similar to: Best config for 12 FXO system?

When I use my phone to make VOIP call and another calls comes from POTS my phone rings to POTS caller. Why? Shouldn't it generate busy signal! -- #Joseph

Dear all I have TDM808B 8 port FXO it is configure perfectly but i got some problem of incomming phone Hangup and callerid display problem i am going to explain you the issue i have install asterisk 1.4 and i have 100 of SIP phone now everything is fine but problem is when i incoming call on FXO and dial sip extention SIP phone is rining but when i disconnect my incoming

I am trying to use TE110p card for Euro ISDN with Ericsson AMS switch. I consistently get one of the following errors: PRI got event: HDLC Abort (6) on Primary D-channel of span 1 or PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 1 My zaptel.conf file: -------------------------------- span=1,0,0,ccs,hdb3,crc4 bchan=1-15,17-31 dchan=16 loadzone=us defaultzone=us

Hi all. I've being reading posts from the list since yesterday and I feel this question was answered a lot time ago, but the list archives are a mess (yet). I hope some one is willing to help me out. I want to set up this: caller ----- PSTN ---- (SOMETHING1) ------ VoIP --------- (SOMETHING2) ---- PSTN I think this must be a very basic architecture, but I'm not sure wat SOMETHING1

I have been asked by a potential customer whether we can connect an Asterisk box to an Ericsson MD110 that has an E1 port with ISDN-USR. They are unable or unwilling to upgrade their E1 port to QSIG. Has anyone here had experience of successfully making such a connection? I have found a couple of hits on Google that suggest it "should" work, but I'm after something a little more

Hi, during gradual migration to Asterisk, I put Asterisk in front of a legacy Alcatel PBX: PRI PSTN <--> Asterisk <--> E1 cable <--> Alcatel PBX After successful deployment of VoIP phones, it's time to drop Alcatel PBX! I'd like to keep some of analog lines to support modem, fax and some older stuff. What's the best choice? A channel bank or a TDM2400P card? Can I

Hi list! I'm trying to setup Digium TE205P E1 card to work with my provider (and Ericsson BP 250 - this comes later). When I execute "pri show span 1" this is what I get. pbxzg1*CLI> zap show status Description Alarms IRQ bpviol CRC4 T2XXP (PCI) Card 0 Span 1 OK 0 0 0 T2XXP (PCI) Card 0 Span 2 UNCONFIGUR 0 0 0 pbxzg1*CLI> pri show span 1 Primary D-channel: 16 Status:

Hi, I have a box with Debian Sarge, Asterisk 1.2.1 (and zaptel 1.2.1) and a TDM2400P with echo canceller. I installed the card but no echo cancellation is being made...seems like the echo canceller module does not work, infact the software cancellation is working. My zapata.conf has echocancel = 128 and echocancelwhenbridged = yes but no echotraining parameter which gives a warning. I found

Hi i have a tdm2400p and installed asterisk 1.4.11 with zaptel 1.4.5 im having an error message when in running asterisk with the tdm card in. here's the error from the console of asterisk: [Nov 18 10:30:44] ERROR[5557]: chan_zap.c:7489 mkintf: Unable to get span status: Inappropriate ioctl for device [Nov 18 10:30:44] ERROR[5557]: chan_zap.c:10466 build_channels: Unable to register channel

Hi, I'd like to change 3 TDM400p with one TDM2400p to avoid echo (my intention is to use a TDM2400P echo cancel module). It TDM2400p working good with asterisk 1.2.1? Or I need to install a new asterisk version? TIA Giorgio Incantalupo

We just bougth a tdm2400p with all the modules for FXO, but we are having some troubles with the card, cause it aparently is stripping some digits from the dialed number, we tested the same server with a tdm400 and everything worked as expected. We?ve already added "w" before the dialed number with no results, is there any way to solve, is it a bug thanks

Hi all, I'm confused, in digium website, it says: TDM2400P: It supports a combination of up to 6 FXS and/or FXO modules for a total of 24 lines. 6 plus 6 is 12, how come it's 24? if I have 24 PSTN lines, i'll be needing 24 FXOs. Pls. elaborate. thanks. Lito -------------- next part -------------- An HTML attachment was scrubbed... URL:

How many TDM2400P cards can I safelly install in one PC? I'm loking for answers from whoever has a working scenario with * and a number of cards higher than one. Thx, Juan __________________________________________________________ Mensagem enviada usando o Webmail da ViaLink ver. 2.7.8

Hi all, I have TDM2406E with 24FXO ports connecting to 10 POTS line sitting in my office. the out going calls symptom like when called party pickup the phone but the calling party still hearing the ring tone from the IP phone. Please light me up. it been many sleepless night by googling around trying to get the right answers. The digium card running on Intel 915G chipset. Below are my zaptel

Hello. I have a TE212 configured in E1 mode. This is shown in a cat /proc/zaptel/2 and 3 (where the card is configured): cat /proc/zaptel/2 Span 2: TE2/0/1 "T2XXP (PCI) Card 0 Span 1" HDB3/CCS/CRC4 RED NOTOPEN 25 TE2/0/1/1 Clear 26 TE2/0/1/2 Clear 27 TE2/0/1/3 Clear 28 TE2/0/1/4 Clear 29 TE2/0/1/5 Clear 30 TE2/0/1/6 Clear

Hi, A week or so ago I wrote about the problems I was having using a Digium TDM04B card in a Dell PowerEdge 750 IU running Fedora Core 1. Digium steadfastly indicates their card won't work in any PowerEdge 650, 700 and 750 series machines "do (sic) to a failure in interrupt handling between the pci bus and the card." My question to the list is: for those of you using a TDM04B

I am having a problem with a couple servers. They both have a Digium TE110P and a TDM04B card. I have setup the system so the TE110P uses channels 1-31 and the TDM04B 32-35. The problem is that when we reboot the server sometimes the TDM04B is recognized first and the TE110P second so the configuration fails. I do not know why this happens and to solve this I have to do a "service

Hi, I am getting half channel audio on cisco 7960? Any idea why? Details below. Jerry This same phone has been working for MONTHS using a TDM2400p with no issues. Today we got a T1 installed coming into Box A with all incoming calls going to Box B (the TDM2400P box). The TDM2400 is no longer in use. All incoming and outgoing calls are done with the T1 and Box A and Box B use SIP between them

I've been asked to assess the cost of implementing Asterisk with a single T1 line in one of our offices. I've had plenty of experience w/ TDM400 cards, but T1 is new for me so a couple of questions: 1) Will I need a digital or analogue interface card? I expect digital is the answer, but the Digium web site said something about analogue cards being able to support "provider T1

I would like to install a TDM04B with Asterisk@Home 2.4 and Asterisk@Home 1.5 but I didn't find documentation about this installation. Thanks in advance, Nelson -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20060206/85ff5252/attachment.htm