similar to: Zigor Ebro 650 compatibility

Hi all, After some research I've found that this device should run with the blazer_usb driver. Jun 3 16:15:38 pegasus kernel: ugen0.4: <vendor 0x0001> at usbus0 Jun 3 16:15:38 pegasus kernel: uhid0: <vendor 0x0001 product 0x0000, class 0/0, rev 1.00/1.00, addr 4> on usbus0 However, even after shoehorning it; [crees at pegasus]/usr/local/libexec/nut% sudo ./blazer_usb -a zigor

Hi Arnaud and NUT team You may recall some time ago, I and a few others posted questions about the above referenced (cheap and cheerful) USB-based UPS - specifically regarding FreeBSD USB support in NUT. The original posting was entitled "Zigor Ebro 650 compatibility". I've since tried the latest Windows port of NUT with my WinXP laptop connected to the Zigor Ebro and finally

Merry Christmas to you all and best wishes! I ran into exactly the same problem as described. OS: FreeBSD 9.0-Rel UPS: Eaton E-Series NV 600H NUT: from Ports, nut-2.6.5_1 driver: blazer_usb I am sure the problem is not permission-related as it occurs even when the driver runs as root. My tested recipe for USB permissions is: 1. run usbconfig to find where the device is connected. In my case:

Hello! I'm trying to use nut with a Ippon Smart Winner 3000 UPS (http://shop.key.ru/photo/items/45535.jpg) which looks like a custom-labeled OEM model of the megatec branch. I tried both the megatec_usb and the blazer_usb drivers for it, with a obvious config section: [ippon] driver = blazer_usb port = auto vendorid = 06da productid = 0003 desc = "Ippon Smart Winner 3000" If I

2013/9/16 Martyn Hill <martyn.joseph.hill at gmail.com>: > Hi Arnaud and NUT team > > You may recall some time ago, I and a few others posted questions about the > above referenced (cheap and cheerful) USB-based UPS - specifically regarding > FreeBSD USB support in NUT. The original posting was entitled "Zigor Ebro > 650 compatibility". > > I've since

Hi all, I have problem with UPS from PowerWalker model VFI 2000 RT LCD over USB (didn't try serial yet). UPS should work via HID driver but ups.status is not rendered properly. Specification of UPS says USB HID compatible. HID driver is the only one which talks with UPS as i try a few from /lib/nut. I use driver usbhid-ups (which communicate with ups), but subdriver resolving is

Hi, I know it's been a topic many times here, but I've searched the archives, googled for days, and I simply don't believe, that there is still no solution to this. I'm using a PowerCom BNT-600AP ups with usb port. I've downloaded the latest version from svn, compiled it, and tried to use it: * megatec(_usb) - no luck, it did not find the UPS (I?ve read in this list, that

Use the name from ups.conf in front of "@localhost". ?The re?sult is quite different ;) root at artu:~# upsc Elit at artu Init SSL without certificate database Error: Driver not connected > What if you try nutdrv_qx without specifying megatec? (It should > autodetect.) > ?Here is the result: ? root at artu:~# upsdrvctl start Network UPS Tools - UPS driver controller

Hello all, been 5 years since I posted on this list, glad to be back :) I have a number of X-power Tigra 1kVA online UPS units. From some knowledgeable folks working for the local distributor, I learnt that from inside this looked like a Best 610 ups unit. Before, I had this UPS hooked via serial to my Windows 2003 server. For monitoring, some winpilot/upspilot software was also provided.

<nut-upsuser at lists.alioth.debian.org> I am doing my best to avoid have to spend $280 for a network monitoring card to put into a $190 UPS just to have some good remote monitoring capabilities. Rather, I would like to monitor my many 1U Tripp Lite's on my network using a Raspberry Pi running Raspian and using NUT. However, I cannot seem to get it working. And I while the hardware

Hello There, I tried your advice and i don't think it works either, See the logs, " /tmp/nut# ./drivers/usbhid-ups -DDDDDD -d1 -s test -x port=auto -x vendorid=... -x productid=... -x subdriver=... Network UPS Tools - Generic HID driver 0.52 (2.8.0-2557-g81fca30b2) USB communication driver (libusb 1.0) 0.46 ?? 0.000000??? [D3] main_arg: var='port' val='auto' ??

<facepalm ;)> the ellispis "something=..." were supposed to be replaced by your device ID numbers, etc. On Sat, Sep 23, 2023, 18:26 FatGear <fatgear1 at free.fr> wrote: > Hello There, > > I tried your advice and i don't think it works either, > > See the logs, > > " > > /tmp/nut# ./drivers/usbhid-ups -DDDDDD -d1 -s test -x port=auto -x

Hello, i've a problem, this is my configuration: - Atlantis Land UPS with serial port - a generic RS232 to USB cable adapter (QinHeng Electronics HL-340 USB-Serial adapter for linux). The problem is in the syslog file where i find: [...] Aug 19 09:07:25 ProLiant megatec[1126]: Communications with UPS lost: No status from UPS. Aug 19 09:07:26 ProLiant megatec[1126]: Communications with UPS

Hi, There seems to be a problem turning of the inverter on a Mecer online 1000VA UPS. OS: Debian Wheezy Nut: Installed via apt - version 2.6.4-2.3 Debug output from driver. root at proxmox1:~# /lib/nut/blazer_usb -DDDDD -a mecer -k Network UPS Tools - Megatec/Q1 protocol USB driver 0.08 (2.6.4) 0.000000 send_to_all: SETINFO driver.parameter.port "auto" 0.000023

Hi list, on my previous (lenny or squeeze) machine, I had it up and running, but that machine and configs are gone - and on my new jessie machine (see device and config details below) I cannot start the driver: # /lib/nut/bestups -DDDDD -a Patriot_Pro_II_750 0.000000 debug level is '5' 0.000806 send_to_all: SETINFO device.type "ups" 0.000842 send_to_all:

Hello Charles, Thanks for the feedback. I will try to answer some of these questions: > 09AE/0001 is essentially a USB-to-serial converter, and is not > compatible with usbhid-ups. (Theoretically, we could have a companion > driver that talks the same protocols over a real RS-232 port, but the > hardware I used to develop the tripplite_usb driver only has a USB > port.) Ah, that

No progress has been made: cable is UPS - PC 6 - 3 7 - 5 9 - 2 for ./blazer_ser -DDDDD -a infosec 0.000000 send_to_all: SETINFO driver.parameter.port "/dev/ttyS1" 0.000323 debug level is '5' 0.103068 send_to_all: SETINFO device.type "ups" 0.103104 send_to_all: SETINFO driver.version "2.7.3" 0.103118 send_to_all: SETINFO

Hi to everyone! I'm posting here after digging around the nut-upsuser and nut-upsdev mailing list, hoping I didn't miss something important. I'm trying to make my ups working with nut: it's a Tecnoware ERA LCD 0.85 which uses the so-hated UPSilon 2000 software to connect via usb. Personally I checked and seems that this junk software only works from windows, I'm trying to

Hi, I'm running the latest version of NUT and with the above UPS and I keep getting the following error: "tripplite_usb[3308]: Error reading B value: Device detached? (error 0: could not claim interface 0: Device or resource busy)" The device keeps disconnecting and re-connecting until fails. I've tried to see if others are getting this - but I could not locate a

Hi, I'm using macports to install nut on a MAC OS X (10.7) I get the following error messages when I try running: sudo blazer_usb -a zigor -DDDDDDDDDD 0.944590 Checking device (0001/0000) (250/005) 2.785449 - VendorID: 0001 2.785465 - ProductID: 0000 2.785468 - Manufacturer: unknown 2.785472 - Product: STD UPS MON V1.0 2.785475 - Serial Number: unknown