similar to: Wildcard Testing

Displaying 20 results from an estimated 1000 matches similar to: "Wildcard Testing"

2005 May 06
0
Wildcard TE110p initial setup
I'm not 'overly' new to asterisk, but I am very new to the Digium card / Telco aspect of it. I was able to get a TE110p card, installed.. and hooked a t1 up to it. I'm using zttool to just look at 'some' output. Here is what it looks like when I just load it up: Current Alarms: No alarms. ? ? ? ? Sync Source:
2003 Jul 14
2
insmod wcfxo failed ( b8zs, esf, wink start is what I'm trying to do.)
Thanks in advance root@asterisk01:~# modprobe wcfxo /lib/modules/2.4.20/misc/wcfxo.o: init_module: No such device /lib/modules/2.4.20/misc/wcfxo.o: Hint: insmod errors can be caused by incorrect module parameters, including invalid IO or IRQ parameters. You may find more information in syslog or the output from dmesg /lib/modules/2.4.20/misc/wcfxo.o: insmod /lib/modules/2.4.20/misc/wcfxo.o
2006 Jun 14
0
FW: Issue in configuring TDM400P
Hi, I have installed a TDM400P in a PC which runs RedHat Linux 3.2.2-5. There is an FXS module connected to the first slot of TDM400P and an FXO module connected to the fourth slot. This card is detected by the operationg system, which I was able to make sure using the output of lspci command. I modified the configuration files zaptel.conf, zapata.conf and extensions.conf. When I execute the
2008 Apr 22
0
Bip viol. in E1 cards
Hi all.. I`m with a problem in some E1 cards. The value of Bipolar Viol is too big, and some times the link seems well, but isn`t work correctly, like as if the link is down. Normally, I use to stop asterisk, remove the modules from my card, use modprove to set up they again, and start asterisk, and it come to work, but in some times I have to reboot the server, and then the value of
2004 Jul 09
3
tc filter + bridging + htb -- works only if ip_forward = 0
I thought that the below email would be of interest to LARTC readers. I wasted quite a bit of time tracking down this "feature" (bug?). Any comments that shed light on this would be appreciated. In short, "tc filter" + htb + bridging works only with ip_forward off. Andrew Athan ----------------------------------------------------------------------- All: It seems that
2009 Mar 27
4
Help: RED alarm on Wildcard TE122 card
Hi, I have been trying to get a Wildcard TE122 card running here the last couple of days. libpri and zaptel are all installed and configured to E1 specs. The jumper on the card is on, so configured for E1 (I'm in Norway). When running zttool, I get 'Alarms: RED' on the single card installed. Other information in zttool: Current alarms: Red Alarm Sync source: Internally clocked
2005 Aug 04
1
HELP! X100P IRQ conflict w/ USB
PC: HP Vetra VL400 Mainbood: Intel815 BIOS: Phonix 4.0 release 6.0 OS: REDHAT 9.0 I installed the X100P in PCI slot 2 and disable the USB port, serial-port and parallel-port in BIOS. I can't found the X100P card in " cat interrupts" But I can found the card in the "cat ioports" use "lspci" I found the X100Pcard use the interrupts 11 too. Who can help me to solve
2004 Aug 25
1
2x HFC ISDN Cards - SuSE 9.1 - Problems with making calls
Hello everyone, I bought 2 HFC-ISDN Cards and want to run the first card in NT-Mode an the second one in TE-Mode. Everything looks ok under SuSE 9.1, but I can't dial out. I removed one card, for testing purposes and want to run this one card in TE-Mode. I only want to make a call with my Grandstream BT-101 over Asterisk via ISDN. When I try to make a call I get: ---------------------
2008 Jan 07
0
[Asterisk 1.2 + TDM FXO] Incoming call not detected
Hi On an old IBM Netvista thinclient, the TDM card doesn't detect incoming calls, although the card seems to be detected, and correctly configured: pbx asterisk # lspci 00:03.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface # cat /etc/zaptel.conf fxsks=1 loadzone=fr defaultzone=fr # ztcfg -vv Zaptel Configuration ====================== Channel map: Channel
2009 Dec 24
0
X100P clone card problem
Hi, I have problem with X100P clone card.I can not force it to work under Asterisk 1.4.27.1 and DAHDI Version: 2.2.0.2. I looked over and over on configuration and could not see any mistakes. Here are relevant configuration files. /etc/dahdi/system.conf > fxsks=1 > echocanceller=mg2,1 > loadzone = hu > defaultzone = hu > dahdi_tool > OK Wildcard X100P
2007 May 02
0
ZAP Error: Unable to create channel of type 'Zap'
Hi Group, I have a problem with my FXO interface. It seems that asterisk cannot see any configured channels, only pseudo. Pls see the error and my config below. Rgrds Markus ----- May 2 15:09:00 NOTICE[17327]: app_dial.c:1010 dial_exec_full: Unable to create channel of type 'Zap' (cause 0 - Unknown) == Everyone is busy/congested at this time (1:0/0/1) == Auto fallthrough, channel
2007 Feb 09
1
Samba Domain Member Server -- tdbsam/winbind/idmap_rid -- file ownership ?
I have just struggled to implement a Samba Domain Server, and have some remaining issues. I have a Samba PDC using tdbsam, managing a domain called RHEA. I have (finally) configured a new Samba Domain Server (AUREUS) using winbind and idmap_rid. When I am logged in to RHEA as user GMCH I can access a TMP share on AUREUS (at last). Running 'getent passwd' I get (inter alia):
2008 Feb 20
0
Unable to create channel of type 'Zap' with ecmg2 and kernel 2.6.23
Hi, I have a working Asterisk 1.2 server on kernel 2.6.22 with the OSLEC echo canceller on a Digium PRI card. I recently switched to kernel 2.6.23 with the MG2 echo canceller (nothing else changed). Each time I try to establish a call on the PRI line I get a congestion signal. in /var/log/asterisk/full: Feb 20 08:09:43 VERBOSE[10657] logger.c: -- Executing
2003 Apr 04
0
How does UDMA mode get set?
Hi all, I have been tracking -STABLE on one of my home machines for a little while, now and noticed something the other day. I was given this system, and I have only run FreeBSD-STABLE on it. The motherboard is a Supermicro370SWD with an Intel 810 "Whitney" chipset (82810DC100 GMCH + 82801AA ICH). The docs say that there is support for UDMA66, but FreeBSD reports that the drive is
2010 Aug 10
1
PRI D-channel bouncing
I need some help getting a system running for one of my company's plants. I am running AsteriskNow 1.7 with Asterisk 1.6.2.10 and FreePBX 2.8.0.2. My D-Channel keeps bouncing. The telecom tech told me he thought that I might be using the wrong sync source, and I think I might have been, but I changed DAHDI system.conf to "span=1,1,0,ESF,B8ZS" (from
2003 Jun 30
1
T1 slips/BPVs clarifications (was: Help! Problems talking to upstream switch)
Just some clarification here. On Monday, June 30, 2003 12:04 AM, Steven Critchfield [SMTP:critch@basesys.com] wrote: > > As for slips and bipolar violations... > T1s are just high speed serial lines. A sleep is when you loose sync > with the far side and when you see a 1 come across the line, you may > not > know which bit it was for. A slip is when one end of the circuit is
2003 Jul 29
0
IRQ Misses?
Hi, One of my pbx's seems to be having some new issues. crackling interference on the zap channels running through the channel bank, and I noticed that these happen when I hit an "irq miss" in zttool: Current Alarms: No alarms. Sync Source: Digium Wildcard T100P T1/PRI C IRQ Misses: 82695 Bipolar Viol: 0 Tx/Rx Levels: 0/8 3 Total/Conf/Act:
2008 Feb 25
1
DTMF tone crashes server (Asterisk 1.4.18 with Digium TE120P)
Hi, I've been playing with a TE120P on Asterisk 1.4.18 with zaptel 1.4.9 and I've ran into an issue. After a call placed any DTMF tone causes the server to lock up entirely. Calls placed work just fine (except for a problem with echo cancellation). The phone registered to the server is a Linksys SPA-942. I am seeing in zttool some IRQ misses, but it never seems to go above 74 (below).
2008 Jul 21
1
merging violations.ignore.d/logcheck-* into ignore.d.*/*
Hi guys, now that violations.d/logcheck is empty, violations.ignore.d/logcheck-* are useless and many messages that were previously elevated and filtered there now turn up as system events. Thus, I went ahead and merged violations.ignore.d/logcheck-* into ignore.d.*/* in the viol-merge branch. http://git.debian.org/?p=logcheck/logcheck.git;a=shortlog;h=refs/heads/viol-merge Unless I hear
2005 Aug 12
0
ZapHFC E1 PRI (cwain)
Hello, I've got a Junghanns ZapHFC E1 PRI Card (cwain) and this driver writes very much messages into /var/log/messages like the following: --- snip --- Aug 2 17:58:02 asterisk1 kernel: cwain: card 1 RX [ 0x2 0x1 0x1 0x37 0x90 0xc3 ] 6 bytes Aug 2 17:58:02 asterisk1 kernel: cwain: card 1 TX [ 0x2 0x1 0x1 0xef ] Aug 2 17:58:02 asterisk1 kernel: ztx 4 bytes Aug 2 17:58:12 asterisk1