similar to: Sangoma FXO/FXS config

Hi, I have a TrixBox install with a Sangoma A200 and 4 FXO ports, there are 3 BT lines connected directly to these ports. One of the lines has BT FeatureLine Compact and this is the line I am having problems with, the other 2 lines are working perfectly, detecting CID, answering incoming calls and placing external calls via SIP devices. I am receiving a error log entry: chan_zap.c:

Hi I have been having a rough time getting a Sangoma A200/Remora FXO/ FXS Analog AFT card set up properly. The main issue is that the card has four ports and as far as I can tell Asterisk is only seeing two. On the two that it recognizes the "Green" FXS ports are not green, they just are not lit. The "RED" FXO ports are indeed red, but from what I have read your not

Evening all. I'm looking at building an Asterisk system for one of the projects of the Charity where I'm the SysAdmin. The project has two analogue phone lines - BT Featureline Compact, we're in the UK - that I'd like Asterisk to handle. My current quandary is which FXO interface to use. I've been looking at the Digium TDM400P and Sangoma A200, which are similar prices for

Hi, I'm trying to install asterisk(v1.2.22) with FreepBX(v2.2.3) with a 4-Port FXO Sangoma card A200. I'm using Fedora 7 (x86_64) kernel version 2.6.22.1-27.fc7, but i'm having these errors: $ ztcfg -vvvv Channel map: Channel 01: FXS Kewlstart (Default) (Slaves: 01) Channel 02: FXS Kewlstart (Default) (Slaves: 02) Channel 03: FXS Kewlstart (Default) (Slaves: 03) Channel 04: FXS

Hi- I'm totally stumped configuring my TDM400P with one FXS and one FXO module. Before I got the FXO module, I used to have an X101P, and everything was working very well. Now * doesn't seem to recognize the FXO channel. I've searched the wiki and the list archives. Stock Debian 3.0 stable installation. Any advice? Thanks. -- David Here's my configuration: modprobe zaptel

Hi. I am having problems with dahdi using kernel 2.6.32. I am using 2.6.30 kernel and it works fine -- here is the output of dahdi_cfg -vv ++ dahdi_cfg -vv DAHDI Tools Version - SVN-trunk-r8670 DAHDI Version: SVN-trunk-r7445M Echo Canceller(s): Configuration ====================== Channel map: Channel 01: FXO Kewlstart (Default) (Echo Canceler: mg2) (Slaves: 01) Channel 04: FXS Kewlstart

Hi , I have an asterix (1.2.7.1) box with 3 TDM400P and 10 FXO modules, and zaptel (1.2.5). The problem is that 6 modules can't be initaized and i get the folowing error: May 7 09:17:37 WARNING[7739] chan_zap.c: Unable to specify channel 9: No such device May 7 09:17:37 ERROR[7739] chan_zap.c: Unable to open channel 9: No such device here = 0, tmp->channel = 9, channel = 9 ztcfg output

Hi I am in the middle of move a small business over from legacy PABX + PSTN lines to VOIP infrastructure. I borrowed a spa9000 to place between the PABX and the PSTN lines. I have had this going for a while (>5 months) and it has been working fine (some issues with echo and other minor things), which is why I am moving to asterisk. I bought a tdm410 with 3 fxo + fxs. The fxs is connected to

Hello, After installing on Ubuntu 10.04 using the tutorial on http://hmontoliu.blogspot.com/2010/03/installing-asterisk-and-freepbx-on.html I have a running instance of Asterisk. PROBLEM: result of dahdi_cfg: DAHDI Tools Version - 2.2.1 DAHDI Version: 2.2.1 Echo Canceller(s): MG2 Configuration ====================== Channel map: Channel 01: FXS Kewlstart (Default) (Echo Canceler: mg2)

Hi all, i've installed AMP and Asterisk following the INSTALL file and i have a problem with the TDM04B with 4 FXO: [root@srvoip ~]# ztcfg -vv Zaptel Configuration ====================== Channel map: Channel 01: FXO Kewlstart (Default) (Slaves: 01) Channel 02: FXO Kewlstart (Default) (Slaves: 02) Channel 03: FXO Kewlstart (Default) (Slaves: 03) Channel 04: FXO Kewlstart (Default)

I just got a brand new A101 and am trying to install it in my test Asterisk box. The install went without a hitch. I followed the directions on the Sangoma Wiki: Wanpipe Asterisk Install http://sangoma.editme.com/wanpipe-linux-asterisk-install Wanpipe for Asterisk Configuration http://sangoma.editme.com/wanpipe-asterisk-configure It went perfect, no problems and Asterisk came up fine. I downed

I am having trouble with chan_zap.so not loading. When I load it from modules.conf, Asterisk bails out without any error message. When I load it from the console, it just says "Unable to load module chan_zap.so" no matter what verbose level I am using. dmesg says: Zaptel Version: 1.4.4 Zaptel Echo Canceller: MG2 Freshmaker version: 73 Freshmaker passed register test Module 0:

after installing asterisk 1.4.23.1 and dahdi-linux-2.1.0.4 and at CLI> module load chan_dahdi.so receive the following: signalling must be specified before any channels are. CLI> Warning [4663]: chan_dahdi.c:11627 process_dahdi: Ignoring signalling Error[4663]: chan_dahdi.c:10946 build_channels: Unable to reconfigure channel '1' Error[4663]:

I think I have a bad FXS module on my TDM400P. Channel map: >> >> Channel 01: FXO Kewlstart (Default) (Slaves: 01) >> Channel 02: FXS Kewlstart (Default) (Slaves: 02) >> >> 2 channels configured. >> ZT_CHANCONFIG failed on channel 1: No such device or address (6) The zaptel loads ok, but the wctdm reports No such device or address and stays loaded. The

Hello List, Im just dipping my feet into the asterisk world, and im having major fxo problems Im running Asterisk (from svn) + libpri (from svn) + asterisk-addons (from svn) + asterisk gui (svn 1.4 branch) + zaptel (svn 1.4) on a Debian Etch box, with 1gb ram, running all of the services for my home server (web / db / music server etc), and i would like to run my PSTN line from Kingston Comms,

I've got the latest zaptel and cvs asterisk software loaded on my phone server running FC3. And yes, It's fully updated and udev is setup correctly. I've got a TDM400P with one FXS and one FXO module installed. When I load zaptel and wctdm and run ztcfg -vvv, I get this: [root@asterisk ~]# ztcfg -vvv ZT_CHANCONFIG failed on channel 1: No such device or address (6) Zaptel

I have a TMD400 card installed in a PC with one fxs (installed in slot 2) and two fxos (installed in slots 3 & 4).? fxos work fine but I am unable to get a dial tone for any devices connected to the fxs.? I have correctly connected the power supply to the card and I have even tried moving the card from slot 1 to 2 on the board. Below is from the console when I try to route a call from FXO on

Hi, I recently purchased two X100Ps and a TMD40B. I have set everything up according to the instructions however I can't get asterisk to pick up an incoming call (It just keeps ringing). Also, when I pick up an internal extension I get dead air. I searched the mailing list for 3+ hours -- What am I missing? Thanks in advance for your help. Here are the installion steps that I used:

I recently updated (fresh checkout) to the newest zaptel and Asterisk. The one I was using before was a couple of months old. After updating, my zap channels don't work. They won't pick up incoming calls or dial out. When I try to dial out I get: -- Executing Dial("SIP/3064-564c", "Zap/g1/ww954.......") in new stack NOTICE[245776]: File app_dial.c, Line 698

I have a TDM400. Just updated Fedora 12 to kernel 2.6.32. Rebuilt and installed dahdi-2.2.1. kernel modules loaded. lsmod | grep wctdm wctdm 37233 0 dahdi 194985 1 wctdm lsmod | grep dahdi dahdi 194985 1 wctdm crc_ccitt 1549 2 dahdi,isdnhdlc dmesg: dahdi: Telephony Interface Registered on major 196 dahdi: Version: 2.2.1