thr3ads.net - asterisk users - [asterisk-users] Digium TE110P [Feb 2007]

If this information is useful, please help other people find it:
Share via:

Elman Efendiyev

2007-Feb-07 00:29 UTC

[asterisk-users] Digium TE110P

Helo,

I have problem with Digium TE110P connected to CISCO 3640 (port on
NM-HDV-2E1-60)  wth PRI E1 link. I use CISCO now for testing but when I
tried with real PBX problem was exactly same.
I have this messages in Asterisk conole and log sometimes:

NOTICE[1115] chan_zap.c: PRI got event: HDLC Abort (6) on Primary D-channel
of span 1

Usually 2-5 such messages in series, can be repeated after 10 minutes, or
after 30 minutes, or after 1-2 hours. I can't find any system when these
message occurs. This is ta test server with only Asterisk running, i left in
idle for couple hours (no calls at all), then put in under some traffic - no
difference. When I call trouth this * box and this messagw occurs I can hear
littlee click but not always. This wouldn't be a critical problem but over
some time (couple hors or day) I see this in log:

[Feb  7 01:01:10] NOTICE[614]: chan_zap.c:8431 pri_dchannel: PRI got event:
Alarm (4) on Primary D-channel of span 1
[Feb  7 01:01:10] WARNING[614]: chan_zap.c:2416 pri_find_dchan: No
D-channels available!  Using Primary channel 16 as D-channel anyway!
[Feb  7 01:01:10] WARNING[615]: chan_zap.c:6640 handle_init_event: Detected
alarm on channel 1: Yellow Alarm
[Feb  7 01:01:10] WARNING[615]: chan_zap.c:6640 handle_init_event: Detected
alarm on channel 2: Yellow Alarm
[Feb  7 01:01:10] WARNING[615]: chan_zap.c:6640 handle_init_event: Detected
alarm on channel 3: Yellow Alarm
[Feb  7 01:01:10] WARNING[615]: chan_zap.c:6640 handle_init_event: Detected
alarm on channel 4: Yellow Alarm
[Feb  7 01:01:10] WARNING[615]: chan_zap.c:6640 handle_init_event: Detected
alarm on channel 5: Yellow Alarm
[Feb  7 01:01:10] WARNING[615]: chan_zap.c:6640 handle_init_event: Detected
alarm on channel 6: Yellow Alarm
[Feb  7 01:01:10] WARNING[615]: chan_zap.c:6640 handle_init_event: Detected
alarm on channel 7: Yellow Alarm
[Feb  7 01:01:10] WARNING[615]: chan_zap.c:6640 handle_init_event: Detected
alarm on channel 8: Yellow Alarm
[Feb  7 01:01:10] WARNING[615]: chan_zap.c:6640 handle_init_event: Detected
alarm on channel 9: Yellow Alarm
[Feb  7 01:01:10] WARNING[615]: chan_zap.c:6640 handle_init_event: Detected
alarm on channel 10: Yellow Alarm
[Feb  7 01:01:10] WARNING[615]: chan_zap.c:6640 handle_init_event: Detected
alarm on channel 11: Yellow Alarm
[Feb  7 01:01:10] WARNING[615]: chan_zap.c:6640 handle_init_event: Detected
alarm on channel 12: Yellow Alarm
[Feb  7 01:01:10] WARNING[615]: chan_zap.c:6640 handle_init_event: Detected
alarm on channel 13: Yellow Alarm
[Feb  7 01:01:10] WARNING[615]: chan_zap.c:6640 handle_init_event: Detected
alarm on channel 14: Yellow Alarm
[Feb  7 01:01:10] WARNING[615]: chan_zap.c:6640 handle_init_event: Detected
alarm on channel 15: Yellow Alarm
[Feb  7 01:01:10] WARNING[615]: chan_zap.c:6640 handle_init_event: Detected
alarm on channel 17: Yellow Alarm
[Feb  7 01:01:10] WARNING[615]: chan_zap.c:6640 handle_init_event: Detected
alarm on channel 18: Yellow Alarm
[Feb  7 01:01:10] WARNING[615]: chan_zap.c:6640 handle_init_event: Detected
alarm on channel 19: Yellow Alarm
[Feb  7 01:01:10] WARNING[615]: chan_zap.c:6640 handle_init_event: Detected
alarm on channel 20: Yellow Alarm
[Feb  7 01:01:10] WARNING[615]: chan_zap.c:6640 handle_init_event: Detected
alarm on channel 21: Yellow Alarm
[Feb  7 01:01:10] WARNING[615]: chan_zap.c:6640 handle_init_event: Detected
alarm on channel 22: Yellow Alarm
[Feb  7 01:01:10] WARNING[615]: chan_zap.c:6640 handle_init_event: Detected
alarm on channel 23: Yellow Alarm
[Feb  7 01:01:10] WARNING[615]: chan_zap.c:6640 handle_init_event: Detected
alarm on channel 24: Yellow Alarm
[Feb  7 01:01:10] WARNING[615]: chan_zap.c:6640 handle_init_event: Detected
alarm on channel 25: Yellow Alarm
[Feb  7 01:01:10] WARNING[615]: chan_zap.c:6640 handle_init_event: Detected
alarm on channel 26: Yellow Alarm
[Feb  7 01:01:10] WARNING[615]: chan_zap.c:6640 handle_init_event: Detected
alarm on channel 27: Yellow Alarm
[Feb  7 01:01:10] WARNING[615]: chan_zap.c:6640 handle_init_event: Detected
alarm on channel 28: Yellow Alarm
[Feb  7 01:01:10] WARNING[615]: chan_zap.c:6640 handle_init_event: Detected
alarm on channel 29: Yellow Alarm
[Feb  7 01:01:10] WARNING[615]: chan_zap.c:6640 handle_init_event: Detected
alarm on channel 30: Yellow Alarm
[Feb  7 01:01:10] WARNING[615]: chan_zap.c:6640 handle_init_event: Detected
alarm on channel 31: Yellow Alarm
[Feb  7 01:01:10] NOTICE[614]: chan_zap.c:8431 pri_dchannel: PRI got event:
No more alarm (5) on Primary D-channel of span 1
[Feb  7 01:01:10] NOTICE[615]: chan_zap.c:6633 handle_init_event: Alarm
cleared on channel 1
[Feb  7 01:01:10] NOTICE[615]: chan_zap.c:6633 handle_init_event: Alarm
cleared on channel 2
[Feb  7 01:01:10] NOTICE[615]: chan_zap.c:6633 handle_init_event: Alarm
cleared on channel 3
[Feb  7 01:01:10] NOTICE[615]: chan_zap.c:6633 handle_init_event: Alarm
cleared on channel 4
[Feb  7 01:01:10] NOTICE[615]: chan_zap.c:6633 handle_init_event: Alarm
cleared on channel 5
[Feb  7 01:01:10] NOTICE[615]: chan_zap.c:6633 handle_init_event: Alarm
cleared on channel 6
[Feb  7 01:01:10] NOTICE[615]: chan_zap.c:6633 handle_init_event: Alarm
cleared on channel 7
[Feb  7 01:01:10] NOTICE[615]: chan_zap.c:6633 handle_init_event: Alarm
cleared on channel 8
[Feb  7 01:01:10] NOTICE[615]: chan_zap.c:6633 handle_init_event: Alarm
cleared on channel 9
[Feb  7 01:01:10] NOTICE[615]: chan_zap.c:6633 handle_init_event: Alarm
cleared on channel 10
[Feb  7 01:01:10] NOTICE[615]: chan_zap.c:6633 handle_init_event: Alarm
cleared on channel 11
[Feb  7 01:01:10] NOTICE[615]: chan_zap.c:6633 handle_init_event: Alarm
cleared on channel 12
[Feb  7 01:01:10] NOTICE[615]: chan_zap.c:6633 handle_init_event: Alarm
cleared on channel 13
[Feb  7 01:01:10] NOTICE[615]: chan_zap.c:6633 handle_init_event: Alarm
cleared on channel 14
[Feb  7 01:01:10] NOTICE[615]: chan_zap.c:6633 handle_init_event: Alarm
cleared on channel 15
[Feb  7 01:01:10] NOTICE[615]: chan_zap.c:6633 handle_init_event: Alarm
cleared on channel 17
[Feb  7 01:01:10] NOTICE[615]: chan_zap.c:6633 handle_init_event: Alarm
cleared on channel 18
[Feb  7 01:01:10] NOTICE[615]: chan_zap.c:6633 handle_init_event: Alarm
cleared on channel 19
[Feb  7 01:01:10] NOTICE[615]: chan_zap.c:6633 handle_init_event: Alarm
cleared on channel 20
[Feb  7 01:01:10] NOTICE[615]: chan_zap.c:6633 handle_init_event: Alarm
cleared on channel 21
[Feb  7 01:01:10] NOTICE[615]: chan_zap.c:6633 handle_init_event: Alarm
cleared on channel 22
[Feb  7 01:01:10] NOTICE[615]: chan_zap.c:6633 handle_init_event: Alarm
cleared on channel 23
[Feb  7 01:01:10] NOTICE[615]: chan_zap.c:6633 handle_init_event: Alarm
cleared on channel 24
[Feb  7 01:01:10] NOTICE[615]: chan_zap.c:6633 handle_init_event: Alarm
cleared on channel 25
[Feb  7 01:01:10] NOTICE[615]: chan_zap.c:6633 handle_init_event: Alarm
cleared on channel 26
[Feb  7 01:01:10] NOTICE[615]: chan_zap.c:6633 handle_init_event: Alarm
cleared on channel 27
[Feb  7 01:01:10] NOTICE[615]: chan_zap.c:6633 handle_init_event: Alarm
cleared on channel 28
[Feb  7 01:01:10] NOTICE[615]: chan_zap.c:6633 handle_init_event: Alarm
cleared on channel 29
[Feb  7 01:01:10] NOTICE[615]: chan_zap.c:6633 handle_init_event: Alarm
cleared on channel 30
[Feb  7 01:01:10] NOTICE[615]: chan_zap.c:6633 handle_init_event: Alarm
cleared on channel 31
  == Primary D-Channel on span 1 up

and ofcourse all calls are droped.

I searched wiki and maillists and found that this is a common problem with
TE110P, but I tried most known solutions without success. I changed
motherboard, CPU, etc.

My configs:

/etc/zaptel.conf:
loadzone = us
defaultzone=us
span=1,0,0,ccs,hdb3
bchan=1-15,17-31
dchan=16

/etc/asterisk/zapata.conf
[trunkgroups]

[channels]
context=default
group=1
signalling=pri_net
switchtype=euroisdn
resetinterval = never
channel=>1-15,17-31


CISCO config:

controller E1 2/1
 framing NO-CRC4
 pri-group timeslots 1-31

interface Serial2/1:15
 no ip address
 encapsulation hdlc
 isdn switch-type primary-net5
 isdn incoming-voice voice
 no cdp enable


More strange thing: when I changed master/slave (CISCO master and TE110P
slave) like this:

/etc/zaptel.conf:
loadzone = us
defaultzone=us
span=1,1,0,ccs,hdb3
bchan=1-15,17-31
dchan=16

/etc/asterisk/zapata.conf
[trunkgroups]

[channels]
context=default
group=1
signalling=pri_cpe
switchtype=euroisdn
resetinterval = never
channel=>1-15,17-31


CISCO config:

controller E1 2/1
 framing NO-CRC4
 clock source internal
 pri-group timeslots 1-31

interface Serial2/1:15
 no ip address
 encapsulation hdlc
 isdn switch-type primary-net5
 isdn protocol-emulate network
 isdn incoming-voice voice
 no cdp enable

I have continuously Yellow alarm messages, and zttool still thinks that
TE110p is master:

Current Alarms:     No alarms.
         ?    Sync Source:        Internally clocked
         ?    IRQ Misses:               0
         ?    Bipolar Viol:             0
         ?    Tx/Rx Levels:         0/  0
         ?    Total/Conf/Act:      31/ 31/  0

So I can't make TE110P slave at all....

Also I can't get 100% pseudo zap interface accuracy:
zaptel-1.4.0/zttest
Opened pseudo zap interface, measuring accuracy...
99.987793% 99.987793% 99.987793% 99.987793% 99.987793% 99.987793% 99.987793%
.....
99.987793% 99.987793% 99.987793% 99.987793% 99.987793% 99.987793% 99.987793%
99.987793%
--- Results after 46 passes ---
Best: 100.000000 -- Worst: 99.987793 -- Average: 99.988058
But when I run it for long (hour or more) worst can be 95....96%

I think this is a reason for above troubles but can't find a way to fix it.
Also I can't understand why TE110P can't be a slave...

Hardware:
Motherboard Intel SE-7210TP1-E with Gigabit Ethernet disabled in BIOS, using
100M ethernet (tried two other model motherboards, Intel and VIA)
Pention 4 HT 3.0GHz 800MHz FSB (tried Celeron 2.4GHz too)
IDE HDD with UDMA2 (hdparm -u1c1d1X66 /dev/hda)

Asterisk, libpri and zaptel versions 1.4.0 release, Linux 2.6.20 (tried
2.6.17 and 2.6.19)

I disabled all not needed devices on motherboard BIOS (even video) and
compiled only needed drivers in kernel, tried preemptable and
not-preemptable kernel, 100, 250 and 1000Hz timer.
Looks like I haven't IRQ problem:

cat /proc/interrupts
           CPU0
  0:     182503   IO-APIC-edge      timer
  1:          8   IO-APIC-edge      i8042
  2:          0    XT-PIC-XT        cascade
  8:          1   IO-APIC-edge      rtc
 12:          3   IO-APIC-edge      i8042
 14:       2989   IO-APIC-edge      ide0
 16:     725232   IO-APIC-fasteoi   wcte11xp
 17:       2233   IO-APIC-fasteoi   eth0
NMI:          0
LOC:     182461
ERR:          0
MIS:          0

lspci -v
00:00.0 Host bridge: Intel Corporation 82875P/E7210 Memory Controller Hub
(rev 02)
        Flags: bus master, fast devsel, latency 0
        Memory at fe800000 (32-bit, prefetchable) [size=4M]
        Capabilities: [e4] Vendor Specific Information

00:1c.0 PCI bridge: Intel Corporation 6300ESB 64-bit PCI-X Bridge (rev 02)
(prog-if 00 [Normal decode])
        Flags: bus master, 66MHz, fast devsel, latency 64
        Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
        Capabilities: [50] PCI-X bridge device

00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 0a) (prog-if 00
[Normal decode])
        Flags: bus master, fast devsel, latency 0
        Bus: primary=00, secondary=02, subordinate=02, sec-latency=32
        I/O behind bridge: 0000e000-0000efff
        Memory behind bridge: fe600000-fe6fffff

00:1f.0 ISA bridge: Intel Corporation 6300ESB LPC Interface Controller (rev
02)
        Flags: bus master, medium devsel, latency 0

00:1f.1 IDE interface: Intel Corporation 6300ESB PATA Storage Controller
(rev 02) (prog-if 8a [Master SecP PriP])
        Flags: bus master, medium devsel, latency 0, IRQ 18
        I/O ports at 01f0 [size=8]
        I/O ports at 03f4 [size=1]
        I/O ports at 0170 [size=8]
        I/O ports at 0374 [size=1]
        I/O ports at fc00 [size=16]
        Memory at 50000000 (32-bit, non-prefetchable) [size=1K]

00:1f.3 SMBus: Intel Corporation 6300ESB SMBus Controller (rev 02)
        Flags: medium devsel, IRQ 17
        I/O ports at 0400 [size=32]

02:01.0 Ethernet controller: Intel Corporation 82557/8/9 [Ethernet Pro 100]
(rev 10)
        Subsystem: Intel Corporation Unknown device 342f
        Flags: bus master, medium devsel, latency 64, IRQ 17
        Memory at fe6fe000 (32-bit, non-prefetchable) [size=4K]
        I/O ports at ec00 [size=64]
        Memory at fe6a0000 (32-bit, non-prefetchable) [size=128K]
        Capabilities: [dc] Power Management version 2

02:02.0 Network controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN
interface
        Subsystem: Unknown device 795e:0001
        Flags: bus master, medium devsel, latency 64, IRQ 16
        I/O ports at e800 [size=256]
        Memory at fe6fd000 (32-bit, non-prefetchable) [size=4K]
        Capabilities: [40] Power Management version 2

lspci -vb
00:00.0 Host bridge: Intel Corporation 82875P/E7210 Memory Controller Hub
(rev 02)
        Flags: bus master, fast devsel, latency 0
        Memory at fe800000 (32-bit, prefetchable)
        Capabilities: [e4] Vendor Specific Information

00:1c.0 PCI bridge: Intel Corporation 6300ESB 64-bit PCI-X Bridge (rev 02)
(prog-if 00 [Normal decode])
        Flags: bus master, 66MHz, fast devsel, latency 64
        Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
        Capabilities: [50] PCI-X bridge device

00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 0a) (prog-if 00
[Normal decode])
        Flags: bus master, fast devsel, latency 0
        Bus: primary=00, secondary=02, subordinate=02, sec-latency=32
        I/O behind bridge: 0000e000-0000efff
        Memory behind bridge: fe600000-fe6fffff

00:1f.0 ISA bridge: Intel Corporation 6300ESB LPC Interface Controller (rev
02)
        Flags: bus master, medium devsel, latency 0

00:1f.1 IDE interface: Intel Corporation 6300ESB PATA Storage Controller
(rev 02) (prog-if 8a [Master SecP PriP])
        Flags: bus master, medium devsel, latency 0
        I/O ports at <unassigned>
        I/O ports at <unassigned>
        I/O ports at <unassigned>
        I/O ports at <unassigned>
        I/O ports at fc00
        Memory at 50000000 (32-bit, non-prefetchable)

00:1f.3 SMBus: Intel Corporation 6300ESB SMBus Controller (rev 02)
        Flags: medium devsel, IRQ 11
        I/O ports at 0400

02:01.0 Ethernet controller: Intel Corporation 82557/8/9 [Ethernet Pro 100]
(rev 10)
        Subsystem: Intel Corporation Unknown device 342f
        Flags: bus master, medium devsel, latency 64, IRQ 11
        Memory at fe6fe000 (32-bit, non-prefetchable)
        I/O ports at ec00
        Memory at fe6a0000 (32-bit, non-prefetchable)
        Capabilities: [dc] Power Management version 2

02:02.0 Network controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN
interface
        Subsystem: Unknown device 795e:0001
        Flags: bus master, medium devsel, latency 64, IRQ 9
        I/O ports at e800
        Memory at fe6fd000 (32-bit, non-prefetchable)
        Capabilities: [40] Power Management version 2

I appreciate any ideas.

Thank you.

--
Sincerely,
Elman Efendiyev

rivoli.durand

2007-Feb-16 06:52 UTC

head link

[asterisk-users] Digium TE110P

Hi

I am currently installing a TE110P.
SUSE10
The zttest test result is : average 99.9991%.

My server : processor Intel? Celeron? D 330, 2.66 GHz, cache
256 Ko, FSB 533 MHz , 1G RAM.

Hope it can help.

Now I have a question to TE110P users :
The card is physically plugged, modprobe, ztcfg ok etc ...
There is a red led blinking.

The question is : should this led provide a green continuous
light or is it correct to have a red blinking light ?

Thanks in advance

Olivier












Envoyez vos cartes de voeux depuis www.laposte.net 
Elles seront ensuite distribu?es par le facteur : pratique et malin !

demuel@thephinix.org

2007-Feb-16 07:05 UTC

head link

[asterisk-users] Digium TE110P

Hello,

Hmm, you are like me eons ago doing stuff on TE110P. Anyway, consider the
following questions:

1. Is the jumper for that card set to E1 or T1?
2. Do you have an E1 or T1 link there?


When you have an E1/T1 line there at your disposal, insert it in the slot. In
either case, the
green light should be steady and there will be no red light. Actually, the red
light indicates
that it ask for an active E1/T1 link.

Hope it helps you.


Regards,
Demuel
> Hi
>
> I am currently installing a TE110P.
> SUSE10
> The zttest test result is : average 99.9991%.
>
> My server : processor Intel? Celeron? D 330, 2.66 GHz, cache
> 256 Ko, FSB 533 MHz , 1G RAM.
>
> Hope it can help.
>
> Now I have a question to TE110P users :
> The card is physically plugged, modprobe, ztcfg ok etc ...
> There is a red led blinking.
>
> The question is : should this led provide a green continuous
> light or is it correct to have a red blinking light ?
>
> Thanks in advance
>
> Olivier
>
>
>
>
>
>
>
>
>
>
>
>
> Envoyez vos cartes de voeux depuis www.laposte.net
> Elles seront ensuite distribu?es par le facteur : pratique et malin !
>
> _______________________________________________
> --Bandwidth and Colocation provided by Easynews.com --
>
> asterisk-users mailing list
> To UNSUBSCRIBE or update options visit:
>    http://lists.digium.com/mailman/listinfo/asterisk-users
>

rivoli.durand

2007-Feb-16 07:32 UTC

head link

[asterisk-users] Digium TE110P

Hi Demuel

Thanks, it definitely helps a lot.

I forgot to mention that I worked out the jumper thing.

So, you give the explanation that is : as there is no E1/T1
connected to the card, the card is somewhat saying that it is
waiting for a link.

In this regard, it behaves differently from an analogic one,
like the TDM400P, which shows a constant green light as soon
as the driver is being loaded, even if there is no analogic
link connected to the card. I was expecting the same behaviour
from the TE110P.

Thanks again,  

Olivier

Envoyez vos cartes de voeux depuis www.laposte.net 
Elles seront ensuite distribu?es par le facteur : pratique et malin !

demuel@thephinix.org

2007-Feb-16 07:36 UTC

head link

[asterisk-users] Digium TE110P

Again, you need a E1/T1 link for that card and you need to set out the jumper
either for T1 or E1
link. Since you are in Europe, the jumper settings should be for E1.

This card is different from the TDM400P family.

Regards,
Demuel
> Hi Demuel
>
> Thanks, it definitely helps a lot.
>
> I forgot to mention that I worked out the jumper thing.
>
> So, you give the explanation that is : as there is no E1/T1
> connected to the card, the card is somewhat saying that it is
> waiting for a link.
>
> In this regard, it behaves differently from an analogic one,
> like the TDM400P, which shows a constant green light as soon
> as the driver is being loaded, even if there is no analogic
> link connected to the card. I was expecting the same behaviour
> from the TE110P.
>
> Thanks again,
>
> Olivier
>
> Envoyez vos cartes de voeux depuis www.laposte.net
> Elles seront ensuite distribu?es par le facteur : pratique et malin !
>
> _______________________________________________
> --Bandwidth and Colocation provided by Easynews.com --
>
> asterisk-users mailing list
> To UNSUBSCRIBE or update options visit:
>    http://lists.digium.com/mailman/listinfo/asterisk-users
>

Elman Efendiyev

2007-Feb-16 08:56 UTC

head link

[asterisk-users] Digium TE110P

Hi,

Thanks for info but could You please tell an exact mobel name of your
motherboard?

About led - when PRI cables not connected to TE100P or when there is a
problem no physical level whth PRI led should be red blinking.
When PRI link connecteg successfully led should provide a green continuous
light

--
Sincerely,
Elman Efendiyev
PROTECH INC.

-----Original Message-----
From: asterisk-users-bounces@lists.digium.com
[mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of rivoli.durand
Sent: Friday, 16 February, 2007 15:52
To: asterisk-users
Subject: [asterisk-users] Digium TE110P 

Hi

I am currently installing a TE110P.
SUSE10
The zttest test result is : average 99.9991%.

My server : processor Intel? Celeron? D 330, 2.66 GHz, cache
256 Ko, FSB 533 MHz , 1G RAM.

Hope it can help.

Now I have a question to TE110P users :
The card is physically plugged, modprobe, ztcfg ok etc ...
There is a red led blinking.

The question is : should this led provide a green continuous
light or is it correct to have a red blinking light ?

Thanks in advance

Olivier












Envoyez vos cartes de voeux depuis www.laposte.net 
Elles seront ensuite distribu?es par le facteur : pratique et malin !

_______________________________________________
--Bandwidth and Colocation provided by Easynews.com --

asterisk-users mailing list
To UNSUBSCRIBE or update options visit:
   http://lists.digium.com/mailman/listinfo/asterisk-users

Carlos Chavez

2007-Feb-21 10:21 UTC

head link

[asterisk-users] Digium TE110P

On Wed, 2007-02-21 at 16:14 +0000, younss azzayani
wrote:> Hi,
> thank You,
> when i run "zttool i get
> ************************************
>  Alarms          Span                                               ?
>    ?     UNCONFIGURED    Digium Wildcard TE110P T1/E1 Card 0             ? 
?
>    ?     UNCONFIGURED    ZTDUMMY/1 1                                     ? 
?
>    ?                                                                     ? 
?
>    ?                                                                     ? 
?
>    ?                                                                     # 
?
>    ?                                                                     ? 
?
>    ?                                                                     ? 
?
>    ?                                                                     ? 
?
>    ?                                                                     ? 
?
>    ?                                                                     ? 
?
>    ?                                                                       
?
>    ?                                                                       
?
>    ?          ??????????                              ????????             
?
>    ?          ? Select ?                              ? Quit ?             
?
>    ?          ??????????                              ????????             
?
>    ?                                                                       
?
>    ??????????????????????????????????????????????????????????
> *************************************************
	What is you /etc/zaptel.conf configuration like?  Have you defined the
span?

-- 
Telecomunicaciones Abiertas de Mexico S.A. de C.V.
Carlos Ch?vez Prats
Director de Tecnolog?a
+52-55-91169161 ext 2001
-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 189 bytes
Desc: This is a digitally signed message part
Url :
http://lists.digium.com/pipermail/asterisk-users/attachments/20070221/238f2999/attachment-0001.pgp

younss azzayani

2007-Feb-21 17:46 UTC

head link

[asterisk-users] Digium TE110P

this is my zaptel.conf::
[root@asterisk1 ~]# cat /etc/zaptel.conf
# Autogenerated by /usr/local/sbin/genzaptelconf -- do not hand edit
# Zaptel Configuration File
#
# This file is parsed by the Zaptel Configurator, ztcfg
#

# It must be in the module loading order


# Span 1: WCT1/0 "Digium Wildcard TE110P T1/E1 Card 0"
# channel 1, WCT1, unhandled for now
# channel 2, WCT1, unhandled for now
# channel 3, WCT1, unhandled for now
# channel 4, WCT1, unhandled for now
# channel 5, WCT1, unhandled for now
# channel 6, WCT1, unhandled for now
# channel 7, WCT1, unhandled for now
# channel 8, WCT1, unhandled for now
# channel 9, WCT1, unhandled for now
# channel 10, WCT1, unhandled for now
# channel 11, WCT1, unhandled for now
# channel 12, WCT1, unhandled for now
# channel 13, WCT1, unhandled for now
# channel 14, WCT1, unhandled for now
# channel 15, WCT1, unhandled for now
# channel 16, WCT1, unhandled for now
# channel 17, WCT1, unhandled for now
# channel 18, WCT1, unhandled for now
# channel 19, WCT1, unhandled for now
# channel 20, WCT1, unhandled for now
# channel 21, WCT1, unhandled for now
# channel 22, WCT1, unhandled for now
# channel 23, WCT1, unhandled for now
# channel 24, WCT1, unhandled for now
# channel 25, WCT1, unhandled for now
# channel 26, WCT1, unhandled for now
# channel 27, WCT1, unhandled for now
# channel 28, WCT1, unhandled for now
# channel 29, WCT1, unhandled for now
# channel 30, WCT1, unhandled for now
# channel 31, WCT1, unhandled for now

# Span 2: ZTDUMMY/1 "ZTDUMMY/1 1"

# Global data

loadzone        = us
defaultzone     = us

Paul Hales

2007-Feb-21 17:58 UTC

head link

[asterisk-users] Digium TE110P

genzaptel is _not_ your friend when setting up E1.

PaulH

On Thu, 2007-02-22 at 00:46 +0000, younss azzayani
wrote:> this is my zaptel.conf::
> [root@asterisk1 ~]# cat /etc/zaptel.conf
> # Autogenerated by /usr/local/sbin/genzaptelconf -- do not hand edit
> # Zaptel Configuration File
> #
> # This file is parsed by the Zaptel Configurator, ztcfg
> #
> 
> # It must be in the module loading order
> 
> 
> # Span 1: WCT1/0 "Digium Wildcard TE110P T1/E1 Card 0"
> # channel 1, WCT1, unhandled for now
> # channel 2, WCT1, unhandled for now
> # channel 3, WCT1, unhandled for now
> # channel 4, WCT1, unhandled for now
> # channel 5, WCT1, unhandled for now
> # channel 6, WCT1, unhandled for now
> # channel 7, WCT1, unhandled for now
> # channel 8, WCT1, unhandled for now
> # channel 9, WCT1, unhandled for now
> # channel 10, WCT1, unhandled for now
> # channel 11, WCT1, unhandled for now
> # channel 12, WCT1, unhandled for now
> # channel 13, WCT1, unhandled for now
> # channel 14, WCT1, unhandled for now
> # channel 15, WCT1, unhandled for now
> # channel 16, WCT1, unhandled for now
> # channel 17, WCT1, unhandled for now
> # channel 18, WCT1, unhandled for now
> # channel 19, WCT1, unhandled for now
> # channel 20, WCT1, unhandled for now
> # channel 21, WCT1, unhandled for now
> # channel 22, WCT1, unhandled for now
> # channel 23, WCT1, unhandled for now
> # channel 24, WCT1, unhandled for now
> # channel 25, WCT1, unhandled for now
> # channel 26, WCT1, unhandled for now
> # channel 27, WCT1, unhandled for now
> # channel 28, WCT1, unhandled for now
> # channel 29, WCT1, unhandled for now
> # channel 30, WCT1, unhandled for now
> # channel 31, WCT1, unhandled for now
> 
> # Span 2: ZTDUMMY/1 "ZTDUMMY/1 1"
> 
> # Global data
> 
> loadzone        = us
> defaultzone     = us
> _______________________________________________
> --Bandwidth and Colocation provided by Easynews.com --
> 
> asterisk-users mailing list
> To UNSUBSCRIBE or update options visit:
>    http://lists.digium.com/mailman/listinfo/asterisk-users

younss azzayani

2007-Feb-22 03:30 UTC

head link

[asterisk-users] Digium TE110P

"genzaptelconf" you mean?


2007/2/22, Paul Hales <pdhales@optusnet.com.au>:>
> genzaptel is _not_ your friend when setting up E1.
>
> PaulH
>
> On Thu, 2007-02-22 at 00:46 +0000, younss azzayani wrote:
> > this is my zaptel.conf::
> > [root@asterisk1 ~]# cat /etc/zaptel.conf
> > # Autogenerated by /usr/local/sbin/genzaptelconf -- do not hand edit
> > # Zaptel Configuration File
> > #
> > # This file is parsed by the Zaptel Configurator, ztcfg
> > #
> >
> > # It must be in the module loading order
> >
> >
> > # Span 1: WCT1/0 "Digium Wildcard TE110P T1/E1 Card 0"
> > # channel 1, WCT1, unhandled for now
> > # channel 2, WCT1, unhandled for now
> > # channel 3, WCT1, unhandled for now
> > # channel 4, WCT1, unhandled for now
> > # channel 5, WCT1, unhandled for now
> > # channel 6, WCT1, unhandled for now
> > # channel 7, WCT1, unhandled for now
> > # channel 8, WCT1, unhandled for now
> > # channel 9, WCT1, unhandled for now
> > # channel 10, WCT1, unhandled for now
> > # channel 11, WCT1, unhandled for now
> > # channel 12, WCT1, unhandled for now
> > # channel 13, WCT1, unhandled for now
> > # channel 14, WCT1, unhandled for now
> > # channel 15, WCT1, unhandled for now
> > # channel 16, WCT1, unhandled for now
> > # channel 17, WCT1, unhandled for now
> > # channel 18, WCT1, unhandled for now
> > # channel 19, WCT1, unhandled for now
> > # channel 20, WCT1, unhandled for now
> > # channel 21, WCT1, unhandled for now
> > # channel 22, WCT1, unhandled for now
> > # channel 23, WCT1, unhandled for now
> > # channel 24, WCT1, unhandled for now
> > # channel 25, WCT1, unhandled for now
> > # channel 26, WCT1, unhandled for now
> > # channel 27, WCT1, unhandled for now
> > # channel 28, WCT1, unhandled for now
> > # channel 29, WCT1, unhandled for now
> > # channel 30, WCT1, unhandled for now
> > # channel 31, WCT1, unhandled for now
> >
> > # Span 2: ZTDUMMY/1 "ZTDUMMY/1 1"
> >
> > # Global data
> >
> > loadzone        = us
> > defaultzone     = us
> > _______________________________________________
> > --Bandwidth and Colocation provided by Easynews.com --
> >
> > asterisk-users mailing list
> > To UNSUBSCRIBE or update options visit:
> >    http://lists.digium.com/mailman/listinfo/asterisk-users
>
> _______________________________________________
> --Bandwidth and Colocation provided by Easynews.com --
>
> asterisk-users mailing list
> To UNSUBSCRIBE or update options visit:
>    http://lists.digium.com/mailman/listinfo/asterisk-users
>

Seemingly Similar Threads

Search for more apparently analagous threads

asterisk users - Feb 2007 - Digium TE110P

[asterisk-users] Digium TE110P

[asterisk-users] Digium TE110P

[asterisk-users] Digium TE110P

[asterisk-users] Digium TE110P

[asterisk-users] Digium TE110P

[asterisk-users] Digium TE110P

[asterisk-users] Digium TE110P

[asterisk-users] Digium TE110P

[asterisk-users] Digium TE110P

[asterisk-users] Digium TE110P

Seemingly Similar Threads