similar to: For APC Back UPS ES users

Hello! I have tested APC Back UPS ES 700 and NUT 2.6.5-3 a few days ago and I have got some news. This device is detected by nut-scanner as: [nutdev1] driver = "usbhid-ups" port = "auto" vendorid = "051D" productid = "0002" product = "Back-UPS ES 700 FW:829.D2 .I USB FW:D2 " serial =

Hello! I try use NUT on some servers. When i use this package on x64 Windows 2003 servers, upsmon hangs on with error: Faulting application upsmon.exe, version 0.0.0.0, faulting module upsmon.exe, version 0.0.0.0, fault address 0x0000458f. I try use another server, on 32-bit all is ok. Problem only on x64 platform (maybe in libusb)? And no different - upsmon master or slave. C:\Program Files

Hi all ! I have a little problem using NUT from FreeNAS. Operating system FreeBSD 8.3-RELEASE-p4 (FreeNAS 8.3.0 BETA 2) UPS American Power Conversion/Back-UPS CS 650 FW:817.v7 .I USB FW:v7 NUT Driver Network UPS Tools - Generic HID driver 0.37 (2.6.5) USB communication driver 0.31 Trying to configure the UPS from FreeNAS failed so I try to investigate which is the problem. Running

?Hello, There is a new intermediate Windows binaries release available at : http://www.networkupstools.org/package/windows/NUT-Installer-2.6.5-3.msi This fixes a regression about stopping the NUT service. Feedback is highly appreciated. Regards, Fred -- Eaton Opensource Team - http://opensource.eaton.com ----------------------------- -----------------------------

?Hello, There is a new intermediate Windows binaries release available at : http://www.networkupstools.org/package/windows/NUT-Installer-2.6.5-2.msi This fixes three regressions: - upssched was not working - Event logging was not working (unless for NUT service binary itself) - usbhid-ups was not working with Back-UPS ES ups. Feedback is highly appreciated. Regards, Fred -- Eaton

Hello! I tried NUT 2.6.5-1 (Windows port) with my APC Back UPS ES. It seems I have configured NUT properly, nut-scanner found my UPS: [nutdev1] driver = "usbhid-ups" port = "auto" vendorid = "051D" productid = "0002" product = "Back-UPS ES 525 FW:851.t3.I USB FW:t3" serial = "8B0745R23575

I was wondering what you guys do about UPS shutdown on Windows systems? Apcupsd has the same issue, so I'm assuming it is the same with NUT. Windows just makes it hard/impossible to do. Do you find draining the batteries down so much cause issues for longevity? Regarding my Eaton 5110, I found that automatic driver setup works just fine on Windows XP but not at all on Windows 7 x64 (I

Hello NUT Team! I am testing the early shutdowns in NUT 2.6.5-1 package for Windows (Windows 7 x64). My configuration files: upsmon.conf RUN_AS_USER upsmon MONITOR upsa at 192.168.10.200 1 upsmon pass master MINSUPPLIES 1 SHUTDOWNCMD "/sbin/shutdown -h +0" NOTIFYCMD "upssched.exe" POLLFREQ 5 POLLFREQALERT 5 HOSTSYNC 15 DEADTIME 15 POWERDOWNFLAG

Windows 7 Pro x64 Eaton 3S550 (brand new, battery mfg 8/15/2012) NUT 2.6.5-3 ups.status: OL CHRG CHRG was present even though it has been plugged in a few days turned on and battery.charge was 100%. Log includes me running upsc and removing power long enough to see that battery.charge will decrease. This UPS doesn't have controlled outlets despite what the upsc output says. ---

hi list, im running debian/testing(act. squeeze) with 2.6.26-2-amd64 kernel. first tried apcupsd what flawlessly worked but because i run nagios (needs nut running for 'check_ups'), im trying to run nut. dmesg and syslog show the device: Jul 27 00:08:06 kate kernel: [16001.477941] hiddev96hidraw0: USB HID v1.10 Device [APC Back-UPS ES 700 FW:829.D3 .I USB FW:D3 ] on usb-0000:00:1d.1-1

I'm trying to use a Nas4Free storage system. This same hardware worked fine on Freenas 0.7.2. O/S: Nas4Free 9.0.0.1.148 which comes with nut 2.6.4. UPS is an APC Back UPS RS 800. USB interface. Driver : usbhid-ups Port: auto my NAS is communicating with the UPS, but in testing power failures, I'm not getting the shutdown to be handled properly. When I pull the AC plug on the UPS,

2011/6/27 Frederic BOHE <fbohe-guest at alioth.debian.org> > Author: fbohe-guest > Date: Mon Jun 27 13:56:51 2011 > New Revision: 3060 > URL: http://trac.networkupstools.org/projects/nut/changeset/3060 > > Log: > Add NUT server scan. > > (...) > device_t * scan_snmp(char * start_ip, char * stop_ip,long usec_timeout, > snmp_security_t * sec); > >

Hi all, I am completely new to NUT and setting up a UPS shut down in Linux. I am looking at buying a APC Smart-UPS X 3000. When I look this device up in the compatibility list this specific model is not listed, only a generic entry for "Smart-UPS". It says to use the *apcsmart* driver. The legend shows this as "protocol based on reverse engineering". What does this

Just my experiences speaking, look at another brand. I use MGE/Eaton and have had much better life and the quality has been much better. APC does not release the protocol for comunicating with the UPS and so to get NUT to work you have to sniff the traffic and then figure out what the commands and responses mean.(thus reverse engineered) APC also will change the protocol between models. (Thus why

Hello NUT Team! I continue playing with NUT for Windows and USBHID-UPS driver I've got from Frederic to fix "Data Stale" problem. It seems there is something wrong when Network UPS Tools service is starting with disconnected USB cable. UPSMON is writing "Data Stale" to output and continue do it infinitely, even the cable is connected back. Here is a short log: Network

Hello, I am trying to get nut running on a Windows 2012 R2 server (x64). I am using the MSI release of 2.6.5-3. The attached UPS is an APC xs1500 (model bx1500g). The connection is an RJ45 to USB cable. Here is my ups.conf: [xs1500] driver = usbhid-ups port = auto desc = "APC Back-UPS xs1500" The problem I am encountering is upsd crashing with an 'Out of memory' error. I can

Hi, I'm running an old APC Smart UPS 900i. As there isn't any software from APC which supports this UPS anymore, I've installed NUT (Gentoo Ebuilds), but version 2.0.5 and version 2.2.2 loose connection to the UPS while version 2.4.1 and SVN version don't show any settings and there are no instant commands. The only information I can get are: driver.name: apcsmart

Hello all, There is a new Windows package of NUT. It now contains nut-scanner binary. Note that there is a known issue with libupsclient.dll with nut-scanner. The scan of NUT servers using nut-scanner will not work for now. You can find it at : http://www.networkupstools.org/source/2.6/NUT-Installer-2.6.3-1.msi Please send feedback to the list. Regards, Fred -- Team Open Source Eaton -

Hi all, I use an APC Back-UPS RS 800, overall my experience with NUT is very good but there is one feature I am missing: the ability to ask the UPS for a battery test. upscmd -l shows the following commands available: $ upscmd -l rs800 Instant commands supported on UPS [rs800]: beeper.disable - Disable the UPS beeper beeper.enable - Enable the UPS beeper beeper.mute - Temporarily mute the UPS

We recently had to replace an old APC SmartUPS 3000 with a newer 3000VA (the 2U one). It has both serial and USB in the back (with an RJ-45 on the end of the serial cable). I can't get the apcsmart driver to connect. I figured it should work the exact same as the old UPS, with /dev/ttyS0 as the port (I'm using the same port on the server that the last one was plugged into). I even