similar to: ERROR:Failed to create H323 listener

I have checked and nothing is running on 1720, I even tried other ports Thanks ------=_Part_156950_6447813.1223890893752 Content-Type: text/html; charset=ISO-8859-1 Content-Transfer-Encoding: 7bit Content-Disposition: inline <div dir="ltr">Hi<br>I am trying to get H323 to run on Asterisk, basically I had Asterisk running so I followed this tutorial <br><a

Hi, My configuration is SipPhone<----->asterisk1 <----->asterisk2. My asterisk version is 1.2.10. I installed chan_h323 according to 'http://astrecipes.net/?n=102'. When i call from asterisk1 to asterisk2, there is no audio. Using 'rtp debug', I can see that rtp packets are being received. Regards, Jason. #------h323.conf for both------------------------ [general]

I'm trying to configure Chan_H323 to register with GnuGK... without success... i've failed finding sample configurations. I'd greatly appreciate anyone who can provide sample config of H323.conf and gnugk.ini I am tyring to configure Asterisk as a neighbor in GnuGK. I'm always getting this error on Asterisk. ERROR[16384]: chan_h323.c:1987 load_module: Gatekeeper registration

Dear friends, I have compiled and installed h.323 in my asterisk. And I have a service from a H.323 VoIP provider who give me user, password and gatekeeper IP address. All configured. But when I start my asterisk i receive the following error and h.323 calls can not be making and/or receiving. [chan_h323.so]=> (The NuFone Network's Open H.323 Channel Driver) == Parsing

Hello, I have a strange h323 issue. After executing command "Dial("SIP/333-0d1dfe00", "H323/361737052390920 at ccg|5|tT")" at Oct 18 22:32:23. Meanwile I have sniffing traffic on port 1720. The call was established just at Oct 18 22:33:03 (New H.323 Connection created.) and also packet sniffer grabs the h323 invites at this time also. So my question is what

Hi list, After several tries to understand the subtil description in the h323.conf to be able to make the next scenario I was presented the following error messages by asterisk. Can somebody tell me please what I am doing wrong. Scenario: Gatekeeper (h323) --> Asterisk PBX -->(h323) Gateway Endpoints are connected to Gatekeeper. Call does come in like 999931235650087 with codec g711

Hi all, I'm trying to trunk my asterisk with a cisco cme 3.3 using h323. Cisco conf: dial-peer voice 8 voip destination-pattern 2... session target ipv4:<asterisk ip> codec g711alaw no vad h323.conf [general] port = 1720 bindaddr = 0.0.0.0 ;tos=lowdelay ; disallow=all allow=alaw allow=ulaw allow=gsm context=from-internal extension.conf [from-internal] exten =>

Asterisk has been working fine for me for several weeks using MGCP to a Adit600 for intra office calling. I have recently loaded h323 and the following errors occurs when starting asterisk. [chan_h323.so]Aug 10 09:09:18 WARNING[7824]: loader.c:258 ast_load_resource: libpt_linux_x86_r.so.1.5.2: cannot open shared object file: No such file or directory Aug 10 09:09:18 WARNING[7824]:

[public_gk] ;exten => _070.,1,Set(CALLERID(number)=070333333${CALLERIDNUM}) exten => _070.,1,Dial(H323/${EXTEN}@59.120.139.119) exten => _070.,n,Hangup *CLI> h323 show peers Name Accountcode ip:port Formats 7000 ast_h323 203.160.252.147:1720 0x4 (ulaw) 88670333333 ast_h323 203.160.252.147:1720 0x4 (ulaw)

Hello, I'm trying to use the GSM codec with Nufone H323 but it's not working. Does somebody has some idea? Have I missed something? Thanks!! Celso Fassoni Some additional info: (I'm using CVS-HEAD - downloaded today) monkey:~# cat /etc/asterisk/h323.conf [general] port = 1720 bindaddr = 192.168.0.100 ; this SHALL contain a single, valid IP address for this machine

Hi, Someone released a succefull interconnection in H323 with WTL equipement ? I'm trying to do that with an IPNx. But get dead air. With chan_oh323 it's fine, all works. With chan_h323 => dead air. The configuration is GW to GW. This is my configuration from h323.conf: [general] port=1720 bindaddr=my.ipaddr dtmfmode=rfc2833

I am using Nu Fone Network's h323 drivers. I can place H323 calls using following in extensions.conf file, exten => _1732.,1,Dial(H323/${EXTEN}@192.168.1.2) If I need to use h323.conf to do the same I cannot configure h323 to do the same. I get everyone is busy message and I do not see IP packets being generated by * trying to communicate to 192.168.1.2. Can someone point out what I

Does asterisk support using an H.323 provider for outgoing calls? From everything I have found, it looks like it does. However, I have had no success in getting it to work. I would really appreciate if somebody could give me a hand. I am using the channel that comes with asterisk. I have also tried using the channel from inaccessnetoworks but have not had any more success. My provider

Heya, I changed the Makefile of the h323-channel-makefile (I downloaded cvs of a couple of hours ago) so that I don't have to rebuild pwlib and openh323, but can use the precompiled versions. I'm using pwlib 1.8.3 and openh323 1.15.2. There aren't many changes. I replaced OPENH323DIR with OPENH323INC ,which points to /usr/include/openh323 for me and OPENH323LIB, which points to

Hi, all! when my h323 phone dial in Asterisk system, i can hear nothing. and the following is the log slice i picked from /var/log/asterisk/full. ps: i am using red hat AS5 kernel 2.6.18-53.el5,Asterisk-1.4.24.1, pwlib_v1_11_0, openh323_v1_19_0_1. Best Regards! 81948 [May 6 10:07:34] VERBOSE[11579] logger.c: -- Remote UNIX connection 81949 [May 6 10:07:51] VERBOSE[29627] logger.c:

What is the difference between H323 and OH323 in Asterisk? I need Asterisk to have basic H.323 support so we can offer some simple H323 termination for some of our Cisco and Quintim hardware. Our upstream provider uses SIP, so I figured I'd use Asterisk as the go-between. I already setup Asterisk so it can push calls out through our providers via SIP. I just need a good/solid/very simple H323

Dear All. I have installed Asterisk-1.0.6 on FreeBSD-5.4 RELEASE via port, so the chan_h323.so modules already included. When i try the SIP channel, asterisk works fine. In this case, i use the XLite softphone as client, i can hear the voice transfered through clearly. Asterisk is good!! :D The problem is when i try the H323 channel, the voice cannot be transferred through. I have

Greetings- As most of you who monitor this list know, I've been messing about with Asterisk -HEAD, Cisco Callmanager, and the nufone H323 channel driver here for some time- with pretty decent success. I'm hoping to cash in a chip here- I've run into something that is probably a very simple answer, yet not found a decent reference to resolve it. Scenario- -HEAD as of last week

Hi Users, Administrators and Pavel Jezek, You prefer chan_h323 from asterisk tree and it's of course that use channels by tree is very good. But in 1.2.x, the chan_h323 is very simple and the chan_oh323 is so bad. And I work with chan_ooh323, that it's too from Digium and work good! And I am Studing one possible change to Asterisk 1.4.x , but in 1.4.x the oh323 channel don't have more,

Hello, I installed Asterisk from CVS on Redhat Linux 9 and working with chan_h323 module and g729/g723 free codecs too. My network connection diagram: ---------------------------------------------- X-lite/X-Pro-->Asterisk--chan_h323-->GnuGK--->AS5300-->PSTN boldsoft*CLI> show version Asterisk CVS-v1-0-03/24/06-15:27:08 built by root@boldsoft on a i686 running Linux I can make