similar to: XEN - Broadcom issue: survey

Hello, I''ve this strange problem. When Xen kernel start and it try to start eth devices, network doesn''t work. It seems to be a problem with NICs firmware. Anyone had this problem? Do you know where I can download firmware upgrade? (on DELL''s site I''ve just searched...) Thanks, Carlo No virus found in this outgoing message. Checked by AVG Free Edition.

Hi all, I''ve a Xen server (Xen 3.1 compiled from sources [stable downloaded last wed...], CentOS 5 as the host OS, HP Proliant G5 6Gb ram with Broadcom NetXtreme 2) with 4 guests, each running Windows 2003 just installed, with nothing else. Network is configured with the default bridging script, no changes. I''m using 1 network card only for the moment. All guests run apparently

I have a new x3655 IBM and whenever the /etc/xen/scripts/network-bridge script starts, the ethernet would no longer work. This post isn''t about the cause, but the fix. I did a lot of tcpdumps and Googling, but I''ll spare you that. All they do is prove that yes, there is an issue. :) I tried Debian 4.0 i386/amd64 and Ubuntu 7.04 Server i386/amd64 and they all exhibit the

I just kickstarted a new machine with the latest CentOS 6.2 files, including kernel 2.6.32-220.13.1.el6.x86_64. It came up without network interfaces. dmesg says: bnx2: Broadcom NetXtreme II Gigabit Ethernet Driver bnx2 v2.2.1 (Dec 18, 2011) alloc irq_desc for 36 on node -1 alloc kstat_irqs on node -1 bnx2 0000:01:00.0: PCI INT A -> GSI 36 (level, low) -> IRQ 36 bnx2 0000:01:00.0:

I have a broadcom bcm5722 and a dual intel pro/1000 pt nic in a dell t110. The setup sees the cards and i put them into automatic mode. After the install no cards are detected at all. Astaro 8.01 detects and utilizes all of these cards just fine. I have also tried ubuntu server 10.04 lts and they work fine. I'm curious if this is a bug with Centos 6?

Hello list, I have two differents installation Xen Hypervisor on two identical physical server, on the same switch : The problem is on my new server (Xen 4.0.1 with pvops kernel 2.6.32.24), I have bad performance on bandwidth I have test with a files copy and "iperf". Result iperf average: Transfert Bandwidth XEN-A -> Windows

Hi all, I have a problem when from domU I need to configure a network interface. My system configuration is the next: dom0: xen 3.4.3 with 2.6.18-238.9.1.el5xen kernel, making pci back from a network card. All ok. This is the result from "lspci -v -s 09:00.0" 09:00.0 Ethernet controller: Broadcom Corporation NetXtreme II BCM5708 Gigabit Ethernet (rev 12) Subsystem: Broadcom

Hi, I''ve run into the same issue as: http://lists.xensource.com/archives/html/xen-users/2006-07/msg00599.html In that, running the network bridge script kills networking completely, trying to ping the gateway gives me destination host unreachable. The card is: 09:00.0 Ethernet controller: Broadcom Corporation NetXtreme II BCM5708 Gigabit Ethernet (rev 11) Using the bnx2 module:

Hi all I'm trying to setup second ethernet on Dell 2950 server but there isn't any eth1 device (in the bios are ON) # dmesg |grep eth eth0: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X 64-bit 133MHz found at mem f8000000, IRQ 169, node addr 001c23d878bb eth1: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X 64-bit 133MHz found at mem f4000000, IRQ 169, node addr 001c23d878bd

Hi Well we are now using HP instead of Dell and have hit a major hurdle. We dont seem to be able to kix any of these boxes. I have been most recently trying on a dl585 and the issue appears to be that the kix kernel does not detect any nic. Its strange as the box can be installed using iso's and the nic appears as eth0: Broadcom NetXtreme II BCM5706 1000Base-T (A2) PCI-X 64-bit 100MHz

I am having the same problem. But, I cannot access to the following link for solution http://wiki.ncsa.uiuc.edu/wiki/Dell_PE1950_NIC_Firmware_Workaround Can someone send me the content of this link? Thanks. Pete, This may be relevant: http://wiki.ncsa.uiuc.edu/wiki/Dell_PE1950_NIC_Firmware_Workaround - Mike At 8/18/2006 09:40 AM Friday, Peter McEvoy wrote: Hi, I''ve run

hallo everybody, i googled a lot of time, looking for PV-drivers for Windows- domUs. I found a few things about that, but nothing about download an installation. Do anybody know, where I can get it and how to install? My configuration: Dom0: CentOS 5.1 DomUs: Windows XP and 2003 Server Thanks for any help, Guenter _______________________________________________ Xen-users mailing list

I am having an extremely strange issue with a BL460c1 (G1) blade on a c7000 enclosure. I could not for the life of me get the machine to ping the gateway or any other blade on the same enclosure (yes, the subnet mask was correct & quadruple-checked); although pinging to the local IP works. I was almost convinced that it was a network or hardware issue; until I asked someone to try

I installed 64-bit xen 3.1.0 (from xensource.com tarballs) on three new machines today, using a configuration setup that I''ve used successfully many times before. However, I encountered a new problem. These are Dell Poweredge 1950 servers, by the way. >From lspci 04:00.0 Ethernet controller: Broadcom Corporation NetXtreme II BCM5708 Gigabit Ethernet (rev 12) 08:00.0 Ethernet

??Hi all! We use Samba 3 server for some video stuff (editing, rendering, and so on) -- that's why performance is critical. We've tried a lot smb.conf options, but Samba can't satisfy our requirements. Our server configuration is as following: * Hard drive: RAID5 (8 x Seagate 7200.10), 3ware 9550SX-8LP controller * NICs (trunked): 2 x Broadcom NetXtreme BCM5704 * Processor: Opteron

Hey all I''m new to Linux and Virtualizing. I''m trying to dedicate my nic''s to each virtual server. For instance, virt server A would use nic1 and virt server B would use nic2 and so on. I''ve been reading some stuff for this list and to tell you the truth I''m a bit overwhelmed. We are going to run SLES10.1 and Xen. I would appreciate any assistance.

Hi, We have a HP DL385 G6 server that is having an issue. Two of the 4 network cards are not being recognised by Linux. We have quite a few other servers with the same hardware and no issues but, before I call HP, I would like to make sure that I am not doing anything wrong :) I have tried with the kernel that came with CentOS 5.5 and the updated one kernel-2.6.18-194.11.3. I do an lspci

Package: xen-hypervisor-3.4-amd64 and linux-image-2.6.32-5-xen-amd64 Version: 3.4.3-1 and 2.6.32-15 Hello all, GRUB-PC does not automatically populate Xen related parameters in /boot/grub/grub.cfg so I added them manually (see below). All the packages involved on my Dell PowerEdge R710 running Debian GNU/Linux Squeeze AMD64 are from the Squeeze repository. There are four (4) 1TB SATA HDD

Hi Michael: Sorry to brother. But I''ve been suffered this issue quite a long time. My test environment is 2.6.32.36 + xen 4.0.1 + bnx2, 2.3. Also cpu idle is disabled in grub. Grub info: title Red Hat Enterprise Linux Server (2.6.32.36xen) kernel /xen-4.0.1.gz iommu=off x2apic=off console=com1,vga com1=115200,8n1 noreboot cpuidle=0 cpufreq=none

Hi, I need to fit at least three NICs and I was looking for motherboard models that contain 3 or 4 CPI (or PCI-e) slots and works with CentOS. I had a problem in the past with some models that had a bug and did not work well with linux (ok with windows) so that's way I am asking this here. -------------- next part -------------- An HTML attachment was scrubbed... URL: