similar to: Liebert PSP

On 10/01/2015 00:45, Charles Lepple wrote: > On Jan 8, 2015, at 11:43 PM, Graham Menhennitt > <graham at menhennitt.com.au <mailto:graham at menhennitt.com.au>> wrote: > >> Hello Nutters, >> >> I'm running nut 2.7.2 on FreeBSD 10-stable (via the FreeBSD port) >> with an APC Back-UPS CS 350 connected via USB. I get persistent >> (every few

OS name and version: FreeBSD 9.0-RELEASE amd64 exact NUT version: 2.6.1 NUT installation method: >From ports collection (cd /usr/ports/sysutils/nut; make install) Exact device name and related information: American Power Conversion/Back-UPS ES 525 FW:851.t2.I USB FW:t2 Complete problem description: /usr/local/etc/rc.d/nut start Network UPS Tools - UPS driver controller 2.6.1 Network UPS

To all, I attempted to configure the UPS tools for the Tripp-Lite SmartOnline 1500VA 2U rackmount UPS. I followed the instructions from the 'upsdrvctl start' output and posted the diagnostic information below. Is my UPS using an unknown product ID as reported? From the mailing list archive, I have found another posting for the same UPS with device model '09AE/4003', whereas

Hello. Not listed as supported, so here is some info, [root at vhost ~]# /usr/sbin/usbhid-ups -DD -a powercom Network UPS Tools - Generic HID driver 0.38 (2.7.2) USB communication driver 0.32 0.000000 debug level is '2' 0.001318 upsdrv_initups... 0.074753 Checking device (0529/0001) (003/002) 0.074835 Failed to open device, skipping. (Permission denied)

I'm trying to set up nut-2.6 with a SMX1000 ups unit from APC on a CentOS 4.8 server. It's connected via USB, and Linux has detected it as a HID device. Nut was built from source code. T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 21 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=051d ProdID=0003 Rev= 1.06 S: Manufacturer=American Power

Apologies for resurrecting an old thread and likely poor formatting - I wasn't subscribed to the list at the time and have copied it out of the archives (http://lists.alioth.debian.org/pipermail/nut-upsuser/2010-July/006104.html). I've been unable to locate any further progress on this UPS (Liebert 10af:0001) - a thread from 2009

> On Sep 11, 2016, at 3:37 PM, Jeff Bowman <jeff.bowman at intexx.com> wrote: > > > > Using subdriver: APC HID 0.95 > > > > ...and then hangs for 45 seconds before returning to a command prompt. No > UPS hardware information is printed. > > It can take about that long to read the descriptors. The non-Windows NUT > drivers will print that message,

Hi, I have a HP R1500 G2 UPS and want to get it working under Debian Lenny - as this OS is not supported by HP I'm trying to use nut for it - but I can't get it working. Do I have any chance to get the UPS running with nut. I also tried different drivers but had no luck either. Or does anyone has experience with HP UPS under debian ? Any help would be nice ! I tried /lib/nut/usbhid-ups

Thanks for the reply. However these two FAQ are unfortunately not describing the situation. - The first issue is that NUT switches off the UPS upon reboot on low battery (not that it dies because of low battery) - The second issue is that the UPS does not recognise being online again (not that the PC does not restart) Sent from my iPhone > On 11 Jun 2019, at 02:03, Charles Lepple <clepple

Hello all, About a month ago Peter and Charles were kind enough to try to help me with getting a Tripp Lite USB UPS to work with NUT. I reported quite a bit of initial success, and then other things here fell apart. Between work, fence building and a week-long out of town business trip, I have had to drop this from my list of things to do lately. I am back at it, and I believe I will have

Hi there, OS: (L)ubuntu 12.04 precise LTS Nut: 2.6.3-1ubuntu1.1 Installation Method: Package (apt-get install nut) Hardware: HP R1500 G3 INT Hardware-Specs: http://h18004.www1.hp.com/products/quickspecs/14059_div/14059_div.pdf Problem: I tried to set up nut with our new arrived HP R1500 G3 UPS but there is a failure with the usb connection. After trying "/lib/nut/usbhid-ups -DD -a

Hello, I've recently bought Ippon Smart Winner 3000 New (note the "New" in the model name) and I can't make NUT to work with it. Linux gateway 3.17.8-gentoo-r1 #1 SMP Mon Feb 16 13:46:11 MSK 2015 x86_64 Intel(R) Celeron(R) CPU 1037U @ 1.80GHz GenuineIntel GNU/Linux Network UPS Tools 2.7.2 1) USB connection partially works using usbhid-ups driver, the problem is that I

Hi! Info OS: TinyCore Linux 4.5.6 NUT version: 2.6.4 NUT innstallation method: source tarball Device name: Eaton Ellipse ups eco 1600 usb din (EL1600USBDIN) /usr/local/ups/etc/ups.conf file: [eaton] driver = usbhid-ups port = auto When I run: root at Dalen:/usr/local/ups/bin/upsdrvctl start eaton I get this error message: Network UPS Tools - UPS driver controller 2.6.4

Hello to All. OS : FreeBSD NAS 9.1-STABLE FreeBSD 9.1-STABLE [uname -a] Version : Network UPS Tools upsd 2.6.5 [upsd -V] Installation method : build into FreeNAS 9 UPS : APC Back-UPS 500 BK500EI USB Today i install FreeNAS and try to connect to it my UPS APC Back-UPS 500 BK500EI via USB with no luck;/ If anyone can try to help me I would be grateful. My configs nut.conf : MODE=standalone

Charles, It starts out good, then goes into a Connection timed out loop. If I can provide any information to fix a driver I'll do my best. Here's the output: # /usr/local/ups/bin/usbhid-ups -DD -a eaton Network UPS Tools - Generic HID driver 0.41 (2.7.4) USB communication driver 0.33 0.000000 debug level is '2' 0.002550 upsdrv_initups... 0.288229 Checking device

Hello, I am hoping someone can point me in the right direction. I am setting up a new UPS, most things seem to be working except the UPS turns off immediately during a test shutdown using///"//upsmon -c fsd".//No delay before the UPS turns itself off leaving no time for the server to shutdown properly. I have attempted to set the delay higher using "upsrw -s

Hello, I have been using NUT for a short period of time and have some questions regarding the UPS reboot signal that I can't figure out. Have tried some googling and reading the DOCs but I am struggling to understand how some variables / things are supposed to work, so would appreciate any help with any of the following questions. I am running NUT on standalone mode on a linux machine

My UPS is connected to a Raspberry Pi by USB. After a few hours of working, the service fails. Looking at kernel messages I noticed that the device is repeatedly disconnecting and reconnecting. I have tried using a different USB port and using a brand new USB cable. I have not had success by changing config parameters like pollfreq/pollinterval/etc. What is causing the UPS to keep disconnecting?

On Jun 10, 2019, at 2:32 PM, Marc Finns wrote: > > Hello, I read all FAQ and other sources but I could not find this situation, so I thought of asking the experts. > I successfully configured a Raspberry NUT server to control my UPS that powers several devices (NUC with ESXI VMs, Synology NAS etc). > All works well in principle, but I have the following behaviours that I could not

Hi I would like to be able to use this UPS with NUT please ? Product id = 53962KX Network UPS Tools - Generic HID driver 0.38 (2.7.2) USB communication driver 0.32 0.000000 debug level is '2' 0.002761 upsdrv_initups... 0.014996 Checking device (03F0/0024) (001/005) 0.032670 - VendorID: 03f0 0.032790 - ProductID: 0024 0.032955 - Manufacturer: