similar to: Device recommendation Salicru

On 8/19/20 12:55 PM, Marc Franquesa wrote: > Thanks all for the quick responses on the question (always a good sign > of this mailing list). > > (Tim Dawson, Manuel Wolfshant): > Regarding root cause of my current problem pointing to a faulty > battery, this is not the first time that someone points to it. However > I made a simple test with the vendor tools (Windows) and

Thanks all for the quick responses on the question (always a good sign of this mailing list). (Tim Dawson, Manuel Wolfshant): Regarding root cause of my current problem pointing to a faulty battery, this is not the first time that someone points to it. However I made a simple test with the vendor tools (Windows) and didn't found any issue, as well as they discharged normally (although only

Hello, I have a Salicru SPS One 700VA device, I want to manage it with Debian Whezzy. I read some information in the net about how to configure but I can not get it working. Could you help with this? This is the log when I connect the USB: [ 3194.688204] usb 4-4: new low-speed USB device number 2 using ohci_hcd [ 3194.857239] usb 4-4: New USB device found, idVendor=0665, idProduct=5161 [

My experience on situations like this is that it is almost always a bad battery.  Once load is removed, the voltage bounced back, and thus you show time/capacity, but it's possible that the sag under load drops you into LB, and causes the shutdown. If the UPS has a battery test, give it a try, or load test the battery external to the UPS if you can - I suspect that the UPS will be fine,

On Nov 8, 2013, at 3:23 AM, Josu Lazkano wrote: > Hello, I have a Salicru SPS One 700VA device, I want to manage it with > Debian Whezzy. > > I read some information in the net about how to configure but I can > not get it working. I'm assuming you mean this blog post? http://blog.ciberterminal.net/2013/04/28/ups-salicru-en-nut/ > Could you help with this? > >

Hi, my name is Sebasti?n from Spain I need help for that. I have 2 salicru ups I need monitor with a fedora 14 pc. Someone knows if i can configure ups.conf to monitor one or another ups? only make a upsc "ups" for take data. The upses are connected via usb and nut always read the first one connected. The upses are the same model. Thanks for all! Sebasti?n Le?n del Moral urticaries at

I would also be very interested in this topic. Best Regards, Bart pon., 17 sie 2020, 12:55 użytkownik Marc Franquesa <marc.franquesa at gmail.com> napisał: > Sorry, because this is not a technical question rather than a Hardware > advice/recommendation. > > I have been using NUT-UPS perfectly for more than 7 years using two > different Eaton/MGE models. > > After a

The REDi Blazer 600VA (BLAZER600c) UPS found here [ro_RO]: http://www.emag.ro/ups-redi-blazer-600va-blazer600c/pd/EX5X2BBBM/ which is actually a Centralion Blazer 600VA [en_TW]: http://www.centralion.com/html/product/back-Product-ups-blazer400.htm works with the blazer_ser driver ----------shell output---------- # upsrw ups # upscmd -l ups Instant commands supported on UPS [ups]: beeper.toggle -

Le samedi 12 septembre 2009 ? 01:59 -0300, Vitor Choi Feitosa a ?crit : > Hi Arnaud, Hi Vitor, > I found your email on the contact page and since you seem to work for > Eaton and is involved in the NUT community I think you're the right > person to contact. > > I've got an Eaton NV 1000H and just installed it here. Before NUT > configuration I've checked the HCL

Hi Sergey, 2011/7/15 Sergey Talchuk <tals1975 at gmail.com> > Hi Arnaud, > > both configurations are ok :). Please find the file attached. > logic since the 2nd is automatically guessed from the first using USB Vendor and Product ID ;-) can you please send in upsc, upscmd and upsrw output. and also report the shutdown testing as described here:

Not of a big help here, but I think it's a voltronic power vesta 650: http://www.voltronicpower.com/oCart2/index.php?route=product/product&path=37&product_id=52 If that is the case, it should work both with the blazer drivers (i.e. all but the shutdown sequence) and with the now defunct voltronic ones. With arno's words: "We are currently merging a new driver to replace

I'm running NUT 2.6.3 on Debian wheezy [ with a 3.3.0 i686 kernel ] I've installed NUT via Debian APT [ package nut version 2.6.3-1 ] I have a REDi Blazer 600VA (BLAZER600c) UPS and I want to detect power failures. I have tried the following drivers: * gamatronic: Can't talk to UPS on port /dev/ttyS1! * bestups: Unable to detect a Best/SOLA or Phoenix protocol UPS * blazer_ser: No

Hi, recently I observed that during a power outage, my NUT setup doesn't shutdown properly. Indeed it never reaches the LowBattery state to notify and initiate shutdown on clients. Reviewing my setup and logs I think I'm facing multiple problems and I'm unable to point to real root cause. First, let me focus on my scenario and current setup: In normal status (ONLINE, fully charged)

Hi Mutlu, 2009/8/7 Mutlu T. <cmtunc at gmail.com> > Redirecting to debian.org domain due to being rejected as spam by free.fr > > > ------- Forwarded message ------- > From: "Mutlu T." <cmtunc at gmail.com> > To: arnaud.quette at free.fr > Cc: > Subject: New NUT HCL entry / (brand)Inform (series)Informer Compact > Date: Fri, 07 Aug 2009 15:31:04

This UPS is already listed in the compatibility list. But I wanted to add the instant commands supported by upscmd: ============================ Instant commands supported on UPS [PW5125]: beeper.disable - Disable the UPS beeper beeper.enable - Enable the UPS beeper beeper.mute - Temporarily mute the UPS beeper load.on - Turn on the load immediately outlet.1.load.off - Turn off the load on

Hi!. I recently installed NUT on my servers to monitor a Eaton Ellipse UPS. Now I'm planning my next step: Monitor the UPS status with cacti using snmp. I see that there was a nut snmp subagent (I'm not talking about the nut-snmp driver) (http://www.networkupstools.org/server-projects/). But the current link doesn't work (404). I haven't found anything about it in the web. ?Is

Hello all, I have a Salicru UPS (Salicru SPS One 700VA) working great in Debian Wheezy, but I want to move it to a OpenWRT router. I configured same as in Debian but I can not get it working: # upsd Network UPS Tools upsd 2.6.5 fopen /var/run/upsd.pid: No such file or directory listening on 192.168.1.240 port 3493 /etc/nut/ is world readable Can't connect to UPS [salicru]

Hello, just joined to the list, because i have a problem. :S We have 2 exact same configuration: basic Fujitsu server + Eaton NV1000H ups. OS is Debian Squeeze. According to the driver list, the ups uses the blazer_usb driver. I never tried nut before, so i read some of the docs, and configured it manually. The problem pops up when i try to simulate the power-outage. I just unplug the ups'

On Aug 19, 2020, at 6:22 AM, Manuel Wolfshant wrote: > > On 8/19/20 12:55 PM, Marc Franquesa wrote: >> Thanks all for the quick responses on the question (always a good sign of this mailing list). >> >> (Tim Dawson, Manuel Wolfshant): >> Regarding root cause of my current problem pointing to a faulty battery, this is not the first time that someone points to it.

Device Manufacturer: Eaton Device Name: 5S1500LCD ---------------------------------------------------------- upsc output: battery.charge: 100 battery.charge.low: 20 battery.runtime: 3515 battery.type: PbAc device.mfr: EATON device.model: Ellipse PRO 1500 device.serial: 0000000000 device.type: ups driver.name: usbhid-ups driver.parameter.pollfreq: 30 driver.parameter.pollinterval: 2