similar to: Sangoma U100 failing every Monday - USB port problem or Wanrouter issue?

Hi everyone, I am reading through Sangoma Wiki right now. But someone may already and quickly notice this. I have a system that is down since the morning (maybe power intruptions). All seems fine except for "wanrouter status" shows disconnected. Following are the alarms raised. Should I call telco (they have long wait times) or should I just keep searching online for troubleshooting

I have installed Asterisk on a CentOS4 box and then installed Asterisk from CVS. I installed a Sangoma A101 and connected it to a Adtran 600 using a T1 Crossover cable. The 600 has 12 x FXS, 12 x FXO interfaces. I ran through the wanpipe install instructions and configured it, now I can run [root@altpbx asterisk]# wanrouter hwprobe ------------------------------- | Wanpipe Hardware Probe Info

Trying to install wanpipe 3.5.18. No errors during compile. But when I reach the point where wanpipe and dahdi_cfg is started, I encountered an error. Starting WAN Router... Loading WAN drivers: wanpipe done. Starting up device: wanpipe1 wanconfig: WAN device wanpipe1 driver load failed !! : ioctl(wanpipe1,ROUTER_SETUP) failed: : 22 - Invalid

Hey Guy, I have ubuntu 10.04 64bit and compiled dahdi / wanpipe 3.5.19 /asterisk-1.8.x I didn't understand what is the relation between wanpipe and dahdi ? do i need to start wanrouter service ? I am getting weird errors and my system got kernel panic many time when i restart dahdi service. any idea ? what is the startup sequence of all these service ? root at example:/etc/asterisk#

Hi, Does anybody have an idea as to why dahdi_test results drop to unacceptable levels after doing a wanrouter stop/start using a Sangoma card? See below that it drops from 99.99% to 98.55%: [root at bin]# dahdi_test Opened pseudo dahdi interface, measuring accuracy... 99.999512% 99.992874% --- Results after 2 passes --- Best: 100.000 -- Worst: 99.993 -- Average: 99.996193, Difference:

I've been using Asterisk 1.2.6 with a 4 port FXO Sangoma A200 card for the past month without many problems (other than the fact that the Sangoma card doesn't disconnect hung up calls immediately, which I posted about in another thread, and has still not been fixed), however, I had a call from one of our clients today and they complained that our phone system kept ringing through when they

Hi, Has anyone ever experienced crosstalk with sangoma analogue cards on 64bit? We have exhausted every test to try and replicate this and find a solution with Sangoma tech support, but we can not fix it. We are about to try the card and four *seperate* UK BT lines in a 32bit system. The current system is a 4gb, dual core cpu with pbx in a flash 1.4, Zaptel and Asterisk 1.4.21-2 Currently we

I upgraded from Tormenta2 to Sangoma A101. I followed the instructions, and installation was successful. zttool, ztcfg, all show card is installed properly. I copied the parameters from my old working zaptel.conf, zapata.conf and zapata-auto.conf. Verified on Sangoma website that these files are correct. Also configured wanpipe1.conf. But doing all this didn't start the PRI channels. It says

Hello, We are having issues with a NEW Sangoma A108D: -- Executing [691918892 at pbx1:1] Dial("SIP/xtravoip200-009d24b0", "DAHDI/g0/691918892|30|m") in new stack [Oct 1 10:04:43] WARNING[14171]: channel.c:3170 ast_request: No translator path exists for channel type DAHDI (native 76) to 256 [Oct 1 10:04:43] WARNING[14171]: app_dial.c:1237 dial_exec_full: Unable to create

Hi All, I have just latest branch of asterisk 1.8 and i didn't found dahdi command in CLI everything seem fine. am i missing something ? campbx2*CLI> dahdi <tab tab> No such command 'dahdi' (type 'core show help dahdi' for other possible commands) campbx2*CLI> root at campbx1:/etc/wanpipe# wanrouter hwprobe ------------------------------- | Wanpipe Hardware

Hi, I have A101DE Sangoma Card( http://www.sangoma.com/products/hardware_products/digital_voice_and_data_networking/a101.html ) lspci shows as 03:04.0 Network controller: Sangoma Technologies Corp. A200/Remora FXO/FXS Analog AFT card [root at asterisk ~]# lspci -vvv -s 03:04.0 03:04.0 Network controller: Sangoma Technologies Corp. A200/Remora FXO/FXS Analog AFT card Subsystem: Unknown device

Im trying to install and configure sangoma ... every thing is OK but when type the command "wanrouter start" the following error apears: wan Driver not found. Thanks for any help

Hi, I recently purchased an MSI Wind Netbook, just slightly bigger than an EeePC, and IMHO just one step above the mere toy category. It's got a 10" monitor, 80 GB SATA HD, and the keyboard is just big enough so I can type with ten fingers (with a little exercise). The thing came preinstalled with Windows XP, and I've spent the last two days figuring out how I could possibly

Hi all, My problem boils down to these errors: ... Unable to create channel of type 'ZAP' (cause 34 - Circuit/channel congestion) == Everyone is busy/congested at this time This is triggered by lines in extentions.conf such as: exten => _X.,1,Dial(ZAP/g1/${EXTEN},,W) The system is CentOS v5.2 with Asterisk 1.4.23 (druid-asterisk-1.4.23.1-2), a Sangoma A104

Hello All, I have a setup of ABE on rPath linux,Sangoma A101D, and a T-1 line (Not PRI) which is all happily coexisting and all lights are green. The T-1 comes in from the world into a "Shark Box" which splits the T into 384K data and 6 channels voice. The data side is working great. The voice side, not so great. It was originally broken out to 6 pots line and Verizon came back

Ok, I have tested with almost all versions both in 2.3.2--*-stable and 2.3.3-*-beta - I am getting same messages: May 9 10:55:26 WARNING[3961]: chan_zap.c:1925 pri_find_dchan: No D-channels available! Using Primary on channel anyway 16! and same Down state pb01*CLI> pri show span 1 Primary D-channel: 16 Status: Provisioned, Down, Active Switchtype: EuroISDN Type: CPE Window Length: 0/7

Hello, Have you tried the wanpipe-beta8c-2.3.3.tgz release in the custom/2.3.3 dir on their FTP site? Also, have you contacted Sangoma for support? They are very responsive. I am using wanpipe-beta8a-2.3.3.tgz and it's been working great on my A104 for a week now. MATT--- -----Original Message----- From: Dmitry Zhukovski [mailto:DZH@comx.dk] Sent: Monday, May 09, 2005 5:20 AM To: Asterisk

Hi again, Well - I didn't see beta8a-2.3.3 in custom dir. Will try. Also I tried to contact Sangoma - they are very fast to answer but main problem is time difference - it's 6 hours between Canada and Europe. Br, dmitry Dmitry Zhukovski System developer ComX Networks A/S Naverland 31, 2 DK-2600 Glostrup Denmark Phone: +45 70 25 74 74 Fax:???? +45 70 25 73 74 Web: www.comx.dk

Hi, I'm using Sangoma's wanpipe together with dahdi, all software downloaded today at most recent version. Hardware is Sangoma A104, a 4xE1 card. Installation went well. Anyway, wanrouter status shows a different result than dahdi_tool or dahdi_scan. I've just put a hardware loop on port 1. All the other ports are open. wanrouter status shows the expected result: Device name |

Hiya all, I have had no end of trouble trying to get my A101 E1 card working on a new asterisk installation. The sangoma tech people have ignored my emails about this. All the installation of wanpipe seems to go ok, and zaptel. it all installed compiled and does all the wanpipe hwprobe exactly as documented. Asterisk compiled ok, but when I run it give me Jun 27 11:12:18 ERROR[10528]: