similar to: [HCL]

Hi, recently I got a GE EP6000R UPS. At first I feared it's not supported at all, but after digging in I found out that it's supported by the 'blazer' driver. The UPS has both RS232 and USB connection. To use the RS232 connection, I had to use the 'cablepower = none' as the UPS is using only RX, TX and GND pins. So my 'usp.conf' was a bit like that: > [myups]

Hi, I just got two new UPS's - GE EP6000R. These have both RS232 and USB connection. As far as I could detect these are not supported by NUT. However, they provide some Linux software and as long as these UPS's are not in production (another week or so) I could 'play' with them to try to get some protocol information. Though I would need some pointers on how to do it... Mind you

Hi, I got a bright idea to monitor CPU core temperature using ''lm_sensors''. I was testing on my quad-core desktop machine and everything seemed great. However - my Domain-0 has just two VCPU''s assigned to it and this is exactly what ''sensors'' report. Any ideas about how to work around that besides letting Domain-0 use all CPUs? Regards, Danilo

Got a problem after upgrading Samba from 3.0 to 3.5 - have a bunch of users and groups in LDAP and things work for the most part. However, when people try to change permissions from within Windows, some usernames or groupnames are shown properly, but other are not - they see the SID. Following up I noticed, that I can get a list of all users with 'wbinfo -u' and that I can get a SID for

Here is my setup. samba+winbind on OpenSuse 11.3 (samba 3.5.4). Using winbind to auth to another samba+ldap server. Authentication works until first failed login: host:~ # wbinfo -a prod\\user%goodpass plaintext password authentication succeeded challenge/response password authentication succeeded host:~ # wbinfo -a prod\\user%badpass plaintext password authentication failed Could not

Hello Everyone! Been looking around the internet but have not found a solution for my problem yet, all i found was a report on opensuse forums with no replays. I have a Xen dom0 running on OpenSuse 11.4 x86_64, on this I’ve created 3 PV instances all running OpenSuse 11.4 x86_64 as well. All 3 PVs were installed the same way with the same package selection and only ONE of this 3 PVs hangs at

Hi, I have two identical UPS's on USB bus. The original machine I was going to use for UPS monitoring only had had USB bus, so these two UPS's were seen like that: Bus 001 Device 009: ID 14f0:00c9 Bus 001 Device 007: ID 14f0:00c9 There was no description on the right side either. If I used the 'verbose' flag, both UPS's had the exact same output... I since replaced the

Lyonn CTB-1200 root at frambuesa:~# upsc lyonn at localhost battery.voltage: 27.20 battery.voltage.nominal: 24.0 beeper.status: enabled device.type: ups driver.name: blazer_usb driver.parameter.pollinterval: 2 driver.parameter.port: auto driver.version: 2.4.3 driver.version.internal: 0.03 input.current.nominal: 5.0 input.frequency: 49.9 input.frequency.nominal: 50 input.voltage: 213.3

Hello, I'm sorry if i'm not sending to the good email adress, please transfer this mail to the good one if necessary... I have tested and run the driver named "blazerd_usb" with differents products from the infosec company (tested on the following UPS : X2, X3, X4, E2, E3, E4) Is it possible to add the to the Hardware compatibility list ? Thank you, Regarde, Jeremy

Hi, another UPS piece supported by blazer_usb: ALLSAI model LV 2K upsc output: battery.voltage: 82.08 battery.voltage.nominal: 72.0 beeper.status: enabled device.mfr: device.model: LV 2K device.type: ups driver.name: blazer_usb driver.parameter.pollinterval: 2 driver.parameter.port: auto driver.version: 2.4.3 driver.version.internal: 0.03 input.current.nominal: 18.0 input.frequency: 59.9

Hi All! Just an update! The snmp driver seems quite happy with an APC AP9618 managment card in an APC Smart-UPS RT 5000 XL UPS. I have an APC AP9630 to test in the near future so will give and update on that one too! Cheers Ang -- Angela Williams angierfw at gmail dot com Linux/Networking Hacker Blog http://angierfw.wordpress.com Smile! Jesus Loves You!

2011/11/5 Arnaud Quette <aquette.dev at gmail.com> > Hi Greg, > > 2011/11/4 Charles Lepple <clepple at gmail.com> > >> On Thu, Nov 3, 2011 at 12:23 AM, Greg Trounson <gregt at maths.otago.ac.nz> >> wrote: >> > These Socomec units have RS-232 connectors and claim to support JBUS. >> > On the nut compatibility page I only see one Socomec

Atlantis Land A03-P551(V1.2) battery.charge: 100 battery.voltage: 13.70 battery.voltage.high: 13.00 battery.voltage.low: 10.40 battery.voltage.nominal: 12.0 device.mfr: device.model: device.type: ups driver.name: blazer_usb driver.parameter.langid_fix: 0x0409 driver.parameter.pollinterval: 2 driver.parameter.port: x driver.version: 2.6.4 driver.version.internal: 0.08 input.current.nominal: 0.0

Greets... ..just bought a cheap UPS today, works in debian 7.0 wrt nut 2.6.4 using richcomm_usb driver... ....output of upsc..... //// root at debian7:~# upsc starpower at localhost device.mfr: Richcomm dry-contact to USB solution device.model: UPS USB MON V1.4 device.serial: unknown device.type: ups driver.name: richcomm_usb driver.parameter.pollinterval: 2 driver.parameter.port: auto

On Aug 7, 2013, at 10:43 AM, Matthew Lenz wrote: > Tripp Lite SMART1300LCDT > > # upsc ups [...] > battery.voltage: 0.0 > battery.voltage.nominal: 24.0 [...] > input.frequency: 5990.0 > input.transfer.high: 150.0 > input.transfer.low: 92.0 > input.voltage: 0.0 > input.voltage.nominal: 120 > output.current: 100.00 > output.frequency: 5990.0 >

On Aug 8, 2013, at 9:14 AM, Matthew Lenz wrote: > On Wed, Aug 7, 2013 at 6:47 PM, Charles Lepple wrote: >> Could you please stop the NUT services (or just the driver, whatever is easiest) and run "sudo /lib/nut/usbhid-ups -a ups -DDD" ? > > How much output would you like from this? Want me to just stick it on > a pastebin somewhere? > Just a few kB from the

On Thu, Aug 8, 2013 at 6:27 PM, Charles Lepple wrote: > On Aug 8, 2013, at 9:14 AM, Matthew Lenz wrote: > >> On Wed, Aug 7, 2013 at 6:47 PM, Charles Lepple wrote: >>> Could you please stop the NUT services (or just the driver, whatever is easiest) and run "sudo /lib/nut/usbhid-ups -a ups -DDD" ? >> >> How much output would you like from this? Want me to

Syndome Era Series *upsc output* * *battery.charge: 100 battery.runtime: 1000 <-- not reported by UPS (guesstimate) battery.voltage: 13.60 battery.voltage.high: 13.00 battery.voltage.low: 10.40 battery.voltage.nominal: 12.0 device.type: ups driver.flag.novendor: enabled driver.name: blazer_usb driver.parameter.chargetime: 43200 driver.parameter.idleload: 30 driver.parameter.pollinterval: 5

CyberPower Battery Backup with Surge Protection, model LE825G Appears to function properly with the driver listed on the HCL for the Cyber Power Systems ups 2 685AVR USB (usbhid-ups). Tested with shutdown mode "UPS Goes On Battery" with a 5 second timer and the system successfully shutdown as expected. upsc output: upsc ups battery.charge: 100 battery.charge.low: 10

Digitus DN-170014 root at home:/home/scripts# upsc ups device.mfr: Richcomm dry-contact to USB solution device.model: UPS USB MON V1.4 device.serial: unknown device.type: ups driver.name: richcomm_usb driver.parameter.pollinterval: 2 driver.parameter.port: auto driver.version: 2.6.4 driver.version.internal: 0.04 ups.mfr: Richcomm dry-contact to USB solution ups.model: UPS USB MON V1.4