Displaying 20 results from an estimated 1000 matches similar to: "odd T1 issue"
2010 Dec 15
2
Echo Cancellation Problem - Invalid Argument?!?
Greetings folks-
I'm experiencing issues with a freshly installed box. When a call comes in via PRI (Sangoma AFT-A104), I see this in my logs:
[Dec 15 14:26:10] WARNING[23546] chan_dahdi.c: Unable to enable echo cancellation on channel 12 (Invalid argument)
[Dec 15 14:26:10] WARNING[23546] chan_dahdi.c: Unable to enable echo cancellation on channel 8 (Invalid argument)
[Dec 15 14:26:10]
2006 Jun 17
0
T1 + E&M
Maybe of you guys know the answer to this:
We have T1's that come from both MCI and Global Crossing as channelized (24
Ports per T) with inband (DTMF) delivery
of ANI and DNIS (format = *DNIS*ANI*). My old equipment was set for D4,
AMI, SF and Wink Start and so is Asterisk. I've moved these T's to Asterisk
TE410P and inbound calls are arriving to external voice mail system
2010 Apr 01
2
Problem with Sangoma A104 and euroisdn pri
Hi all,
My problem boils down to these errors:
... Unable to create channel of type 'ZAP' (cause 34 -
Circuit/channel congestion)
== Everyone is busy/congested at this time
This is triggered by lines in extentions.conf such as:
exten => _X.,1,Dial(ZAP/g1/${EXTEN},,W)
The system is CentOS v5.2 with Asterisk 1.4.23
(druid-asterisk-1.4.23.1-2), a Sangoma A104
2005 Feb 17
2
Sangoma A104 - D-Channel problem
Hello,
I have following problem with Sangoma A104 card:
CLI> pri show span 1
Primary D-channel: 16
Status: Provisioned, Down, Active
Switchtype: EuroISDN
Type: CPE
Window Length: 0/7
Sentrej: 0
SolicitFbit: 0
Retrans: 0
Busy: 0
Overlap Dial: 0
T200 Timer: 1000
T203 Timer: 10000
T305 Timer: 30000
T308 Timer: 4000
T313 Timer: 4000
N200 Counter: 3
NOTICE[16509]: chan_zap.c:7494 pri_dchannel: PRI
2009 Dec 03
2
dahdi_tool shows no alarms, but no line connected
Hi,
I'm using Sangoma's wanpipe together with dahdi, all
software downloaded today at most recent version.
Hardware is Sangoma A104, a 4xE1 card.
Installation went well.
Anyway, wanrouter status shows a different result than
dahdi_tool or dahdi_scan.
I've just put a hardware loop on port 1. All the other
ports are open.
wanrouter status shows the expected result:
Device name |
2008 Oct 06
2
Conneting Asterisk to Swyx pri
Hi all, I've done this a few times with other PBX's but swyx has stumped me!
I'm having some trouble getting Asterisk connected to a Swyx system using a
sangoma A104dx... currently the setup is:
BT <-> Swyx
The above setup works fine... what i'm trying to achieve is
BT & SIP Trunks <-> Asterisk <-> Swyx
I have connected to our BT (2 x ISDN30 UK) with
2006 Jun 17
0
E&M + Dial tone
Maybe of you guys know the answer to this:
We have T1's that come from both MCI and Global Crossing as channelized (24
Ports per T) with inband (DTMF) delivery
of ANI and DNIS (format = *DNIS*ANI*). My old equipment was set for D4,
AMI, SF and Wink Start and so is Asterisk. I've moved these T's to Asterisk
TE410P and inbound calls are arriving to external voice mail system
correctly
2007 Jan 24
1
Getting confused on signalling mode Vs framing and encoding: T1 CAS
Hello,
I'm trying to make my asterisk box to act as a telco, in order to reproduce a US environment in europe.
Our telco provider is giving us those settings:
ESF
B8ZF
Inbound = E&M Immediate
Outbound sig =Wink Start
Yield to Glare = Yes
Those trunks are using CAS for signaling.
I have tried many configs/combinations in zaptel.conf and zapata-channels.conf
In zaptel.conf, when having
2011 Mar 23
1
Sangoma A102D wanpiple issue with dahdi
Hey Guy,
I have ubuntu 10.04 64bit and compiled dahdi / wanpipe 3.5.19 /asterisk-1.8.x I didn't understand what is the relation between wanpipe and dahdi ? do i need to start wanrouter service ? I am getting weird errors and my system got kernel panic many time when i restart dahdi service. any idea ? what is the startup sequence of all these service ?
root at example:/etc/asterisk#
2011 Feb 11
2
sangoma wanpipe install error
Trying to install wanpipe 3.5.18.
No errors during compile. But when I reach the point where wanpipe and
dahdi_cfg is started, I encountered an error.
Starting WAN Router...
Loading WAN drivers: wanpipe done.
Starting up device: wanpipe1
wanconfig: WAN device wanpipe1 driver load failed !!
: ioctl(wanpipe1,ROUTER_SETUP) failed:
: 22 - Invalid
2011 Feb 17
0
PRI "wanrouter status" shows disconnected - system problem or Telco?
Hi everyone,
I am reading through Sangoma Wiki right now. But someone may already and
quickly notice this. I have a system that is down since the morning (maybe
power intruptions). All seems fine except for "wanrouter status" shows
disconnected. Following are the alarms raised. Should I call telco (they
have long wait times) or should I just keep searching online for
troubleshooting
2013 Apr 30
2
Asterisk QSIG doesnt send the calling name to Nortel CS1000
Hello to all,
I have a problem with an asterisk qsig.
I have three machines:
Nortel CS1000 --- Card Sangoma PRI ---> Asterisk QSIG ---SIP Trunk--->
Asterisk
I use Snom phones on Asterisk.
If I call from Asterisk to Nortel, Nortel reminds me of the name of the person
i'm calling and I visualize on the display of Snom phone, but if I call from
Nortel to Asterisk, the QSIG does not send
2007 Nov 01
1
Connection astrisk to a RAS (portmaster)
Here's my planed setup :
PRI from telco <--> (port 1 of A104d) * (port 2 of A104d) <--> PM3
The PM3, for those who don't know is lucent's portmaster RAS dial-up router.
I had setup asterisk, zaptel, libpri, wanpipe (as I have sangoma's cards).
In wancfg, I have port 1 as TDM_VOICE, with hardware echo on, span 1. Port 2
is TDM_VOICE, without hw echo, Clock as
2014 Aug 01
1
load testing and pattern testing sangoma A116 card
Hi,
I am trying to validate a setup with a sangoma A116 card (16PRI in one
card). I currently have two machines set up, each with a sangoma A116
card. Those are interconnected with crossed PRI cables. One of them is
in NT mode, the other in TE.
The ports are configured in E1 mode, asterisk is all set up and I can
make calls between them, filling up all 480 (16 * 30) channels.
Now, I learned
2009 Oct 23
1
Strange IAX2 / Iaxmodem problem
Hello.
I'm having a strange problem with the IAX2 channel and IAXmodem and I was hoping to get some light from someone in these lists.
On my logs and on the console I'm getting a bunch of lines with:
[Oct 23 14:26:18] NOTICE[4417] chan_iax2.c: Peer 'XXX' is now UNREACHABLE! Time: 3
[Oct 23 14:26:28] NOTICE[4413] chan_iax2.c: Peer 'XXX' is now REACHABLE!
2007 Dec 02
1
setting up two asterisk server as ss7 back to back.
I have used asterisk-1.4.14, zaptel-1.4.7, chan_ss7-1.0.0 on FC7 all
went okay. using sangoma a104dx on both machine.
I followed the write up on
http://www.voip-info.org/wiki/index.php?page=Asterisk+ss7+setup
I have the cross over cable between them.
however, wanpipe shows connected but the signaling link does not align.
i have my configs for host A
##wanpipe1.conf
[devices]
wanpipe1 =
2005 May 06
0
My Sangoma Experience in Asterisk: Followup
My Sangoma Experience in Asterisk: Followup
2005-05-06
original review can be found at:
http://astguiclient.sourceforge.net/Sangoma_experience.txt
It's now been a month since I finished my last round of tests with the
Sangoma A104u board in Asterisk. I have had a lot of conversations with the
guys at Sangoma about how my system runs so that they could set up their
test systems to try to
2007 Jul 03
1
Distinctive ring detection not detecting ring cadences
I'm using Asterisk 1.4.5 (will try 1.4.6 on Thursday, but I don't see
anything in the changelog after the 1.4.5 release dealing with
distinctive ring), zaptel 1.4.3, and wanpipe 2.3.4-10 with a Sangoma
A200 card. I enabled usedistinctiveringdetection in zapata.conf.
However, on the Asterisk console, the output I get is:
-- Detected ring pattern: 0,0,0
It would appear that Asterisk is
2009 Oct 02
1
One side SIP goes dead on length conversation
Has anyone seen something like this before. Randomly, on longish calls, the
local side of the call audio goes dead. Meaning remote caller can hear us
but we cannot hear the remote person?
Linux voip 2.6.18-128.1.6.el5 #1 SMP Wed Apr 1 09:10:25 EDT 2009 x86_64
x86_64 x86_64 GNU/Linux
Asterisk 1.4.24.1, Copyright (C) 1999 - 2008 Digium, Inc. and others.
WANPIPE Release: 3.4.1
Wanpipe Config:
2010 Jul 29
1
Problem with Sangoma card...
I have a problem with a Sangoma card. It worked until yesterday. Now
I keep getting this error:
Jul 29 17:45:17 pbxacura kernel: wanpipe1: Enable E1 CAS signalling
mode!
Jul 29 17:45:17 pbxacura kernel: wanpipe1:w1g1: Rx Error: No
'DeviceSelect' from target: pci fatal error! (0x000FA000)
Jul 29 17:45:48 pbxacura last message repeated 30946 times
It is using Wanpipe 3.5.6 and Zaptel