similar to: bad(?) TDM400 card?

I previously posted about this problem and received suggestions involving turning off echo cancellation. As far as I can tell, echo cancellation is already disabled on this channel, so I'm back. What I've got is a small home setup with a single four-port Digium card: Module 0: Installed -- AUTO FXS/DPO Module 1: Installed -- AUTO FXS/DPO Module 2: Installed -- AUTO FXS/DPO Module 3:

I have fixed this before, but I cannot for the life of me remember how I did it. I have a TDM400P with one fxo module and one fxs module. I setup Asterisk @Home and everything works fine, except when I try and call out. If I call out with a SIP phone it calls the zap extension and not the pstn line? If I take the zap extension offhook and call with the SIP phone it dials out the pstn line

I'm getting this error on starting: WARNING[14605]: chan_zap.c:1113 zt_open: Unable to specify channel 1: No such device or address [Feb 18 18:19:44] ERROR[14605]: chan_zap.c:8074 mkintf: Unable to open channel 1: No such device or address here = 0, tmp->channel = 1, channel = 1 [Feb 18 18:19:44] ERROR[14605]: chan_zap.c:13047 build_channels: Unable to register channel '1' This

I excitedly installed my TDM dev kit earlier this weekend, installing asterisk and all the kernel drivers to make it work. And it did, it was fantastic. I then reboot the machine, and even after doing a modprobe wctdm, I get the following: == Parsing '/etc/asterisk/zapata.conf': Found Jan 31 13:34:27 WARNING[342]: chan_zap.c:793 zt_open: Unable to specify channel 1: No such device or

Hi, Some weird problem (or I'm too sleepy) happens with a tdm04B revision G (4fxo) Steps: modprobe zaptel modprobe wctdm ztcfg -vv /etc/zaptel.conf fxsls=1-4 # TDM04B defaultzone=us loadzone=us /etc/asterisk/zapata.conf signalling=fxs_ls group=1 context=incoming channel => 1-4 modprobe zaptel and wctdm load fine, however ztcfg -vv shows: 0 channels configured Im using centos 4.4 with

Hello everyone, I have a Atcom AX-1600P(1) card with a FXO module and I can't configure it. I have four extension with this PJSIP settings: --- /etc/asterisk/pjsip.conf --- [transport-udp] type=transport protocol=udp bind=0.0.0.0 [6001] type=endpoint transport=transport-udp context=from-internal disallow=all allow=ulaw auth=6001 aors=6001 direct_media=no rtp_symmetric=yes force_rport=yes

Hello, I have the following configuration : E100P -> * -> TDM400 -> Modem When I receive FAXes, about 20% of them are corrupted : pages are not always complete. If the fax is complex or with numerous pages, it's usually a mess. Before that, I was using spandsp with success. Unfortunately it's too picky with some broken fax (training failed). Since this failure only occurs with

I installed Trixbox and a TDM400P with 2 FXO and 2 FXS ports and am having an annoying issue with the FXO ports. As soon as I plug either one into the phone line it's as though the line is disconnected i.e. get disconnected tone when trying to dial out, line is busy when dialling in. The CLI shows the following: trixbox1*CLI> zap show channel 4 Channel: 4 File Descriptor: 18 Span: 11*

The Asterisk Development Team is pleased to announce the release of DAHDI-Linux 2.5.0.1 and DAHDI-Tools 2.5.0.1. 2.5.0.1 is a bug fix release. It is recommended that current users of v2.5.0 upgrade. DAHDI-Linux 2.5.0.1, DAHDI-Tools 2.5.0.1, and DAHDI-Linux-Complete 2.5.0.1+2.5.0.1 are available for immediate download at: http://downloads.asterisk.org/pub/telephony/dahdi-linux

The Asterisk Development Team is pleased to announce the release of DAHDI-Linux 2.5.0.1 and DAHDI-Tools 2.5.0.1. 2.5.0.1 is a bug fix release. It is recommended that current users of v2.5.0 upgrade. DAHDI-Linux 2.5.0.1, DAHDI-Tools 2.5.0.1, and DAHDI-Linux-Complete 2.5.0.1+2.5.0.1 are available for immediate download at: http://downloads.asterisk.org/pub/telephony/dahdi-linux

Has anyone had success with the TDM400 in production? I have multiple boxes where these cards lock up and the only thing that will fix them is to unload *, modprobe -r wctdm, modprobe wctdm, load asterisk. Does not matter if it is a FXS/FXO module. I know this topic has been discussed many times before, but my questions is not "is anyone else having this problem" since I know that

hi you, I'm having problem with voice quality on my trixbox using TDM2400B.The trixbox is connected via 20 FXO ports on a TDM2400 with the hardware echo cancel module. Echo cancel almost works, but the users hear what they describe as a 'background crackle/buzz' coming back when they talk. anyone have the same problem? pls help me. thanks a lot. my trixbox and config

Hello, After installing on Ubuntu 10.04 using the tutorial on http://hmontoliu.blogspot.com/2010/03/installing-asterisk-and-freepbx-on.html I have a running instance of Asterisk. PROBLEM: result of dahdi_cfg: DAHDI Tools Version - 2.2.1 DAHDI Version: 2.2.1 Echo Canceller(s): MG2 Configuration ====================== Channel map: Channel 01: FXS Kewlstart (Default) (Echo Canceler: mg2)

Folks, I have a Xen Asterisk VM with a TDM400 card. When I try to run dahdi_cfg, I get: tempest:~# dahdi_cfg -vvv DAHDI Tools Version - 2.2.0 DAHDI Version: 2.2.0 Echo Canceller(s): Configuration ====================== Channel map: Channel 01: FXO Kewlstart (Default) (Echo Canceler: none) (Slaves: 01) Channel 03: FXS Kewlstart (Default) (Echo Canceler: none) (Slaves: 03) Channel 04: FXS

I go to my Zaptel 1.4.0 folder and run ./configure; make linux26; make install and I don't see any errors. This is out of my modprobe.conf: install tor2 /sbin/modprobe --ignore-install tor2 && /sbin/ztcfg install torisa /sbin/modprobe --ignore-install torisa && /sbin/ztcfg install wcusb /sbin/modprobe --ignore-install wcusb && /sbin/ztcfg install wcfxo

I have a AEX800 PCI Express card - sort of a TDM800 with PCI-Express. (or AEX844 - 4FXS & 4FXO) I downloaded Asterisk Now - and have got this loaded on a new motherboard (Intel with 3 PCI, 3 PCI Express - etc). (Downside on PCI-Express is the physical support the express slot gives (very little) compared with an 'old' standard PCI slot!!!) With only this card in the box....

Hi, Before I report a bug on http://bugs.digium.com, I would like to know if someone is seeing the same error message. Personally I am not using wctdm24xxp but other modules such as wcte12xp and wctdm. The latter modules load fine and are compiled with pci_register_driver as expected. The only module that seems to require the deprecated function pci_module_init is wctdm24xxp. Is this normal?

Hi all, I have hit a wall configuring a TDM400, I have set these up before without issue but today I just can't seem to figure out what I am doing wrong. On an incoming call the following is produced in the Asterisk console with verbose 4 -- Starting simple switch on 'Zap/2-1' Mar 22 16:12:34 NOTICE[2051]: chan_zap.c:6063 ss_thread: Got event 18 (Ring Begin)... Mar 22

Running Asterisk 1.6.2.9, DAHDI 2.3.0.1, CentOS 5.5 (update to date as of a week ago), I've installed a Digium AEX800P with 2 X400M FXO Modules and 1 VPMADT032 Module, hooked up to 5 analog lines. I get the error message referenced in the subject in my dmesg output everytime I load / reload DAHDI using the command "system dahdi start/restart". When I make an outbound call over

Hello group, I am installing Asterisk on a new pc running Ubuntu 12.04.3 Server. ?I have dahdi-complete-2.7.0.1+2.7.0.1, and have tried 2.6.1 and 2.8.0-rc1 and 2.8.0-rc2. ?I am following along in the ASTERISK The Definitive Guide 4th Edition and on page 116 when I issue the command $ sudo /etc/init.d/dahdi start I get the following error: Loading DAHDI hardware modules: ? ?wctdm24xxp: done