similar to: zaptel-Error

Hello, I have a problem with zaptel. I hope you can help me. I installed and configure zaptel. ZAPTEL.CONF span=1,1,0,ccs,hdb3,crc4 bchan=1-15,17-31 dchan=16 loadzone = de defaultzone=de But the output of cat /proc/zaptel/* Span 1: WCT1/0 "Digium Wildcard TE110P T1/E1 Card 0" (MASTER) HDB3/CCS/CRC4 RECOVERING 1 WCT1/0/1 Clear (In use) RED

Hi guys, I've been installing and configuring a TE110p card. The compile and install went very well. I'm using this on FC4 and I compile with linux26 as well checked I on the udev configs. zttool and ztcfg both indicate that the card is ready. But when I try to "load chan_zap.so" then I get the following Unable to load module chan_zap.so Jan 5 21:43:33 ERROR[6808]:

Hello all. I have here a TE110P (configured as E1) and a TDM400P (with four X100P - FXS). Both boards are recognized by the operating system as showed above: 0000:08:00.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface Subsystem: Unknown device b1d9:0003 Flags: bus master, medium devsel, latency 64, IRQ 169 I/O ports at e800 [size=256]

hello all, i'm using TE110P and all configuration prosess is done. but after i do the 'modprobe' for zaptel and wcte11xp, follow by ztcfg -vv and asterisk -vvvgc i have this error. *CLI> May 27 14:44:33 WARNING[3059]: chan_zap.c:8534 pri_dchannel: PRI Error: We think we're the network, but they think they're the network, too. May 27 14:44:34 WARNING[3059]: chan_zap.c:8534

We have a te410p, with the following connections: span 1 connected to a 32 Channel EuroISDN span 2 connected to a card in a legacy pbx (Meridian) span 3 connected to a 10 Channel EuroISDN span 4 connected to a card in a legacy pbx (Meridian) We have no need for the meridian now, and decided to turn it off. I did not change the zaptel.conf settings, nor the zapata.conf settings. When the

Hello. I have a TE212 configured in E1 mode. This is shown in a cat /proc/zaptel/2 and 3 (where the card is configured): cat /proc/zaptel/2 Span 2: TE2/0/1 "T2XXP (PCI) Card 0 Span 1" HDB3/CCS/CRC4 RED NOTOPEN 25 TE2/0/1/1 Clear 26 TE2/0/1/2 Clear 27 TE2/0/1/3 Clear 28 TE2/0/1/4 Clear 29 TE2/0/1/5 Clear 30 TE2/0/1/6 Clear

We're rolling out Cisco 7940 phones, linked to *, which is running a TE405p EuroISDN. We have 2 ISDN lines, one we had for testing, and one for general (40+ users) use. During the testing phase, we had 10 phones linked to the second ISDN line, and there were no problems with echo at all. Lucky me. However, since we have started rolling out, we've had quite loud complaints that there is

Hi, I bought a Digium Quad E1 card model TE406P. Till now, I can't make it work... I mean, I have red alarm when I configure one E1. The provider is in France (France T?l?com) and I use the following zaptel config : span=1,1,0,ccs,hdb3,crc4 bchan=1-15,17-31 dchan=16 I'm using Linux 2.6.15 and when I run ztcfg -vvvv, it seems that all channels are configured... So can someone

Hi, I configured an asterisk box with 1 Digium Wildcard TE110P T1/E1 Card 0 I setup the jumper in e1 position. my zaptel.conf : defaultzone=it loadzone=it #gestione PRI span=1,0,0,ccs,hdb3,crc4,yellow bchan=1-15 # set this to 1-15,17-31 for E1 dchan=16 # set this to 16 for E1 bchan=17-31 # set this to 1-15,17-31 for E1 # Asterisk starts correctly, I see th 30 channels. Anyway I cannot put

Hi all, Does somebody know how I have to setup my TE405P ? Is it correct my configuration below ? Otherwise, can somebody help me ? Thanks, Angel. zaptel.conf span=1,1,0,ccs,hdb3 span=2,0,1,ccs,hdb3 span=3,0,1,ccs,hdb3 span=4,0,1,ccs,hdb3 bchan=1-15 dchan=16 bchan=17-31 bchan=1-15 dchan=16 bchan=17-31 bchan=1-15 dchan=16 bchan=17-31

Hi there, I've got two Asterisk hosted PBX servers with Digium TE210P cards attached by a E1 cable to Port 1 on each. On startup, both cards flash red, alternating between ports 1 and 2. When server #1 loads the Zaptel module and drivers, Port 1 status LED goes green. When server #2 loads the same module and drivers, Port 1 status LED goes completely blank. Unloading the wct2xxp

Hi, I wonder if anyone is using Digium's TE110P card on an E1 connection. I have been try to, but so far it wasn't much of a success. It only works more or less in EuroISDN as PRI CPE. And even that config gives me some trouble with channel negotiation. My current config: *zaptel.conf:* span=1,1,0,ccs,hdb3 bchan=1-15,17-31 dchan=16 loadzone=be defaultzone=be *zapata.conf:* [trunkgroups]

Hi, I have this error, I have a digium card TE110P Tiger3xx When I'm load the dirvers by this command modprobe wcte11xp I got this error "Notice: Configuration file is /etc/zaptel.conf line 0: Unable to open master device '/dev/zap/ctl' 1 error(s) detected FATAL: Error running install command for wct1xxp " when I'm Lunch the command ztcfg -vv I got this error.

hi, I'm trying to configure my newly acquired TE410P card to work as 4 E1 spans. This is supposed to be a drop-in replacement to the earlier E100P card. However, on loading the zaptel module it gets configured as T1 spans basically doing a 'cat' on /proc/zaptel/1 thru 4, it shows 24 channels per span. After this ztcfg fails saying 'ZT_CHANCONFIG failed for channel 97'.

Hi All, I have configure my Asterisk as follow (using Asterisk@home): [zaptel.conf] span=1,1,0,ccs,hdb3,yellow bchan=1-15,17-31 dchan=16 loadzone = uk defaultzone=uk [zapata.conf] [channels] switchtype=euroisdn pridialplan=local prilocaldialplan=local internationalprefix=00 nationalprefix=0 usecallingpres=yes busydetect=no ; not need on pri callprogress=no ; was yes but wiki says experimatley

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hello List, since some days i run into the problem that one span on a TE407P is not comming up correctly. With intense debug on that span i get: < [ 02 01 7f ] < Unnumbered frame: < SAPI: 00 C/R: 1 EA: 0 < TEI: 000 EA: 1 < M3: 3 P/F: 1 M2: 3 11: 3 [ SABME (set asynchronous balanced mode extended) ] < 0 bytes of data

Dear All, I'm integrating avaya commuication manager difinity ver 1.0 with asterisk using B2B E1. following are the details of my H/W, zaptel configs and software installed. Digium TE110p asterisk 1.2.19 cent OS 4.4 zaptel 1.2.18 libpri 1.2.4 etc/zaptel.conf span=1,0,0,cas,hdb3 bchan=1-15,17-31 dchan=16 when i ztcfg -vvv im having this error message and the E1 is not getting up. "cas

Hi, I am able to dial through asterisk PBX having TE120P card to E1 card running application. Communication was established successfully Now, I want to do the reverse way out. I am using the following configurations 1)zaptel.conf span=1,1,0,ccs,hdb3,crc4 defaultzone=us bchan=1-15,17-31 dchan=16 2)zapata.conf group=1 signalling=pri_net switchtype=euroisdn context=incoming

hello, We encountered signaling problem with a french national carrier. They ask us, which signaling is configured on our single E1. I need to know if it's ETSI, VN4 or VN6. I know what ccs, and hdb3 mean but I do not succeed to make the link between the signaling type. I searched through RFC Q.921 and Q.931 It would be great to obtain some help. cedric

hi, i'm having problems getting asterisk spliced between an E1 PRI (german Telco Arcor) and an Ericsson Business Phone 250 digital PBX. The Asterisk Server has a TE405P with it's port 1 connected to the E1 PRI provided by our telecommunications provider Arcor and port 2 connected to the E1 PRI of our Ericsson BP250. the setup before: Arcor TelCo PRI(E1)