Displaying 20 results from an estimated 7000 matches similar to: "AsteriskGui 2.0.4 and TDM400P"
2009 Apr 11
1
asterisknow 1.5 with X100P and TDM400P
Hi All,
Sorry if this has been around a millions times.. I have been off this
list for a few months now..
I have installed the latest asterisknow (upgraded asterisk to 1.6 as
well) and I am having a hard time getting my X100P and TDM400P working..
Its all new to me with dahdi because my old server is still running
Asterisk 1.0.2 so there have been lost of changes..
Can someone point me in
2009 Jul 03
0
DAHDI CDR problem
Hello gang,
We just got MaBell to turn on our callerid. I tested the
capability with a southwest bell box and a plain phone, so I know the line
is sending the signal. I'm running Asterisk SVN-branch-1.4-r204834 using a
TDM400P card. Here is my dahdi_cfg -vv output:
dahdi_cfg -vv
DAHDI Tools Version - 2.1.0.2
DAHDI Version: 2.1.0.3
Echo Canceller(s): MG2
2009 Mar 15
1
No hardware timing source found in /proc/dahdi
Hello all,
Ok it is Sunday afternoon and I am going crazy. I have been running in
circles so long that I can't think straight. As an example, I sent this
message to the wrong address the first try, AAARRRRGGGGGGHHHHH. I have
Asterisk 1.6.0.6 and DAHDI Tools Version - 2.1.0.2,
DAHDI Version: 2.1.0.4, OpenSuSE 10.3 x86_64, tdm422
at the end of installing dahdi-linux and dahdi-tools I get:
2005 Jun 22
4
TDM400P DevKit Problem
I installed the TDM400P and installed it on a system running on Fedora
Core1, please refer to the steps below. I connected an analogue phone to the
FXS port.
When I pick up the speaker I don't hear the dialtone although when I press a
number key I hear a DTMF generated. What could be the problem?
I appreciate your help
1- First I installed the TDM400P in the PCI slot and connected
2009 Sep 27
2
DAHDI congestion problem
I am unable to dial out over a Wildcard TDM400P. This was working previously, so must have
messed up the config somehow. I'm running Asterisk 1.6.0.15, with FreePBX 2.5.2.2.
When I dial, I see:
-- Executing [s at macro-dialout-trunk:19] Dial("DAHDI/1-1", "DAHDI/g0/9239220,300,") in
new stack
== Everyone is busy/congested at this time (1:0/1/0)
It looks like the
2007 Jan 15
1
TDM400P, fxotune and ADSL filters - Just a FYI, FWIW
This may be commonly known but I haven't come across it so here goes,
maybe it'll help someone:
I have terrible echo with asterisk 1.2, zaptel 1.2.12, and a TDM400P
with 1 FXS and two FXO modules.
The Mark2 echo canceller with Aggressive turned on was the only setting
that would make it acceptable.
I found fxotune with this zaptel version to be broken.
I pulled the latest fxotune.c
2006 Jun 14
0
FW: Issue in configuring TDM400P
Hi,
I have installed a TDM400P in a PC which runs RedHat Linux 3.2.2-5.
There is an FXS module connected to the first slot of TDM400P and an FXO
module connected to the fourth slot.
This card is detected by the operationg system, which I was able to make
sure using the output of lspci command.
I modified the configuration files zaptel.conf, zapata.conf and
extensions.conf.
When I execute the
2009 Mar 10
3
configuring channels for dahdi
after installing asterisk 1.4.23.1 and dahdi-linux-2.1.0.4 and at CLI> module load chan_dahdi.so receive the following:
signalling must be specified before any channels are.
CLI> Warning [4663]: chan_dahdi.c:11627 process_dahdi: Ignoring signalling
Error[4663]: chan_dahdi.c:10946 build_channels: Unable to reconfigure channel '1'
Error[4663]:
2010 Nov 16
1
S110M not working
Hi All -
I pulled from a working system a TDM400 with one s110 fxs and three
x100 fxos. I put it into a new box and the fxs no longer works. The
fxos work just fine. I thought it was odd, but I chalked it up to a
random chance failure and ordered another s110. The replacement
doesn't work either, and now I'm confused.
dahdi_scan recognizes the s110, but it says it fails. Output
2009 Nov 07
0
[DAHDI 2.2.0.2] "failed on channel 1: No such device or address"
Hello
No matter if I use the entry-level OpenVox A400 with a single FXO
module or the most-often-garbage card from ww.x100p.com, I get the
following error after just adding this card to Mini-ITX with a single
PCI slot (OS = CentOS 5.4):
============
# lspci -v
03:00.0 Communication controller: Tiger Jet Network Inc. Tiger3XX
Modem/ISDN interface
Subsystem: Unknown device b100:0003
2009 Aug 19
0
AsteriskGUI Create VoiceMenu SNAFU
Hi All,
I'm new to Asterisk, but am a relatively accomplished Linux guy
(RH5.1) .. I'm using the Asterisk-GUI to try and create a menu for
incoming calls on an Analog Trunk. I have recorded some .WAV files for
the menu, but when I try to upload the files, I get an AG101 message. So
I copied the files to /var/lib/asterisk/sounds/record .. when I go to
the Voice Menu Prompts
2008 Sep 05
1
dahdi & tdm400p: no luck
As best i could figure it out, I've installed dahdi and rc4.
My TDM400P doesn't answer fxo or fxs.
/etc/dahdi/system.conf:
loadzone = us
defaultzone=us
fxoks=1,2
fxsks=4
/etc/asterisk/chan_dahdi.conf:
[house-phones]
context=internal ; Uses the [internal] context in extensions.conf
signalling=fxo_ks ; fxo_ks Use FXO signalling for an FXS chanel
dahdichan => 1 ;
2005 Jan 24
0
Asterisk@Home 0.3 and the Wildcard TDM400P
Hi all,
I have been experimenting with getting the Asterisk@Home 0.3.iso to see
the Wildcard TDM400P card.
I can see card being probed in the start up, but fails (most likely due to
my having the FXO/FXS mods in the wrong place), when I try to modprob the
card it flunks, but ztcfg -vv see's the card, but complains about the
signaling being set wrong, again FXO/FXS mods may be out of
2010 Sep 01
2
Freepbx + Asterisk problem - NEED HELP
Hello,
After installing on Ubuntu 10.04 using the tutorial on
http://hmontoliu.blogspot.com/2010/03/installing-asterisk-and-freepbx-on.html
I have a running instance of Asterisk.
PROBLEM: result of dahdi_cfg:
DAHDI Tools Version - 2.2.1
DAHDI Version: 2.2.1
Echo Canceller(s): MG2
Configuration
======================
Channel map:
Channel 01: FXS Kewlstart (Default) (Echo Canceler: mg2)
2009 May 20
1
Channels configuration with DAHDI
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1
Hi all!
Days ago I bought a OpenVox A400P card with a port FXS and another FXO
that I am testing with my Asterisk installation in my house. I'm using
Asterisk 1.4.24.1 with DAHDI Linux 2.1.0.4 and DAHDI Tools 2.1.0.2 on
Debian GNU/Linux Lenny.
I was reading "The future of telephony" and this [1] document looking
for information about
2011 Jun 01
1
Dahdi_genconfig - "Empty configuration -- no spans"
Asterisk - 1.8.4.1
Dahdi-linux - 2.4.1.2
Dahdi-tools - 2.4.1
Kernel: 2.6.37.6
Kernel BKL: enabled
I am upgrading Asterisk on this box. It has an OpenVox A400P PCI analog
card with 1 FXO and 1FXS module.
This server has been running just fine for two years with Asterisk 1.6.1.0
I've just upgraded all the OS and installed Asterisk 1.8.4.1. On trying
to configure the A400P I get:
# modprobe
2009 Dec 24
0
X100P clone card problem
Hi,
I have problem with X100P clone card.I can not force it to work
under Asterisk 1.4.27.1 and DAHDI Version: 2.2.0.2.
I looked over and over on configuration and could not see any mistakes.
Here are relevant configuration files.
/etc/dahdi/system.conf
> fxsks=1
> echocanceller=mg2,1
> loadzone = hu
> defaultzone = hu
>
dahdi_tool
> OK Wildcard X100P
2011 Nov 02
2
FFA - Asterisk 1.6.2.6
Hi,
I have a 1.6.2.6 fax installation with a FFA license which seems to be
installed correctly (in fax show stats, I see that I have 1 Digium
G.711 licensed channel, and 1 Digium T.38 licensed channel).
When trying to call my business line with a fax machine, it looks like
it's ringing to my asterisk box, then transfer the call to my extension.
In the logs, I see (after the line where
2007 Apr 30
1
TDM400P and Junghanns QuadBRI issue
Hi List,
I'm setting up a system with one TDM400P (2*FXO + 2 * FXS) and one Junghanns QuadBRI
on a Fedora Core 6 (Kernel 2.6.20-1.2944.fc6).
I'm using the bristuff-0.3.0-PRE-1y-e kit. It download zaptel-1.2.16, libpri-1.2.4
and asterisk-1.2.17
When it's the time for ztcfg to do its job it complains with
<ZT_SPANCONFIG failed on span 2: No such device or address (6)>
2010 May 23
2
Dahdi problems with kernel 2.6.32
Hi. I am having problems with dahdi using kernel 2.6.32. I am using
2.6.30 kernel and it works fine -- here is the output of dahdi_cfg -vv
++ dahdi_cfg -vv
DAHDI Tools Version - SVN-trunk-r8670
DAHDI Version: SVN-trunk-r7445M
Echo Canceller(s):
Configuration
======================
Channel map:
Channel 01: FXO Kewlstart (Default) (Echo Canceler: mg2) (Slaves: 01)
Channel 04: FXS Kewlstart