similar to: blazer driver: Possible bugs with battery packs

Hello all, been 5 years since I posted on this list, glad to be back :) I have a number of X-power Tigra 1kVA online UPS units. From some knowledgeable folks working for the local distributor, I learnt that from inside this looked like a Best 610 ups unit. Before, I had this UPS hooked via serial to my Windows 2003 server. For monitoring, some winpilot/upspilot software was also provided.

Dear Ladies and Gentlemen, I have several old, yet functioning APC Smart-UPS (Model 600LS, Part AP600I, Firmware 6JI, no EEPROM, from 1991). They are not supported by Powerchute any more. I run NUT 2.6.5-4 on Windows XP SP3. I use COM1 port with cable 940-0024C. The connection fails with APC Smart protocol driver 3.0 (2.6.3-3534:3540M), APC command table version 3.0 or higher - it works with APC

Hi, I have a bunch of UPSs, most connected to pcs with Linux working 100% with NUT. The only one I have a problem with, is connected to Windows 7 64bit, and I used the straight MSI installed from the website named NUT-Installer-2.6.5-4.msi Took me a while to find a way to get it to work, but it is ugly for now. Just starting up the service results in a NUT not working at all, and I tracked it

Hello, I have just installed nut_2.6.0 from Debian testing, do anyone know the correct driver for this ups? The blazer_usb don't report battery-charge, the bundled software report charge and runtime. root at pluto<~>upsc powerwalker battery.voltage: 40.86 battery.voltage.nominal: 36.0 beeper.status: enabled device.mfr: device.model: HV 1K device.type: ups driver.name: blazer_usb

hi! When I turn on my pc everything works fine, but if I restart fails (I'm not sure if this is true at 100%)?(then, i can do 'sudo /etc/init.d/nut restart' and it works) But what is certain is that sometimes when start up the pc it works and sometimes fails, can be a problem with the start time (i have a fast ssd) and the initialization of the driver and the usb port? thanks! syslog:

I'm running Ubuntu 14.04.1 with nut 2.7.1-1ubuntu1, using a Powerwalker/INNO TECH ups. It used to working fine, but lately blazer_usb just executes a few commands and then terminates with a "Got disconnected by another driver" message. Any suggestions? Example output from blazer_usb with loads of debug: # /lib/nut/blazer_usb -DDDDDDDDDDDDDDDDDDDDDD -a nasups Network UPS Tools -

@fsp Please forward to development, manufacturing and quality management department: Model EP1000(PPF6000/100), 431107300095, 4711140480534, Art-Nr. 8296861, 70539, 14Z00000, 35-0200116-01G @nut-users http://www.networkupstools.org/ 2.4.3 debian stable, 2.6.2 upstream, linux 2.6.38-debian-bpo # /usr/local/src/nut-2.6.2/drivers/blazer_usb -u root -DDDDD -a ups Network UPS Tools - Megatec/Q1

BTW, I did a run with a higher debug level that resulted with this... > [root at cornelius ups]# powerpanel -a office -D -D -D -D -D -D -D -D > Network UPS Tools - CyberPower text/binary protocol UPS driver 0.25 (2.6.5) > Warning: This is an experimental driver. > Some features may not function correctly. > > 0.000000 debug level is '8' > 0.011347

Hello First things first, thanks for great work with NUT. For years I used Informer compact 3kVA UPS http://www.informups.com/informer_compact.html with nut/megatec serial driver, but it stopped working when I switched to blazer_ser with 2.6.0 upgrade. I'm using 2.6.0 on gentoo. Blazer_ser seems to connect with UPS, but upsmon reports driver not connected. uname -a Linux localhost

Hi Arnaud and NUT team You may recall some time ago, I and a few others posted questions about the above referenced (cheap and cheerful) USB-based UPS - specifically regarding FreeBSD USB support in NUT. The original posting was entitled "Zigor Ebro 650 compatibility". I've since tried the latest Windows port of NUT with my WinXP laptop connected to the Zigor Ebro and finally

Hello, I have a UPS branded as "Energit MXE II" that comes with the infamous Winpower software (as already discussed in this old thread <http://nut-upsdev.alioth.debian.narkive.com/m0FWk43o/blazer-usb-compatibility-with-ippon-backpro-upses-phoenix-power-co-ltd-usb-to-serial-controller>). This same UPS appears to be sold as "Centralion Titan Elite" and maybe other names

> > hmm, apparently the UPS doesn't close the replies to our queries with > the expected CR and we (I) did not consider that case in nutdrv_qx -- > noted: > https://github.com/networkupstools/nut/issues/441 > > But blazer_usb, being less strict on the terminating CR of Q1 replies, > should work with your device. > > > root at artu:~# upsc Elit at artu > >

Hello! I'm trying to use nut with a Ippon Smart Winner 3000 UPS (http://shop.key.ru/photo/items/45535.jpg) which looks like a custom-labeled OEM model of the megatec branch. I tried both the megatec_usb and the blazer_usb drivers for it, with a obvious config section: [ippon] driver = blazer_usb port = auto vendorid = 06da productid = 0003 desc = "Ippon Smart Winner 3000" If I

It seems like it works (partially?) with NUT/driver you mentioned. I will test it more when I return home. root at Failure:/lib/nut# ./nutdrv_qx -a test -x subdriver=fuji -u root -x productid=0000 -x vendorid=0001 -DDDDDD Network UPS Tools - Generic Q* USB/Serial driver 0.13 (2.7.2.5) USB communication driver 0.32 0.000000 debug level is '6' 0.001247 upsdrv_initups...

Hi, I know it's been a topic many times here, but I've searched the archives, googled for days, and I simply don't believe, that there is still no solution to this. I'm using a PowerCom BNT-600AP ups with usb port. I've downloaded the latest version from svn, compiled it, and tried to use it: * megatec(_usb) - no luck, it did not find the UPS (I?ve read in this list, that

Hey all, Finally got around to hooking up my Powercom BNT-1500AP to nut. It's the old serial interface. Connects okay and gets most information, but a couple of data are way off. Any config recommendations or upgrade recommended? I've played with config a little, but no hits yet. Details: NUT version 2.4.3 ups.conf: [ups] driver = powercom port = /dev/ttyS0

Hi! Normally nut was just worked and worked for me! Not this time though! Distro is Gentoo withe latest nut-2.6.0 emerged today. Linux kernel version is 2.6.36 UPS is PowerCom BNT2000AT "Driver" is powercom ups.conf looks like this! Okay so APC1 is not and APC! [APC1] driver = powercom type = BNT port = /dev/ttyS1 numOfBytesFromUPS = 16

Hi, I have used the truss command as directed. I have attached both the driver output and the last few sections of truss output leading to the hang. Both outputs end at the CTRL+C i pressed when i was forced to end the processes. Hope this is helpful. Please bear with me if i didn't run it with the right options etc - as I mentioned, I'm a little new to Solaris. Regards, Richard On

Hi! Normally nut was just worked and worked for me! Not this time though! Distro is Gentoo withe latest nut-2.6.0 emerged today. Linux kernel version is 2.6.36 UPS is PowerCom BNT2000AT "Driver" is powercom ups.conf looks like this! Okay so APC1 is not and APC! [APC1] driver = powercom type = BNT port = /dev/ttyS1 numOfBytesFromUPS = 16

List: I have an Eaton (Powerware) Model 5115 and am using the bcmxcp_usb driver on a OpenBSD 4.9 system. The upsdrvctl start appears to work and I get a message in my daemon log stating that it successfully started. I can successfully start the upsd daemon. I get a successful start messaage from the upsmon program, but it soon complains of 'stale' data. It looks like the driver