similar to: E&M Wink and T4xxP losing ability to dial

I have a TE410P with two real Telco T1's and the other 2 ports terminate into an in-house voice mail/IVR system. Calls arrive from Telco are routed to the appropriate in-house system based on the DID Digits. This part works perfectly. Now I what to allow the in-house VMS to dial though asterisk to the Telco T1's. The VMS complains there is no dial tone on its T1 and drops the attempt.

I have a couple of questions on the zapbarge: 1) zapbarge asks for a channel - how would a manager know what channel to enter ? Is there any way of being able to enter an extension number instead ? I know that you can get the information from the manager interface, but I wouldn't want to give my users access to this, or have to install / write a system just to get an extension number from a

Hi, Did anyone manage to connect either Digium or Sangoma T1 card to any other PBX/gateway using T1 E&M Wink/Wink signaling? I'm trying to connect Avaya Definity to an Asterisk box with T100P and so far no luck. (I know I can do so with ISDN PRI, but need an additional ISDN processor card for Definity.) I tried to connect Definity to Cisco 3640 CCME (call manager express) to test the link

I could only get *ANI*DNIS* working one way and that was setting my signalling type on the Asterisk side to 'featd' The Definity won't send *ANI*DNIS* information back to the asterisk as far as I can tell. Other than that, I've been running it with wink/wink E&M for a while now. TN464 circuit pack on the definity side, te110p on the asterisk side. Just a crossover cable

Attempting to talk to an Eagle Telephonics switch at a disaster exercise. Didn't think a plain old E&M wink start T1 would be this much of an issue. We finally got the Eagle to accept a call from *, but whilst I can hear the person on the Eagle, they can't hear me. When they initiate a dial out I only get the first 2 digits from their switch... Does anyone have decent

We're having some difficulty connecting a T1 fax board card to asterisk, with E&M Wink. We've successfully connected it to other E&M Wink T1s, but have been unable to get asterisk to hear it's dialing. Asterisk can dial down to it with no problem, and it hears all the digits, but whenever it sends digits down to asterisk, * always only "gets" the first one. This is

I am preparing to connect an asterisk box with a redfone fonebridge to a T1 service provider. I am doing this by testing first with another asterisk and a Sangoma card playing the role of telco. I formerly had this test configuration operating flawlessly as a PRI connection. But I discovered that I will need to use E&M, thus I've chosen the parameters as described in the subject

Hi List, I have some T1 750s; hookup via a T1 to a TE420P card. We have them all set as E&M wink trunks. We get a dial tone and can call numbers, but when i call another number the ringing I hear on my phone is very weird, its not the standard ring tone. What will cause this? Is this a * setting or something in the Adtran I am fixing, I just want good ole ringing to be heard! Any help would

List: I already have asterisks up and running on a PRI, but where we are moving we cannot get a PRI so we are going to get T1. My question is: We are going to us E&M Wink for signaling with DTMF and caller id. The channels are going to be setup like this, 12 channels for 2-way and 12 channels for incoming only with DIDs. How would I configure the zaptel.conf? I realize that I will have two

I'm trying to get a patch tested for inclusion in CVS. Anyone that is running E&M on a T1 and had to fool around with emdigitwait could you please try this. This patch removes the need for the emdigitwait parameter and speeds up dialing. This situation is mostly interfacing a legacy PBX/Key system with Asterisk. I've been running a couple of systems with this patch for

I am setting up a box with a T100P. Everything is going well. The company I am working with has their one phone switch gear. They provisioned me a E&M Wink T1. Cannot do PRI unfortunately. We chose E&M so we could pass an unlimited number of DIDs to the trunk as apposed to FXS loopstart signaling. I can make outbound calls no problem, but I am having problems with the dial plan for inbound

I'm getting red alarms with my T100P card that last from 4-15 seconds. They seem to happen randomly, every couple of days. Has anyone seen this behavior, or does anyone have any ideas regarding what would be causing it? Thanks, Glen

Anyone successfully implemented a solution for allowing ZapBarge call monitoring only for a specific group of agents calls? The issue I see is that the feature only works on zap channels, and all of the agents (in many cases) are IP phones. Allowing ZapBarge and ZapScan on the TDM PSTN (t100p) interface has privacy issues for senior managers, but would allow all outbound zap calls to be

I am an Asterisk newby, and I cannot seem to get Caller ID information from our T1 line. When calls appear at the phones, they say the call came from "asterisk" and unknown number. I know how Caller ID information is passed on an analog phone line (between the rings) but with a T1 line, I don't know technically how it is done. I don't see the caller's number in the

Hello, I've got very annoying behaviour from our asterisk PBX. We have 12 channels T1 e&m wink start for TDM and using iax softphones internally (iaxcomm, but tried firefly-thirdparty and discarded for bad sound quality). Slackware 9.1 w/ kernel 2.4.26+ digium TE110P card. In some cases when call is placed from softphone to TDM, system does not detect call answered on Zap channel and

I've got a couple of different situations where I'd like to do something like zapbarge into a specific channel but I'd like to be able to actually talk to the party or parties on the channels, not just listen like w/ zapbarge. There are two scenarios I can think of right now where it'd be very handy. a) when the outside line is ringing and Asterisk is waiting to answer or

Hi All, I have a rather peculiar problem. Whenever I dial out over ZAP/g0 the phone will just ring and ring, even if I answer the phone on the other end. Whats strange is that the * phone will continue to ring even after I've answered and (sometimes) hung up the dialed phone. If I make an extension to just directly dial out on ZAP/1, its almost the same behavior, it will continue to

Maybe one of you can help me with this: We have T1's that come from both MCI and Global Crossing as uses channelized (24 Ports per T) with inband (DTMF) ANI and DNIS delivery (format = *DNIS*ANI*). My old equipment was set for D4, AMI, SF and Wink Start and so is Asterisk Server. I've moved these T's to Asterisk TE410P and inbound calls are arriving to external voice mail

I'm using a TE405p with all four spans enabled, two configured as pri_cpe and two as pri_net, the asterisk is sitting between our ISDN (UK BT EuroISDN30) and our phone system. We have 200 DDI numbers on the ISDN's and I need to give one of our clients dial-in access to be able to monitor calls we handle on their behalf. I've got ZapBarge working but I need to restrict the client

Maybe of you guys know the answer to this: We have T1's that come from both MCI and Global Crossing as channelized (24 Ports per T) with inband (DTMF) delivery of ANI and DNIS (format = *DNIS*ANI*). My old equipment was set for D4, AMI, SF and Wink Start and so is Asterisk. I've moved these T's to Asterisk TE410P and inbound calls are arriving to external voice mail system