similar to: No subject

Gentlemen, I just had time to start looking at the latest version of the development tree. I have built the apc-hid part of newhidups from the development tree and I am in the process of testing it with my "Back-UPS ES 650". As of right now I have incorporated the attached changes to apc-hid.c. I have been using the corresponding changes together with some changes from Arnaud with the

Gentlemen, I have now had a chance to run some initial tests of my changes to apc-hid.c of the current development tree. Running newhipups and inspecting the -DDDD output seems to indicate that with the fix below everything seems to work as expected. However, I have not yet shut my system in order to take the UPS out of action so that I can do my various tests with a lightbulb load. I still hope

Gentlemen, I have determined that on my UPS (APC Back-UPS ES 650 FW:818.w1.D USB FW:w1), the variable UPS.PowerSummary.RemainingCapacityLimit is writeable. I am setting this variable to start shutdown a little earlier. Appended is an unconditional patch for apc-hid.h. If, as indicated by the original code, there are APC UPS devices that don't allow setting of this variable, it becomes

Hi, This might be a simple thing to fix, but I can?t figure it out. We replaced the battery for the first time in our Eaton 5PX a couple of weeks ago, but we haven?t been able to clear the ?ups.alarm: replace battery!? status. Details of our installation are: OS: Debian 6 NUT version: 2.7.4 Installation method: from source tarball UPS device: Eaton 5PX2000IRT, 240V, 1800W, 2000VA, bought in

I suspect that the battery is failing on my Pulsar Evolution 500 (it is several years old now) but I can't seem to get a valid battery voltage from the UPS. The following tests were done using NUT 2.2.1, but I first noticed this with the trunk, and reproduced it with the current branches/Testing as well. The only two values I have seen for battery.voltage are 120.0 and 119.0, e.g.: $ upsc

To all, I attempted to configure the UPS tools for the Tripp-Lite SmartOnline 1500VA 2U rackmount UPS. I followed the instructions from the 'upsdrvctl start' output and posted the diagnostic information below. Is my UPS using an unknown product ID as reported? From the mailing list archive, I have found another posting for the same UPS with device model '09AE/4003', whereas

When running 'sudo upsmon -c fsd' UPS turns off then back on after a delay as expected. But when power is disconnected and the command is ran, the UPS turns off but still turns back on again. Changing 'ondelay' to -1 or 0 does not change the behavior. How can I get the UPS load to stay turned off if there is no power? Or am I misunderstanding how to test this functionality?

Hi there, OS: (L)ubuntu 12.04 precise LTS Nut: 2.6.3-1ubuntu1.1 Installation Method: Package (apt-get install nut) Hardware: HP R1500 G3 INT Hardware-Specs: http://h18004.www1.hp.com/products/quickspecs/14059_div/14059_div.pdf Problem: I tried to set up nut with our new arrived HP R1500 G3 UPS but there is a failure with the usb connection. After trying "/lib/nut/usbhid-ups -DD -a

Thanks for your help. From: Charles Lepple <clepple at gmail.com> Date: Mon, 18 Dec 2017 19:26:56 -0500 This may sound like an apples-to-oranges comparison, but we did uncover an issue with CyberPower UPSes where the delay values needed to be greater than or equal to 60 (seconds), since they were being rounded down to integer numbers of minutes internally: What was the largest

On 6/28/20 4:25 AM, Scott Colby wrote: > Hello, > > I am having difficulty using NUT to shut down my Netgate SG-1100 > (a pfSense router) when the power level of the UPS gets critically > low. > > Here is some relevant information: > - OS: pfSense 2.4.5-RELEASE-p1 (FreeBSD 11.3-STABLE) > - NUT version: 2.7.4 > - Installed from: pfSense package 2.7.4_7 > - UPS:

It's been a while since I tried to use NUT, so I thought I would give it another try. Big trouble. The UPS is a Tripp-Lite AVR 550U. It has only a USB connector. The computer is running Red Hat Enterprise Linux 4. I just installed NUT version 2.2.0. I'm going through the steps in the INSTALL document. # cat ups.conf [igor] driver = usbhid-ups port = auto

Hi, With recent revision, it's impossible to get upsdrvctl started: [root at teevee nut]# /usr/local/bin/upsdrvctl start Network UPS Tools - UPS driver controller 2.3.0-1352 Network UPS Tools: 0.29 USB communication driver - core 0.33 (2.3.0-1352) Warning: This is an experimental driver. Some features may not function correctly. Using subdriver: TrippLite HID 0.2 (experimental)

Hi, I have a HP R1500 G2 UPS and want to get it working under Debian Lenny - as this OS is not supported by HP I'm trying to use nut for it - but I can't get it working. Do I have any chance to get the UPS running with nut. I also tried different drivers but had no luck either. Or does anyone has experience with HP UPS under debian ? Any help would be nice ! I tried /lib/nut/usbhid-ups

I have a Tripp-Lite BCPERS450, connected to a system running Ubuntu 16.04.3 LTS and NUT 2.7.2-4ubuntu1.2. I had to make my own /lib/systemd/system-shutdown/nutshutdown, but now everything is working except for powering on and off the UPS. Regardless of the settings of offdelay and ondelay in upsconf, and regardless of whether the AC power is on, when I say "upsdrvctl shutdown" the UPS

I am having an issue running NUT and using an TrippLite OMNI900LCD. When I run ./upsdrvctl start I get : [player@V0002-S002 bin]$./upsdrvctl start Network UPS Tools - UPS driver controller 2.1.0 Network UPS Tools: 0.28 USB communication driver 0.28 - core 0.30 (2.1.0) Detected a UPS: Tripp Lite /TRIPP LITE UPS Using subdriver: TrippLite HID 0.1 (experimental) dstate_setflags: base variable

My UPS is connected to a Raspberry Pi by USB. After a few hours of working, the service fails. Looking at kernel messages I noticed that the device is repeatedly disconnecting and reconnecting. I have tried using a different USB port and using a brand new USB cable. I have not had success by changing config parameters like pollfreq/pollinterval/etc. What is causing the UPS to keep disconnecting?

Hi I would like to be able to use this UPS with NUT please ? Product id = 53962KX Network UPS Tools - Generic HID driver 0.38 (2.7.2) USB communication driver 0.32 0.000000 debug level is '2' 0.002761 upsdrv_initups... 0.014996 Checking device (03F0/0024) (001/005) 0.032670 - VendorID: 03f0 0.032790 - ProductID: 0024 0.032955 - Manufacturer:

Does the following error message have a specific meaning: usb 1-1: usbfs: USBDEVFS_CONTROL failed cmd usbhid-ups rqt 161 rq 1 len 2 ret -75 I get two of these messages every time I run the following: /lib/nut/usbhid-ups -u root -DDD -a trippy The following is the output from the above command: debug level is '3' Checking device (0000/0000) (004/001) - VendorID: 0000 - ProductID:

Thanks for the quick response! On Sat, Jun 27, 2020, at 22:17, Manuel Wolfshant wrote: > On 6/28/20 4:25 AM, Scott Colby wrote: > > Hello, > > > > I am having difficulty using NUT to shut down my Netgate SG-1100 > > (a pfSense router) when the power level of the UPS gets critically > > low. > > > > Here is some relevant information: > > - OS:

Hello, I am having difficulty using NUT to shut down my Netgate SG-1100 (a pfSense router) when the power level of the UPS gets critically low. Here is some relevant information: - OS: pfSense 2.4.5-RELEASE-p1 (FreeBSD 11.3-STABLE) - NUT version: 2.7.4 - Installed from: pfSense package 2.7.4_7 - UPS: AVR750U (Device release number 2) - I have included my config files, output from `upsc`, and