similar to: Call parking question

i've got the parking lot set up in asterisk 1.6.2.8. when a caller calls into the pbx and connects to an extension, the answering extension can place the person into the parking lot by dialing #72 during the call via the parkcall parameter in features.conf. this works just fine. however, when another extension picks up the call from the parking lot (e.g, by dialing x701), that extension

Hello All, I have a issue with park and pickup feature. I have asterisk 1.4.35 branch, Here is the scenario for the park and pickup. I have changed parking feature with *72 for my asterisk in features.conf. When i have inbound call it comes to one extension or ring group and then I put that inbound call in parking. After that I will dial some extension to get that call back, I am using

Hi all, Is there anyway you get Asterisk to let you park a call a second time via pressing the # key + 700 (or whatever is in features.conf) ? If you get a call out of the parking lot & hit # again it just sends the DTMF tone down the line and nothing happens.. A few posts have hinted that you cannot blind transfer a parked call, but surely there must be some way around this as I can

Hi, I'm having trouble to figure out how I could implement this feature : "When on call with a contact, local operator would dial a sequence which would park the remote party to a specific parking slot, among the hundred of existing slots. (to each extension, a single specific parking slot is attached and there are too many extensions to dedicate BLF or short DTMF sequence to each)

Hi List, I have a client who is using park heavily, but once we hit the cal button (in this a hotkey tied to park orbit on the Snom's), we have a 3 second delay before we here the digit the call is parked on. Is their anyway around this at all? Does anyone know if we have these same delays if using the DTMF digits? Any suggestions would be great! Thanks! -------------- next part

Trouble in Parking Paradise! Good Day all, I have a situation that I have tracked as far as I can take it and am looking for assistance into the matter. My setup.. Asterisk 1.0.1 with the AMP config environment. When I have auto attendant answer the phone and I dial my extension "2204" The call come through and If I park it it gets place into extension 701 (the first parking

I've got a situation where I need to use a transfer to the parking lot as hold, but am not going to use BLF indicators on the phone to pick up the parked calls so I need to hear the 3-digit extension after the transfer. I'm using Snom 300 phones and have tried setting a programmable button to Key Event F_TRANSFER 700, which successfully does the transfer but cuts off audio so you

Hi: I want to make parking calls easier for my hard-working users. Is there a way to make the Polycom call park feature work with Asterisk? In case it just works out of the box, I haven't tried it yet; but the "call park" feature isn't enabled on the Polycom phones by default. -Stephen-

One more Polycom IP601 question please (sorry for the long intro here to document) ... In order to closely approximate the behavior of the previous telephone system that many of the users are familiar with, I have set up call parking like this: - features.conf [general] section contains: parkext => ** ; What extension to dial to park parkpos => 10-11 ; What

Hi I'm trying to get the rebuilt parking functionality to work in Asterisk 12.0.0. In Asterisk 11.6.0 I managed to get a call to get parked by adding a dynamic feature in features.conf for the DMTF sequence *# which called a macro in extensions.conf, which then runned the ParkAndAnnounce application, and the call got parked. The syntax for ParkAndAnnounce I used was this (I don't

I'm trying to get call parking working with the lighted buttons on the SNOM 200. I have set the 5 buttons to "Park Orbit", for extensions 700-704. Pressing the first button (x700) does park the call. However, the remaining buttons (x701-704) don't allow me to pick up parked calls, or show parking status via the LEDs. I can only pick up parked calling by manually dialing the

>From discussions with the receptionist staff, this is what we need: X number of buttons for parking slots. These buttons should be lit when a call is parked there. When on a call, just pushing an unlit button will park the call. (The do not want to hit hold, transfer, etc.) Hitting Transfer and the button would most likely be OK. To pick up a call, they can push the parking slot button. The

I can't seem to retrieve a parked call. Here is what I do: Call from phoneA to phoneB Answer phoneB Press Flash/Callwait on phoneB Press 700 to park the call A voice says that the call is parked at 701 When I try to dial 701, I don't get connected to the parked call Below is the asterisk output when I tried to park

Hi, Is there a way to do a blind transfer within an asterisk dialplan (like '##')? The reason I need this (I think) rather than a regular Goto() is that I'm trying to do one-touch parking. I can park a call using one-touch parking and then pick it up again, however if I try to re-park the call, it gets lost. I think that is because asterisk thinks I'm still on the park extension.

I have an issue with call parking and hope there is some undocumented feature for this. ;-) We are replacing our legacy PBX with asterisk, but to save money over time (handsets and network), I am trying to maintain the use of our legacy PBX. Asterisk extensions can not use the call parking features (not usable over trunk cards) of the old PBX, so I have to get the old PBX to use asterisk's.

I have put canreinvite=no for all my internal SIP-clients in sip.conf because I want Asterisk to be in the middle of the RTP-stream so he can provide MusiconHold and so... Now, what the Asterisk CLI tells me when I make a call from my one internal SIP-phone to another internal SIP-phone is : Verbosity is at least 25 == Spawn extension (intern, 51, 1) exited non-zero on

Hello Users I'm Doing working on Both OpenSER and Asterisk ....... 9001 and 9003 are registered in OpenSER in extension.conf [from-sip] exten=>115,1,Park() exten =>115,2.Hungup() in Feature.conf ( default park no 701) in sip.conf [9001] ... .. [9002] [9003] When 9003 dial the 115 ( Parking itself) , Asterisk Server says " U parked on 701 extension " After When 9001 dial

That is how many old PBX phone systems work and it is that way our users are used to working with the phone system. Another issue with the way Asterisk callparking currently works is that there is only one call-park orbit, you cannot use a different set of numbers for a different call park instance(i.e. 700 goes to 701-720 AND 740 goes to 741-750). We also have several Grandstream phones which

Hello, I am trying to create a dynamic call parking lot using https://wiki.asterisk.org/wiki/display/AST/Application_Park But this manual is not enough to fix my problem : Asterisk keeps trying to park the call in the default parking lot : [Jul 2 11:32:14] -- Executing [3333 at from-770000:5] Set("SIP/testacc77000-00000002", "PARKINGDYNAMIC=parkinglot_test") in new

Hi, Been playing with Call parking, and I can`t help but wonder if I am doing something incorrectly. The way I understand it (using default config in features.conf), is I would transfer a call to extension 700, which would park the call, tell me "701". I could then hang up, go fetch the fright person and tell him "call 701 you have a call waiting for you". The way I