tx descriptor 1 is 0008a05b. +eth0: Tx descriptor 2 is 0008a05b. +eth0: Tx descriptor 3 is 0008a07c. +eth0: link up, 100Mbps, full-duplex, lpa 0x41E1 +NETDEV WATCHDOG: eth0: transmit timed out +eth0: Transmit timeout, status 0c 0005 c07f media 10. +eth0: Tx queue start entry 4 dirty entry 0. +eth0: Tx descriptor 0 is 0008a07c. (queue head) +eth0: Tx descriptor 1 is 0008a07c. +eth0: Tx descriptor 2 is 0008a07c. +eth0: Tx descriptor 3 is 0008a07c. +eth0: link up, 100Mbps, full-duplex, lpa 0x41E1 =============================== xm dmesg is the bellow. =================================================== __ __ _____ ___ _ _ \ \/ /___ _ __ |___ / / _ \ __| | _____ _____| | \ // _ \ ''_ \ |_ \| | | |__ / _` |/ _ \ \ / / _ \ | / \ __/ | | | ___) | |_| |__| (_| | __/\ V / __/ | /_/\_\___|_| |_| |____(_)___/ \__,_|\___| \_/ \___|_| http://www.cl.cam.ac.uk/netos/xen University of Cambridge Computer Laboratory Xen version 3.0-devel (root@soft.fujitsu.com) (gcc バージョン 4.0.0 20050519 (Red Hat 4.0.0-8)) 2005年 8月 3日 水曜日 01:34:24 JST Latest ChangeSet: Wed Aug 3 08:13:50 2005 565cec5b9cc2d861c698f913cb9af3dec4f78726 (XEN) Physical RAM map: (XEN) 0000000000000000 - 000000000009fc00 (usable) (XEN) 000000000009fc00 - 00000000000a0000 (reserved) (XEN) 00000000000f0000 - 0000000000100000 (reserved) (XEN) 0000000000100000 - 000000002dff0000 (usable) (XEN) 000000002dff0000 - 000000002dff3000 (ACPI NVS) (XEN) 000000002dff3000 - 000000002e000000 (ACPI data) (XEN) 00000000fec00000 - 00000000fec01000 (reserved) (XEN) 00000000fee00000 - 00000000fee01000 (reserved) (XEN) 00000000ffff0000 - 0000000100000000 (reserved) (XEN) System RAM: 735MB (753212kB) (XEN) Xen heap: 10MB (10660kB) (XEN) PAE enabled, limit: 16 GB (XEN) found SMP MP-table at 000f5300 (XEN) DMI 2.3 present. (XEN) Using APIC driver default (XEN) ACPI: RSDP (v000 FUJ ) @ 0x000f7460 (XEN) ACPI: RSDT (v001 FUJ SAXO 0x36312e31 AWRD 0x0100000d) @ 0x2dff3000 (XEN) ACPI: FADT (v002 FUJ SAXO 0x36312e31 AWRD 0x0100000d) @ 0x2dff3040 (XEN) ACPI: BOOT (v001 FUJ SAXO 0x36312e31 AWRD 0x0100000d) @ 0x2dff5840 (XEN) ACPI: MADT (v001 FUJ SAXO 0x36312e31 AWRD 0x0100000d) @ 0x2dff5880 (XEN) ACPI: DSDT (v001 FUJ SAXO 0x312e3136 MSFT 0x0100000d) @ 0x00000000 (XEN) ACPI: Local APIC address 0xfee00000 (XEN) ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) (XEN) Processor #0 15:2 APIC version 20 (XEN) ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) (XEN) IOAPIC[0]: apic_id 2, version 2, address 0xfec00000, GSI 0-23 (XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) (XEN) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 dfl dfl) (XEN) ACPI: IRQ0 used by override. (XEN) ACPI: IRQ2 used by override. (XEN) ACPI: IRQ9 used by override. (XEN) Enabling APIC mode: Flat. Using 1 I/O APICs (XEN) Using ACPI (MADT) for SMP configuration information (XEN) Initializing CPU#0 (XEN) Detected 2390.305 MHz processor. (XEN) Using scheduler: Simple EDF Scheduler (sedf) (XEN) CPU: Trace cache: 12K uops, L1 D cache: 8K (XEN) CPU: L2 cache: 512K (XEN) CPU: Hyper-Threading is disabled (XEN) CPU0: Intel(R) Pentium(R) 4 CPU 2.40GHz stepping 07 (XEN) Total of 1 processors activated. (XEN) ENABLING IO-APIC IRQs (XEN) ..TIMER: vector=0x31 pin1=2 pin2=-1 (XEN) Platform timer is 1.193MHz PIT (XEN) Brought up 1 CPUs (XEN) mtrr: v2.0 (20020519) (XEN) *** LOADING DOMAIN 0 *** (XEN) Xen-ELF header found: ''GUEST_OS=linux,GUEST_VER=2.6,XEN_VER=3.0, VIRT_BASE=0xC0000000,PAE=yes,LOADER=generic'' (XEN) PHYSICAL MEMORY ARRANGEMENT: (XEN) Dom0 alloc.: 10000000->20000000 (XEN) VIRTUAL MEMORY ARRANGEMENT: (XEN) Loaded kernel: c0100000->c05133e4 (XEN) Init. ramdisk: c0514000->c0710400 (XEN) Phys-Mach map: c0711000->c0751000 (XEN) Page tables: c0751000->c075a000 (XEN) Start info: c075a000->c075b000 (XEN) Boot stack: c075b000->c075c000 (XEN) TOTAL: c0000000->c0800000 (XEN) ENTRY ADDRESS: c0100000 (XEN) Initrd len 0x1fc400, start at 0xc0514000 (XEN) Scrubbing Free RAM: ........done. (XEN) *** Serial input -> DOM0 (type ''CTRL-a'' three times to switch input to Xen). ================================================== Thanks, Akio _______________________________________________ Xen-users mailing list Xen-users@lists.xensource.com http://lists.xensource.com/xen-users