similar to: US Caller ID

Hello, All :) Regarding to incoming caller ID on PSTN line, which one is best supported by asterisk: is it FSK ETSI or FSK US? I bought some caller ID converter hardware (convert DTMF to FSK and vice versa) but still asterisk can not detect it. The converter has a switch FSK ETSI or FSK US This is what I put in /etc/asterisk/chan_dahdi.conf ... cidsignalling=bell cidstart=ring ... If after

I'm not 'overly' new to asterisk, but I am very new to the Digium card / Telco aspect of it. I was able to get a TE110p card, installed.. and hooked a t1 up to it. I'm using zttool to just look at 'some' output. Here is what it looks like when I just load it up: Current Alarms: No alarms. ? ? ? ? Sync Source:

In my * server I have a T100P, connected with a T1 crossover cable to an Adtran TA750 with 2 FXO cards. After I do 'modprobe wct1xxp;ztcfg' the alarm on the card starts blinking red. Running zttool confirmed that yes, it is a red alarm. I've read a few previous posts on this type of setup and I'm not too much closer. What should I be checking next? A different cable? The

I have what my SBC/ATT representative calls a "Supertrunk," but he can't tell me the specifics I need to know to configure Asterisk to work with it. By fiddling about, I've come up with the "almost working" configuration below. This works except that it takes about 4 seconds from when the console says the line is answered until it plays my prompt. Watching the

Hi, I use asterisk branch 1.4 and gui 1.4 as well. I have the following situation: When I try to make gui configuration by http://localhost:8088/asterisk/static/config/setup/install.html I can see that application logs my user correctly but there is no browser window shift to the next page. it stays at the logging one. I get the following info in the console: [Feb 4 09:33:09] == Parsing

Hello, I have an E100P, and in the zaptel.conf I have: span=1,1,0,ccs,hdb4,crc4,yellow fxsks=1-10 the light on the card is green( BTW what do all those states of the card that zttool reports YELLO, RED, BLUE ..., is there a doc for zttool?, or for the card?) in the asterisks` zapata.conf I have: [channels] context=default switchtype=euroisdn signalling=fxs_ks usecallerid=yes hidecallerid=no

Good morning, I have a digium wctdm24xxp in my asterisk box, i am not able to see the callerid when the call is incoming from the fxo line, i live in Brazil, how can i change the signaling from fsk to dtmf? Thanks. -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi, Using 1.4.26.1 & DAHDI 2.2.0.2, FSK VMWI devices off a TDM840 work fine. With 1.6.1.[45] & same DAHDI, instead of the FSK spill I get a line polarity reversal. Stutter dialtone is generated as expected. Has anyone else seen this? Is there anything special I need to do for 1.6.1 to make FSK MWI work? Thanks, --Barry

The TDM410P doesn't support 'hvac', only the obsolete TDM400P supports that option was for the old phones that have a neon light (or equivalent LED+ZENER ciruit). Are other phones off the TDM410P (other than the VTECH) working, or is the Vtech the only model with VMWI available to you. I'm not able to check at the moment, I have copied the asterisk-users list, someone else may

> I've never bothered to check to see if cat5 cables use the appropriate > mating twisted pairs or not. Since the pinouts are different for cat5 vs > T1 cables, I'd have to guess a single strand is used from two different > twisted pair groups. That wouldn't be cool, but in short runs it > probably doesn't have much of an impact. > IIRC, standard Ethernet uses

Hi, Is it possible to monitor conversation of logged in Agents? Currently I am using ZapScan to monitor incoming calls, but I would like to monitor individual agents. raj

Anyone successfully implemented a solution for allowing ZapBarge call monitoring only for a specific group of agents calls? The issue I see is that the feature only works on zap channels, and all of the agents (in many cases) are IP phones. Allowing ZapBarge and ZapScan on the TDM PSTN (t100p) interface has privacy issues for senior managers, but would allow all outbound zap calls to be

I'm trying to get a Carrier Access Corp. Channel Bank I working with a Digium T100P without success. What is stranger is that the status lights on the channel bank and T100P seem to change almost each time I power cycle the channel bank or reset the T100P. The channel bank has three status lights: T1, Framing, Status. T1 is green, Status is yellow, and Framing is usually red but sometime

I have a Samba-LDAP PDC at an office and 5 BDC's at other offices. At corporate HQ I have a W2k Server and domain. I have properly configured an interdomain trust and Users in the Samba domain can get to sections on the W2k machine regardless of location. However, members in the W2K domain can only access shares on the PDC. Attempts to access shares on a BDC cause a user name

hi, i have problem with pass-through faxing with this scenario hylafax(iaxmodem) - iax - asterisk1 1.2.22 - sip - asterisk2 1.2.X(xen virtual) - linksys ATA i can fax to fax2mail on hylafax but after upgrade asterisk2 to 1.4 faxing is not working hylafax(iaxmodem) - iax - asterisk1 1.2.22 - sip - asterisk2 1.4.X(xen virtual) - linksys ATA configuration is same do you hava any idea what is

Hi, It seems like my ATA is making a ringing noise... (as it used to), but now (After the upgrade from 1.0.7 to 1.2) asterisk also is either making the ringing, or passing the PRI ringing from the telco on to me. Any suggestions on how to fix this?

We have a Asterisk box acting as a voicemail system and greeting/ call director for our phone system (NEC system). The problem we are having is that randomly (though most especially with cell phones) asterisk thinks it is getting a double digit. For example, somebody will enter "269" and asterisk will read "2269". I believe the core problem is the NEC system's

We are using Bellsouth 8867 phones on our TDM400B FXS lines (asterisk-1.0.3). It has a "Voicemail" light, which appears to be MWI (according to the manual it works with voicemail from the telco that sends a FSK signal). The dialtone stutters when a line has voicemail, so I know that I have the mailbox setting right in zapata.conf, but the light doesn't go on. I am also getting

After purchasing the Uniden TRU9480 and then the Panansonic 5672, both of which do not have "phone company" compatible FSK/stutter MWI, I finally got smart and found out just which Panasonic phones have this feature. Only the following 5.8G models in their current line have FXO compatible MWI. I purchased the 5771 unit and one remote. I have confimed it does in fact work with Asterisk

Greetings, We are looking at installing a VoIP system with Asterisk and are currently looking at the line of 3Com phones. Has anybody had success with using the following phones? We need to buy a lot and we don't want to end up with phones that don't work properly with asterisk. 3Com 3101 (model with speakerphone) 3Com 3102 Business Phone 3Com 3103 Manager Phone 3Com 3105