similar to: Dahdi PRI T1 Setup for TE210P

I've got an asterisk 1.4.24 box with dahdi complete 2.1.0.3+2.1.0.2 I've got a 2 port T2XXP card attached with on T1 currently plugged in. Inbound calls work fine, but outbound fail with the rather cryptic: [May 19 17:28:07] WARNING[11360]: app_dial.c:1237 dial_exec_full: Unable to create channel of type 'DAHDI' (cause 0 - Unknown) There are similar threads I've found on the

Hello! I am trying to configure my digium TE220 dual-span pci express card with Dahdi. I seemed to have managed to set up the card with the Dahdi kernel, as demonstrated by executing dahdi_scan: [1] active=yes alarms=RED description=T2XXP (PCI) Card 0 Span 1 name=TE2/0/1 manufacturer=Digium devicetype=Wildcard TE220 (4th Gen) location=Board ID Switch 0 basechan=1 totchans=31 irq=16

Hi all. I have this problem with my Digium 2E1 card and PRI, for hours It works well, with some meesages... [Aug 10 09:20:31] NOTICE[32270] chan_dahdi.c: PRI got event: HDLC Abort (6) on Primary D-channel of span 1 But PRI continue up....hours later... PRI go down. I thought the problem was in the telco, but the strange thing is that I have a loop cable in the second E1 and when I scan both E1

I have a box with 12 T1s (4 Te410P cards). The PSTN provider is reporting slips and ask me to update the clock source. I have my system.conf set as the following but when I run dahdi_scan only the ports on Card 1 are showing up with syncsrc=1 system.conf : span=1,1,0,esf,b8zs bchan=2-24 mtp2=1 span=2,2,0,esf,b8zs bchan=26-48 mtp2=25 span=3,3,0,esf,b8zs bchan=49-72

Hi everybody, I have a 1.6.0.5 asterisk system and I?m having many problems with my pstn cards. This system has a Digium B410P with 4 BRIs configured, and an OpenVox A400E. The issue is that it?s impossible to make the system recognize the A400E, despite the ?lspci? output is: 0a:00.0 Network controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface 11:00.0 ISDN controller: Digium,

Hi everybody, In an Asterisk 1.6.0.5, dahdi-linux-2.1.0.4, dahdi-tools-2.1.0.2, with a Digium B410P and an OpenVox A400E, I can't make "dahdi_scan" to recognize the OpenVox. This card was working correctly but suddenly stopped working and I cannot make it work again. Both ?lspci? and ?dahdi_hardware? detect it but ?dahdi_scan? not and I cannot use it. >lsppci: *0a:00.0

Hi, I have a Junghanns QuadBri installed and seems to be detected and working correctly using the wcb4xxp driver All ports are configured as TE The problem is when I connect an ISDN line - the LED turns green and Dahdi status shows Alarm OK But when I try to make a call I get "All circuits are busy" cause 27 I have searched and web and tried numerous configs but it doesn't want to

TE410P card down. I have three (3) TE410P in one machine running asterisk with SS7. My problems started last week when one of my cards started switching to E1 every time after reboot. I set the following in dahdi.conf and that solve the problem. /etc/modprobe.d/ options wct4xxp t1e1override=0x00 Now all 4 ports on that card is down with Red Alarm. I tried rebooting the machine and

Hi, I'm having problems with a TE420P card, in which I cannot make calls using spans 2 through 4. After a couple of days of working correctly, spans 2, 3 and 4 start failing (can not make calls). The system is configured to work with SS7. After the ACM message goes out, immediately a REL message is returned. I searched for error messages in /var/log/messages and could not find a clue

Hi, I'm trying to dial from one Asterisk box to a Patton 4638 BRI gateway. I'm only getting this : [May 8 15:08:24] WARNING[16797]: app_dial.c:1547 dial_exec_full: Unable to create channel of type 'DAHDI' (cause 0 - Unknown) My setup is : Asterisk 1.6.1.18 libpri 1.4.10.2 1 Junghanns QuadBRI PCI-E express with : - driver

Hello, I'm running Asterisk@home 2.5 asterisk 1.2.4 zapatel 1.2.2 libpri 1.2.2 on a Dell Poweredge 2850 (1 CPU) with a TE210P I have 2 t1 circuits using NFAS with dchan on 24 and no backup dchan. I am able to receive inbound calls on all channels and can only make outbound calls on channels 25-48. Attempting to make an outbound call on channels 1-23 results in congestion.

Hello all. I have an NEC PBX connected via a TE210p E1 line to an asterisk 1.6 box. NEC -> E1 -> TE210P:1 -> * -> TE210P:2 -> E1 -> Telco Incomming calls from the telco to the asterisk box to the NEC work fine with indials and everything. Works sweet. Outbound from the NEC to the Asterisk box fail. Giving an long dial tone that then times out. Ie, pick up NEC handset, dial

Hi, I'm using Sangoma's wanpipe together with dahdi, all software downloaded today at most recent version. Hardware is Sangoma A104, a 4xE1 card. Installation went well. Anyway, wanrouter status shows a different result than dahdi_tool or dahdi_scan. I've just put a hardware loop on port 1. All the other ports are open. wanrouter status shows the expected result: Device name |

Hi list, I'm trying to setup an asterisk 1.8.0 with MFC/R2, but I'm having these error messages loading chan_dahdi: > module load chan_dahdi.so ERROR[9241]: chan_dahdi.c:11848 mkintf: Signalling requested on channel 1 is MFC/R2 but line is in ISDN PRI signalling ERROR[9241]: chan_dahdi.c:16180 build_channels: Unable to register channel '1-15' I got the config in

Hi, After upgrading to DAHDI 2.4.0 from Zaptel, I noticed a lot of HDLC errors on my console: [Nov 27 01:15:09] NOTICE[2743] chan_dahdi.c: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 1 [Nov 27 01:15:09] NOTICE[2743] chan_dahdi.c: PRI got event: HDLC Abort (6) on Primary D-channel of span 1 These errors prevented calls from being made and received on my PRI spans. This seems

Hello everybody, I try to install -Ubuntu 8.04 server- a B410P and a TDM2400P together with Asterisk 1.4.26-2, dahdi-linux-2.2.0.2 and dahdi-tools-2.2.0. Problem I face is the following one: CLI> module load chan_dahdi.so == Registered application 'DAHDISendKeypadFacility' == Registered application 'ZapSendKeypadFacility' == Parsing

I have setup a asterisk with freepbx, a TE122 and i have an ISDN. My problem now is that callers are experiencing echo. checked on dmesg i saw this: # dmesg -c dahdi: Disabled echo canceller NLP because of CED rx detected on channel 2 i searched google but found no soolution and i have no idea what that error means. below are other details that might be of value. # dahdi_hardware

Hi, It's the first time i try to configure an ISDN card with dahdi, so my experience is very poor (be kind ;)) My problem is with dahdi_genconf, when i start it it says: /usr/sbin/dahdi_span_assignments: Missing '/sys/bus/dahdi_devices/devices' (DAHDI driver unloaded?) Command failed (status=256): 'dahdi_span_assignments dumpconfig > /etc/dahdi/assigned-spans.conf' at

Hi I am trying to connect asterisk with a Cisco GW 2600 with E1 pri using a Digium, Inc. Wildcard TE210P dual-span T1/E1/J1 card 3.3V (rev 02), Errors: [Jan 28 17:32:33] VERBOSE[6182] logger.c: == Primary D-Channel on span 1 up [Jan 28 17:32:33] WARNING[6182] chan_dahdi.c: PRI Error on span 0: We think we're the CPE, but they think they're the CPE too. [Jan 28 17:32:34] NOTICE[6182]

I need some help getting a system running for one of my company's plants. I am running AsteriskNow 1.7 with Asterisk 1.6.2.10 and FreePBX 2.8.0.2. My D-Channel keeps bouncing. The telecom tech told me he thought that I might be using the wrong sync source, and I think I might have been, but I changed DAHDI system.conf to "span=1,1,0,ESF,B8ZS" (from