similar to: E1 Channel Numbering - Your Comments.

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hello List, since some days i run into the problem that one span on a TE407P is not comming up correctly. With intense debug on that span i get: < [ 02 01 7f ] < Unnumbered frame: < SAPI: 00 C/R: 1 EA: 0 < TEI: 000 EA: 1 < M3: 3 P/F: 1 M2: 3 11: 3 [ SABME (set asynchronous balanced mode extended) ] < 0 bytes of data

Hi- Anyone using the Junghann's quad BRI card and the Digium E100P in the same system? I'm having a configuration problem where I can configure the cards one at a time (with the appropriate drivers loaded) in a system, but when I try them both together, neither will work. They both work fine one at a time. Probably has something to do with the channel numbering. I've tried

hi, I'm trying to configure my newly acquired TE410P card to work as 4 E1 spans. This is supposed to be a drop-in replacement to the earlier E100P card. However, on loading the zaptel module it gets configured as T1 spans basically doing a 'cat' on /proc/zaptel/1 thru 4, it shows 24 channels per span. After this ztcfg fails saying 'ZT_CHANCONFIG failed for channel 97'.

Hi all I have a server that has two TE412P (T1/E1+DSP) cards installed. One of them configured as an E1 PRI connected to PSTN and another one configured as a T1 E&M connected to Avaya PBX. Each card only uses two ports, so there are 2 E1 lines and 2 T1 lines connecting to this server. The purpose of this server is as a TDM trunk gateway that gets call from E1/T1 and then forward to an IP-PBX

Hi all, i have configured incoming voip traffic as follows: [voipin] exten => _X.,1,SetCallerID(033283077734) exten => _X.,2,Dial,Zap/g4/${EXTEN} exten => _X.,3,Hangup If the call going out the pri dials with an additional '0' before the dialed number. This is for caller number AND called number. But i can't see anything that says set a '0' more in front of the

Hi all, inside my * is a E400P. The machine is a PII 400Mhz with 256MB Ram. OS is Debian woody. * is the newest cvs co. I have written a little callgen script which make outgoing calls through my *: #! /bin/sh set -e n=$1 # Nummer anz=$2 # Anzhal der Versuche anz2=$3 # Kan?le sle=$4 # Timeout bis zum n?chsten Versuch if [ -z $4 ]; then sle=0 fi s=1

Hi, I have installed an TE110P but forgot to change the jumper settings to E1. I don't have easy physical access to ther server at the moment so I wonder if it will be possible to run it without changing the jumper settings with a configuration like below or will it be impossible to use the card at all before I fix the jumper? I can't try it myself yet since the operator isn't ready

hi, i'm having problems getting asterisk spliced between an E1 PRI (german Telco Arcor) and an Ericsson Business Phone 250 digital PBX. The Asterisk Server has a TE405P with it's port 1 connected to the E1 PRI provided by our telecommunications provider Arcor and port 2 connected to the E1 PRI of our Ericsson BP250. the setup before: Arcor TelCo PRI(E1)

Hi, I've connected a TE110P from digium with a 2 E1 to a Siemens PBX using asterisk from ubuntu linux. Everything is working as expected. This box is being used as a H323 gateway to the pstn. There are few complains but it is working pretty well overall. There is one thing that is bothering me. Asterisk says: May 22 05:03:39 WARNING[9360]: PRI: !! No channel map, no channel, and no ds1?

I have a 'CONGESTION' Status with R2 protocol. While testing this scenario sip GW--?Asterisk ?Digium E1 R2 Protocol?Cisco E1 R2 protocol?sip Gw Find below my error and configuration ,where are the errors in my configuration ? ========================================================================= Connected to Asterisk SVN-branch-1.6.2-r235775 currently running on

We're rolling out Cisco 7940 phones, linked to *, which is running a TE405p EuroISDN. We have 2 ISDN lines, one we had for testing, and one for general (40+ users) use. During the testing phase, we had 10 phones linked to the second ISDN line, and there were no problems with echo at all. Lucky me. However, since we have started rolling out, we've had quite loud complaints that there is

Hi, I am new with asterisk. I am setting a Wildcard TE405P. E1s in Italy come in on a pair of RG-59 coax cables with BNC connectors. So I need an adapter/balun http://www.allcomtlc.com/al_g703n3.htm . I have It but I am not sure that It works. I have configured my asterisk in this way: zaptel.conf span=1,1,0,ccs,hdb3,crc4 dchan=16 bchan=1-15,17-31 loadzone=it defaultzone=it zapata.conf

About every hour I see the yellow alarms on all or a number of channels of my PRI which is connected to the dutch telephony network, Asterisk keeps on working fine.... Here's an example where channel 1-24 went into alarm: WARNING[90124]: File chan_zap.c, Line 4139 (handle_init_event): Detected alarm on channel 1: Yellow Alarm WARNING[90124]: File chan_zap.c, Line 4139 (handle_init_event):

We have a te410p, with the following connections: span 1 connected to a 32 Channel EuroISDN span 2 connected to a card in a legacy pbx (Meridian) span 3 connected to a 10 Channel EuroISDN span 4 connected to a card in a legacy pbx (Meridian) We have no need for the meridian now, and decided to turn it off. I did not change the zaptel.conf settings, nor the zapata.conf settings. When the

Hi, I am trying to validate a setup with a sangoma A116 card (16PRI in one card). I currently have two machines set up, each with a sangoma A116 card. Those are interconnected with crossed PRI cables. One of them is in NT mode, the other in TE. The ports are configured in E1 mode, asterisk is all set up and I can make calls between them, filling up all 480 (16 * 30) channels. Now, I learned

Hello Im from Denmark and i've just got my Digium TE405P. But i have some problems when i connect it to my E1 connection (ISDN30). My telco delivered a alcatel box witch have a G.703 120ohm (DB9 with a serial to rj45) and a 75ohm coax connection. I've tried to connect using the 120ohm with rj45 and a ordinary utp cable. But it dosent seem to work. I've tried several zaptel.conf

Hi, This error I got it just when I gonfigure zaptel support isdneuro 31 channels. But if I configure zaptel to support T1 and just 24 channels I have no problem. ######################################################################## #### # # Zaptel Configuration File # # This file is parsed by the Zaptel Configurator, ztcfg # # loadzone = it span=1,1,0,ccs,hdb3,crc4 bchan=1-23 dchan=16

Hi All, I have configure my Asterisk as follow (using Asterisk@home): [zaptel.conf] span=1,1,0,ccs,hdb3,yellow bchan=1-15,17-31 dchan=16 loadzone = uk defaultzone=uk [zapata.conf] [channels] switchtype=euroisdn pridialplan=local prilocaldialplan=local internationalprefix=00 nationalprefix=0 usecallingpres=yes busydetect=no ; not need on pri callprogress=no ; was yes but wiki says experimatley

Hi, I wonder if anyone is using Digium's TE110P card on an E1 connection. I have been try to, but so far it wasn't much of a success. It only works more or less in EuroISDN as PRI CPE. And even that config gives me some trouble with channel negotiation. My current config: *zaptel.conf:* span=1,1,0,ccs,hdb3 bchan=1-15,17-31 dchan=16 loadzone=be defaultzone=be *zapata.conf:* [trunkgroups]

As these problems are very time sensitive and frustrating, I suggest you document each change you make and do them one at a time so you can actually know what the problem was and not introduce new problems in the process. Find someone who is on the phone quite a bit and will give you an honest evaluation of the call dropping situation (unless you yourself are experiencing this issue too).