similar to: FW: POWERCOM HID USB controller update

Dear Sirs, We appreciate your support and cooperation. Can you please kindly add our new USB-controller with productID 0X04 to NUT compatible list. Updated USB-controller compatible with previous version which is supported by your usbhid-ups driver. Detailed information regarding new POWERCOM communication protocol you could download via link

On Sep 11, 2014, at 2:50 AM, Khokhlov Artem <khokhlov.a at pcm.ru> wrote: > Can you please kindly add our new USB-controller with productID 0X04 to NUT compatible list. Updated USB-controller compatible with previous version which is supported by your usbhid-ups driver. Confused. This commit was added in 2011:

Hello. Not listed as supported, so here is some info, [root at vhost ~]# /usr/sbin/usbhid-ups -DD -a powercom Network UPS Tools - Generic HID driver 0.38 (2.7.2) USB communication driver 0.32 0.000000 debug level is '2' 0.001318 upsdrv_initups... 0.074753 Checking device (0529/0001) (003/002) 0.074835 Failed to open device, skipping. (Permission denied)

Dear Sirs, First of all I would like to thank you for support PCM product in your project. Kindly please be informed that POWERCOM launch new USB-controller with productID 0X04. Updated USB-controller compatible with previous version which supported by your usbhid-ups driver. There is added some command and changed idProduct. Vendor ID stay the same 0X0d9f without changes. Detailed information

Hello. It's been a while since I started this topic. I've finally tested it on Linux desktop PC. Nut version 2.6.4-2.3 Basically the behavior is the same as on raspberry pi. It reports "battery needs to be replaced" regularly and I got "on battery" message 114107.780504 Path: UPS.PowerSummary.PresentStatus.ACPresent, Type: Input, ReportID: 0x0a, Offset: 2, Size: 1,

[I am CC'ing Alexey from Powercom in case he has seen any of these issues with the Raspberry Pi hardware.] On Jun 10, 2013, at 1:05 PM, M?rti?? Pu??tis wrote: > I took the log. Here's what happened. > Broadcast Message from nut at rasp > (somewhere) at 16:18 ... > UPS BNT500AP at localhost battery needs to be replaced > > occurred when for the first time value

I took the log. Here's what happened. Broadcast Message from nut at rasp (somewhere) at 16:18 ... UPS BNT500AP at localhost battery needs to be replaced occurred when for the first time value "1" was read as "UPS.PowerSummary.PresentStatus.NeedReplacement", on this line: 6409.240690 Path: UPS.PowerSummary.PresentStatus.NeedReplacement, Type: Input, ReportID: 0x0a,

Gentlemen, I have a new HID USB device, that seems to be quite similar to the currently supported APC HID UPS. I append the dump-tree output, and would much appreciate advice on how to proceed. Certain entries for the current device are not available, but maybe there are some replacements that could be used. This may of course require a new table in apc-hid.h, and I would prefer not to do this

Hi! Info OS: TinyCore Linux 4.5.6 NUT version: 2.6.4 NUT innstallation method: source tarball Device name: Eaton Ellipse ups eco 1600 usb din (EL1600USBDIN) /usr/local/ups/etc/ups.conf file: [eaton] driver = usbhid-ups port = auto When I run: root at Dalen:/usr/local/ups/bin/upsdrvctl start eaton I get this error message: Network UPS Tools - UPS driver controller 2.6.4

To all, I attempted to configure the UPS tools for the Tripp-Lite SmartOnline 1500VA 2U rackmount UPS. I followed the instructions from the 'upsdrvctl start' output and posted the diagnostic information below. Is my UPS using an unknown product ID as reported? From the mailing list archive, I have found another posting for the same UPS with device model '09AE/4003', whereas

Hello, I am hoping someone can point me in the right direction. I am setting up a new UPS, most things seem to be working except the UPS turns off immediately during a test shutdown using///"//upsmon -c fsd".//No delay before the UPS turns itself off leaving no time for the server to shutdown properly. I have attempted to set the delay higher using "upsrw -s

When running 'sudo upsmon -c fsd' UPS turns off then back on after a delay as expected. But when power is disconnected and the command is ran, the UPS turns off but still turns back on again. Changing 'ondelay' to -1 or 0 does not change the behavior. How can I get the UPS load to stay turned off if there is no power? Or am I misunderstanding how to test this functionality?

Hi, I'm trying to generate a skeleton driver with usbhid-ups and gen-usbhid-subdriver but the output seems to be incorrect. Same behavior with stable 2.6.5, so I guess there is something wrong with data coming out of device. I attached the output of usbhid-ups and gen-usbhid-subdriver from the commands: drivers/usbhid-ups -DD -u root -x explore -x vendorid=04d8 -a openups >&

My UPS is connected to a Raspberry Pi by USB. After a few hours of working, the service fails. Looking at kernel messages I noticed that the device is repeatedly disconnecting and reconnecting. I have tried using a different USB port and using a brand new USB cable. I have not had success by changing config parameters like pollfreq/pollinterval/etc. What is causing the UPS to keep disconnecting?

Hello all, About a month ago Peter and Charles were kind enough to try to help me with getting a Tripp Lite USB UPS to work with NUT. I reported quite a bit of initial success, and then other things here fell apart. Between work, fence building and a week-long out of town business trip, I have had to drop this from my list of things to do lately. I am back at it, and I believe I will have

I have a Tripp-Lite BCPERS450, connected to a system running Ubuntu 16.04.3 LTS and NUT 2.7.2-4ubuntu1.2. I had to make my own /lib/systemd/system-shutdown/nutshutdown, but now everything is working except for powering on and off the UPS. Regardless of the settings of offdelay and ondelay in upsconf, and regardless of whether the AC power is on, when I say "upsdrvctl shutdown" the UPS

Thanks for your help. From: Charles Lepple <clepple at gmail.com> Date: Mon, 18 Dec 2017 19:26:56 -0500 This may sound like an apples-to-oranges comparison, but we did uncover an issue with CyberPower UPSes where the delay values needed to be greater than or equal to 60 (seconds), since they were being rounded down to integer numbers of minutes internally: What was the largest

Hi, I have a HP R1500 G2 UPS and want to get it working under Debian Lenny - as this OS is not supported by HP I'm trying to use nut for it - but I can't get it working. Do I have any chance to get the UPS running with nut. I also tried different drivers but had no luck either. Or does anyone has experience with HP UPS under debian ? Any help would be nice ! I tried /lib/nut/usbhid-ups

Hi there, OS: (L)ubuntu 12.04 precise LTS Nut: 2.6.3-1ubuntu1.1 Installation Method: Package (apt-get install nut) Hardware: HP R1500 G3 INT Hardware-Specs: http://h18004.www1.hp.com/products/quickspecs/14059_div/14059_div.pdf Problem: I tried to set up nut with our new arrived HP R1500 G3 UPS but there is a failure with the usb connection. After trying "/lib/nut/usbhid-ups -DD -a

Hi - I just installed NUT from source, using the usbhid-ups driver for a tripplite UPS (i compiled with the appropriate flag for the USB device). NUT version is 2.7.3. I UPS is AVR900U System is archlinux - fully up to date, running on an ARM device. Linux <Systemnameomitted > 3.1.10-35-ARCH #1 PREEMPT Fri Jan 23 19:14:18 MST 2015 armv5tel GNU/Linux I can communicate with my UPS - no