similar to: Supermicro PDSME+ and TE110P

Hello, Digium support kindly proposed to ship a TE120P card to help resolve the issue. I plugged in the card, and introduced the loopback plug. I cleared the red alarm for a while and then i started seeing alarm switching from Yel/Recovering to Blue/Rec with a lot of IRQ Misses. I call Digium that assisted us, and we noticed IRQ sharing with the VGA adapter and the Ethernet port. I changed

Hello Everyone, I checked with zttool that sometimes after the machine boots the order of the boards is changed like this: ??? Alarms Span ??? OK Digium Wildcard TE110P T1/E1 Card 0 ??? OK Digium Wildcard TE110P

I have an Asterisk server that was running fine until Sunday. Monday there was a power outage and the server was off most of the day. This server has a TE110P, two TDM04B and an Astribank 32. Today I noticed that the TE110P started having IRQ missess. Before today it only had about two or three per month. Today, this is the miss count after ten minutes on: IRQ Misses: 1443

Hi I'm having difficulties getting up my TE110P (running as a E1) when I connect it to the PRI. If I start the server with a loopback connector everything seems fine and the led is green but when I connect it to the PRI the flashing starts .... I can't seem to find anything in the log that suggests what could be wrong .....Aug 8 11:33:00 DEBUG[1369]: Updated conferencing on 31,

Hi guys, I've been installing and configuring a TE110p card. The compile and install went very well. I'm using this on FC4 and I compile with linux26 as well checked I on the udev configs. zttool and ztcfg both indicate that the card is ready. But when I try to "load chan_zap.so" then I get the following Unable to load module chan_zap.so Jan 5 21:43:33 ERROR[6808]:

http://bugzilla.mindrot.org/show_bug.cgi?id=1013 sigmunds at iu.hio.no changed: What |Removed |Added ---------------------------------------------------------------------------- Summary|openssh > 3.8p1 make failure|openssh > 3.8p1 make failure | |on Solaris ------- Additional Comments From

Has anyone had any compatibility issues with a TE110P card installed on a Dell Poweredge 1950? I noted the following error on the LCD display of the Dell Poweredge 1950: E1711 PCI PErr Slot 1 E171F PCIE Fatal Error B0 D4 F0. The Dell hardware owners manual states that it means the system BIOS has reported a PCI parity error on a component that resides in PCI configuration space at bus 0,

Guys. I have an issue with a te110p card and also some tdm04b cards on the same system: Zttest returns this for the tdm04b cards: [root@mollendo ~]# /usr/src/zaptel-1.2.4/zttest 38 -v Opened pseudo zap interface, measuring accuracy... 8192 samples in 8191 sample intervals 99.987793% 8192 samples in 8192 sample intervals 100.000000% 8192 samples in 8192 sample intervals 100.000000% 8192 samples

Helo, I have problem with Digium TE110P connected to CISCO 3640 (port on NM-HDV-2E1-60) wth PRI E1 link. I use CISCO now for testing but when I tried with real PBX problem was exactly same. I have this messages in Asterisk conole and log sometimes: NOTICE[1115] chan_zap.c: PRI got event: HDLC Abort (6) on Primary D-channel of span 1 Usually 2-5 such messages in series, can be repeated after 10

Hello I just installed a TE110P in a Dell Poweredge 750 (rackmount), which is connected via crossover T1 cable to a adit 600. Anyway, I've encountered an array of errors, which I believe I have narrowed down to the 22 IRQ misses I encounter on zttool. I've noticed that the te110p and the usb device share an IRQ. Could that be the source of my woes? Would disabling the usb device in the

Perhaps everything isn't as spiffy as I thought When running zttool the card still reports as internally clocked Zaptel.conf: # Global data span=1,1,0,ccs,hdb3,crc4 bchan=1-15 dchan=16 bchan=17-31 loadzone=se defaultzone=se And as pointed out by Peter I do get a lot of D-channel warnings ... Aug 9 16:21:25 NOTICE[1350]: PRI got event: HDLC Bad FCS (8) on Primary D-channel of span 1 And

Hello all. I have here a TE110P (configured as E1) and a TDM400P (with four X100P - FXS). Both boards are recognized by the operating system as showed above: 0000:08:00.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface Subsystem: Unknown device b1d9:0003 Flags: bus master, medium devsel, latency 64, IRQ 169 I/O ports at e800 [size=256]

http://bugzilla.mindrot.org/show_bug.cgi?id=1013 Summary: openssh > 3.8p1 make failure Product: Portable OpenSSH Version: 4.0p1 Platform: All OS/Version: Solaris Status: NEW Severity: critical Priority: P2 Component: Build system AssignedTo: openssh-bugs at mindrot.org ReportedBy:

Does anyone know if you can have multiple TE110P cards in one chassis? -Thermal -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20061011/adbceeb5/attachment.htm

Hi! I'm trying to setup a Wildcard TE110P with a PRI in The Netherlands. I get a Red Alarm on the line. Is there any way of debugging this? I've tried some configs that should work but without success. Is there any way of telling if the cabling is correct or what else the problem could be? Thanks!! Remco

Hi, I configured an asterisk box with 1 Digium Wildcard TE110P T1/E1 Card 0 I setup the jumper in e1 position. my zaptel.conf : defaultzone=it loadzone=it #gestione PRI span=1,0,0,ccs,hdb3,crc4,yellow bchan=1-15 # set this to 1-15,17-31 for E1 dchan=16 # set this to 16 for E1 bchan=17-31 # set this to 1-15,17-31 for E1 # Asterisk starts correctly, I see th 30 channels. Anyway I cannot put

please can someone send to me his files like zaptel & zapta if he si using TE110P thank you

Hola, tengo una tonteria que no me sale. Esta tablita esta ordenada de menor a mayor. Como hago para invertir el orden (de mayor a menor) ? Gracias     puerto                 visitas medias 3  Aldán-Hio             4.00 59    Tarifa                11.95 13 Camariñas           99.00 23 Cudillero            170.40 38   Mundaca        198.27 57   Suances            211.70 [[alternative HTML

I have a Digicom TE110p card installed in our exchange. I have compiled and installed libpri, zaptel and recompiled and installed asterisk. I have configured udev as I am running Fedora Core 3. The problem that I have is that when zaptel is not running everything works fine. However when I start zaptel (service start zaptel) then I can make normal calls ok but the 'Playback()'

Hi, thank you for last info. we've tried to use te110p but failed. We're quite surprised that cable wasn't included with the card as any documentation, at least on HW setup and installation, yet cable pinout for connection to PRI interfaces.... 1. We have followed instructions on your site and from Beronet guide, but card just keeps blinking and nothing happens (also no useful