similar to: [URGENT] Zap channels fail to load

Hi, We have got a new PRI card at one of our Office locations and now I need to install the the device on a remote server. Is there any way to know if the device is loaded already. When I give " cat /proc/zaptel/* " it returns the following. # cat /proc/zaptel/* Span 1: WCT1/0 "Wildcard TE122 Card 0" (MASTER) B8ZS/ESF RED IRQ misses: 2 1 WCT1/0/1

Hi guys I have a lovely little irritation on my hands. I?ve been trying to set up DID-based routing in Hylafax, and I?ve come across one hell of a headache:

Hi guys I've just read this about the upcoming release of * 1.6: ?Better reporting through a new call event logging capability in Asterisk 1.6 will allow complete tracking of events that take place during a call. The goal, according to Fleming, is to provide more detail than traditional CDR (Call Detail Recording) features offer and to allow for more granular tracking and auditing.? That

Hi, all My Asterisk uses a Digium TE120Pand I would like to add an Astribank zaptel_hardware sees is, but I cannot get it working pbx:~# zaptel_hardware Argument "IRQ" isn't numeric in numeric comparison (<=>) at /usr/local/share/perl/5.8.8/Zaptel/Span.pm line 114. usb:005/002 xpp_usb- e4e4:1131 Astribank-8/16 USB-firmware pci:0000:04:00.0 wcte12xp+

Hi all I have a small problem here. I asked this question on another asterisk mailing list, but nobody seemed to be able to help me there. We are running * Asterisk 1.4.17 * Libpri 1.4.3 * Zaptel 1.4.8 on a 1.6 dual core, 2GB ram and a digium TDM800P wildcard, hardware echo cancelation and a quad FXO card. We have 4 analog lines, one of which is a Cellphone line for least cost

Hi, I configured an asterisk box with 1 Digium Wildcard TE110P T1/E1 Card 0 I setup the jumper in e1 position. my zaptel.conf : defaultzone=it loadzone=it #gestione PRI span=1,0,0,ccs,hdb3,crc4,yellow bchan=1-15 # set this to 1-15,17-31 for E1 dchan=16 # set this to 16 for E1 bchan=17-31 # set this to 1-15,17-31 for E1 # Asterisk starts correctly, I see th 30 channels. Anyway I cannot put

Hello, I have a problem with zaptel. I hope you can help me. I installed and configure zaptel. ZAPTEL.CONF span=1,1,0,ccs,hdb3,crc4 bchan=1-15,17-31 dchan=16 loadzone = de defaultzone=de But the output of cat /proc/zaptel/* Span 1: WCT1/0 "Digium Wildcard TE110P T1/E1 Card 0" (MASTER) HDB3/CCS/CRC4 RECOVERING 1 WCT1/0/1 Clear (In use) RED

Hi, I'm having trouble configuring and E1 link , I know the E1 is a PRI and the switchtype is 5ess. The problem is that everytime I try to dial I got and error saying that it was unable to open the zap channel . Devices are created in the /dev/zap directory and I can open them with a cat /dev/zap/1. I can also see the channels in /proc/zaptel/1. Thanks in advance [zaptel.conf]

I have configured /etc/asterisk/zapata.conf, but now Asterisk refuses to start: Aug 5 10:47:29 ERROR[1076842624]: chan_zap.c:5976 mkintf: Unable to get parameters Aug 5 10:47:29 ERROR[1076842624]: chan_zap.c:9478 setup_zap: Unable to register channel '1-15' Aug 5 10:47:29 WARNING[1076842624]: loader.c:328 ast_load_resource: chan_zap.so: load_module failed, returning -1 == Unregistered

Hi @ all, i set a server to a costumer of mine with a TE207P for use with 2 E1 Lines. I set them together into one group in zaptel/zapata.conf The point is now, the customer has a free-volumina of 60k minutes per month, per line. How can i make a kind of load balancing, that both lines will be trafficed the same way ? I read something about DIAL(Zap/r1/.) for using round robin, and

Hello all, I've got a T100P connected to an Adtran TA750 with a T1 crossover... This connects to a patch panel with phone ports. The Adtran is fully populated with FXS cards. All I get on any phone port is a fast clicking noise... No dialtone. Asterisk 'sees' the card, (the channels show up in /proc/zaptel). Incoming calls are routed to the zap/x channel, but no ring. I'm

I have a pair of sites tied together with a T1 line running zaptel PPP on either end. The system works, but I keep getting these messages in the kernel logs, and users are reporting connection problems (TCP timeouts, and hangs) especially under high usage. --snip-- HDLC Receiver overrun on channel WCT1/0/1 (master=WCT1/0/1) HDLC Receiver overrun on channel WCT1/0/1 (master=WCT1/0/1) HDLC

Dear all, I have small question in sip.conf I added [service] type=friend ;username= ;secret= qualify=900 host=X.X.X.X dtmfmode = rfc2833 disallow=all ;allow=g729 allow=gsm allow=alaw allow=ulaw and I can proccess incoming call from soft phone only I calling on number that is used in extensions.conf(in example below it is 1) exten => 1,1,Answer; exten => 1,2,Playback(hello-world,skip);

Hello everyone, I want to connect a fax to an FXS port (TDM420P). For testing purposes, I connected an analogue phone to it first. However, when I pick it up, I cannot hear anything at all. The power cable is plugged into the card, the port is configured to use fxo-signalling. Also, immediate=no. Here's the files: /etc/zaptel.conf: # Autogenerated by /usr/sbin/genzaptelconf -- do not hand

Hi, all I want to configure a few FXS ports in an Antribank-16 to be able to receive faxes sent throught a PRI: E1 ==>Zap * ==>FXS * ==>Fax machine My asterisk box has a Digium TE120P (for the PRI). Versions are *=> 1.4.17 | Zaptel=>1.4.8 | libpri=>1.4.5 The Astribank is not configured yet, because I am a little bit confused about how to do it. Let's say I configure

I am aware of how to match a particular caller-id or a caller-id pattern and do something with the call like this: exten => 15554441212/_888NXXXXXX,n,Playback(GoAway) What I am curious about, is the best way to block unknown, private and 000-000-0000 calls. I know I can do this for 000-000-0000 calls: exten => 15554441212/0000000000,n,Playback(GoAway) Is there a better way to catch

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi all I am working in a new set up with Grandstream GXP-2000 handsets. I like those phone, but they lack a feature I need: the phone cannot be locked by the user. What I actually want is a user to be able to avoid someone else making calls from his phone without giving him access to SIP configuration access to the phone. i.e. let say I want user

Hello ml, i need some help on my zaptel configuration. My E100P only shows some YELLOW / RED alarm when I load the wct1xxp module and do a cat /proc/zaptel/1 Span 1: WCT1/0 "Digium Wildcard E100P E1/PRA Card 0" HDB3/CCS YELLOW RED ... .. . My /etc/zaptel.conf is: span=1,1,0,ccs,hdb3 bchan=1-15,17-31 dchan=16 loadzone=nl defaultzone=nl I tried zaptel-1.0RC2 and the latest CVS

hi every body; i installed zaptel 1.4,libpri 1.4, asterisk 1.4, asterisk-addons 1.4 succefuly, but i can't find the command "genzaptelconf, so i tink to install "handy zaptel toolset" please can someone tell me whitch package goes with zaptel 1.4, i consult "http://updates.xorcom.com/rapid/pool/main/z/zaptel/" but ????????????

Ok I F@%& up. I didn't realize the card is 3.3 volts and my new computer is 5V. Can anyone point me to a PCI to PCI bridge. Any suggestions? Mike