similar to: Cisco 7960 sccp, Skinny and 1.4

Hi all, I'm writing my graduation theses : analysis VO-IP protocols , and I cannot find any documents about Cisko Skinny Client Control Protocol. I have Cisco CallManager and some IP-phone and I'm sniffing traffic between that, but I don't understand, how this protocol works. Clearly i'm looking for description of SCCP commands and explanation some basic SCCP scenarios or what

Hi, please tell me, is original skinny support in Asterisk stil under development or is better to try chan_sccp from http://chan-sccp.sourceforge.net ? my first try was unsuccessfull (chan_sccp compile OK, but module loading fail during Asterisk startup) and my phone (C7940) seems to be not supported in original chan_skinny :( PJ

I wonder if Asterisk's skinny/sccp channel driver could be used as a "client" to register with a Cisco PBX. That is, along with a SIP client, say, have Asterisk and said SIP client stand in for a Cisco phone, or an IP Communicator. Anyone done this? Cheers, b. -------------- next part -------------- A non-text attachment was scrubbed... Name: not available Type:

Greetings: I have a working configuration for SCCP on our LANS which doesn't route RTP correctly to a skinny phone behind NAT registering from a remote public IP. Configuration: asterisk 1.4.35 servicing only skinny phones trunked to asterisk 1.2.40 which services chan_phone FXS, zap FXO and SIP phones; both instances of asterisk are behind NAT and run on the same host (using different base

Before I got down the path of converting a Cisco 7960 I have over to SIP I wanted to try and set it up using Skinny. The phone registers ok with Asterisk. When I call a SIP softphone extension on my network the call is made and I can answering it. However no voice is heard over the call. When I debug Skinny on the console after the call has connected I see the following messag: Recieved Alarm

Hi list! I'm trying to configure the Kirk IP 600 wireless (DECT) system. The wireless phones are regular DECT phones, the Kirk IP 600 is doing the voip part by registering/gatewaying the phones to a callmanager server. The phones do not work and I think the problem is that they do not register at asterisk but I'm not sure because I don't understand a thing of the sccp/skinny

Can skinny work behind NAT? I have a Cisco 7910 using SCCP behind NAT that has one way audio. The called party cannot hear the calling party who's using the 7910. skinny.conf ; ; Skinny Configuration for Asterisk ; [general] port = 2000 ; Port to bind to, default tcp/2000 bindaddr = 0.0.0.0 ; Address to bind to dateFormat = M-D-Y ; M,D,Y in any order (5 chars max)

I could use some skinny/Cisco help here. Was finally able to get the phone registered to * but whenever someone tries to call that phone it freezes and reboots itself. Same thing happens when you pick the handset up off the 7960G; it locks and reboots about 5 sec later. Here is what * shows when I plug the phone in: -- Starting Skinny session from 64.72.107.1 Device SEP000F3442E4A7 is

Hi All; Again, the Cisco IP Phones 7942G and using Skinny: I upgraded the firmware to version 8.5 (skinny) and I am using skinny channel (chan_skinny) and the skinny.conf file. The phones are registering, but when we use them to place a call, we only hear tooooooooooo in the handset and we do not hear voice (even when we dial the digits, we only hear toooooooo .. but it dials and destination

I have a cisco 7910 phone, I'm trying to get it to connect to asterisk, But it seems like it needs either a SEPDefault.cnf file or a SEPMACADDR.cnf file to Continue, I created empty ones but it's still sitting there saying "opening" Does anyone have examples of the SEPDefault.cnf file? Kevin,

Hi, I have bought two Cisco 7960 phones. I have tried to set-up them to work with Asterisk over Skinny protocol, but when I try to dial the phone from Asterisk it says that all lines are busy. Is there something that should be configured on the phone's side? Can someone help me with that? Also, I would like to upgrade these phones to use SIP. How can I get the SIP firmware for my phones. I

Hi All; Can anyone advise if using Cisco IP Phones in skinny protocol is fine or not? Or it is better to use it in SIP protocol? Regards Bilal

Hi! I have two, not too related questions: - the probably simpler one: if anyone can help me out using a Cisco 7905G with chan_sccp? I did already managed to get it working with a SIP image, I'd just like to see it work with this one as well. It's probably something I screw up with the configuration, as the phone registers, only I don't get any lines with it, although I have it

Hello, I tried to configure a cisco 7905 IP phone using the skinny channel but I had not much luck. The relevant portion of skinny.conf is: [cisco1] device=SEP000F3487F8E3 callerid="Alex" <123-456-789> mailbox=500 callwaiting=1 transfer=1 context=default threewaycalling=1 line => 500 ; Dial(Skinny/500@cisco1) I set up the tftp server, and prepared the following

Is there a place where I can find documentation on the Skinny protocol in Asterisk? I did a search, but I cannot seem to find much... I'm looking for information on how to get a Cisco 7960 with the CM image on it to work with asterisk.. Is it support for Skinny in asterisk even mature enough to be able to do this? Thanks, - Andre

I found a few mentions of the 7914 being used with Asterisk, these all covered SCCP/skinny though. Does anyone know if the 7914 can even be used with SIP? If so, any pointers? Is it a services thing? Anyone get the operator (line/extension status) to work with it. Thanks for the help, Cisco doesn't even mention ANYTHING about SIP + the 7914. Matt

hi All, Sorry to repost but................ I have a server setup that runs sip no problem. I want to try a cisco phone. how do I a) Tell if I have skinny support loaded b) Load it onto a debian system Many thanks

Can someone provide example configuration files and/or instructions for configuring Asterisk to work with chan_sccp2 and a 7960. I have the searched the chan_sccp2 site, the voip_info wiki site, asterisk doc project, and mailing list archives for the past year for help, but failed to find anything helpful. Some of the questions I have are: 1. What settings need to be made on the phone? 2.

Hi again, I found chan_skinny and that seems to work pretty good. the SCCP one filled out all the buttons really nice, but skinny seems to be working. How do I fill out the second line button on the phone with skinny.conf? Thanks much! ...Jeff

Hi list! Does anyone have experiences with the updated model of the Kirk IP600? The V3 model is supposed to support SIP instead of only SCCP or H323 which would make the use with Asterisk a lot easier. I have only tested the Kirk IP600 V2 with SCCP / Skinny protocol which is still giving me severe headaches : - the standard Skinny driver in * doesn't work, only the version of Sergio