PC: HP Vetra VL400
Mainbood: Intel815
BIOS: Phonix 4.0 release 6.0
OS: REDHAT 9.0
I installed the X100P in PCI slot 2 and disable the USB port, serial-port
and parallel-port in BIOS.
I can't found the X100P card in " cat interrupts"
But I can found the card in the "cat ioports"
use "lspci" I found the X100Pcard use the interrupts 11 too. Who can
help me to solve this problem?
-----------------------------------------------
[root@qhserver proc]# cat interrupts
CPU0
0: 28561 XT-PIC timer
1: 6 XT-PIC keyboard
2: 0 XT-PIC cascade
5: 2954 XT-PIC eth0
8: 1 XT-PIC rtc
11: 0 XT-PIC usb-uhci
12: 29 XT-PIC PS/2 Mouse
14: 7199 XT-PIC ide0
15: 1 XT-PIC ide1
NMI: 0
ERR: 0
-------------------------------------------------
-------------------------------------------------
[root@qhserver proc]# cat ioports
0000-001f : dma1
0020-003f : pic1
0040-005f : timer
0060-006f : keyboard
0070-007f : rtc
0080-008f : dma page reg
00a0-00bf : pic2
00c0-00df : dma2
00f0-00ff : fpu
0170-0177 : ide1
01f0-01f7 : ide0
0376-0376 : ide1
0378-037a : parport0
037b-037f : parport0
03c0-03df : vga+
03f6-03f6 : ide0
0cf8-0cff : PCI conf1
1800-180f : Intel Corp. 82801AA IDE
1800-1807 : ide0
1808-180f : ide1
1810-181f : Intel Corp. 82801AA SMBus
1820-183f : Intel Corp. 82801AA USB
1820-183f : usb-uhci
2000-20ff : Tiger Jet Network Inc. Model 300 128k
2400-247f : 3Com Corporation 3c905C-TX/TX-M [Tornado]
2400-247f : 01:04.0
------------------------------------------------------
--------------------------------------------------------------------------------
[root@qhserver sbin]# ./lspci -vvv
00:00.0 Host bridge: Intel Corp. 82815 815 Chipset Host Bridge and Memory Contr)
Subsystem: Intel Corp. 82815 815 Chipset Host Bridge and Memory Controlb
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Ste-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort--
Latency: 0
Capabilities: [88] #09 [f104]
00:02.0 VGA compatible controller: Intel Corp. 82815 CGC [Chipset Graphics Cont)
Subsystem: Hewlett-Packard Company: Unknown device 1245
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Ste-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbor-
Latency: 0
Interrupt: pin A routed to IRQ 10
Region 0: Memory at f0000000 (32-bit, prefetchable) [size=64M]
Region 1: Memory at ec000000 (32-bit, non-prefetchable) [size=512K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3ho)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:1e.0 PCI bridge: Intel Corp. 82801AA PCI Bridge (rev 02) (prog-if 00 [Normal)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Ste-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort--
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
I/O behind bridge: 00002000-00002fff
Memory behind bridge: ec100000-ec1fffff
Prefetchable memory behind bridge: fff00000-000fffff
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
00:1f.0 ISA bridge: Intel Corp. 82801AA ISA Bridge (LPC) (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Ste-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbor-
Latency: 0
00:1f.1 IDE interface: Intel Corp. 82801AA IDE (rev 02) (prog-if 80 [Master])
Subsystem: Intel Corp. 82801AA IDE
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Ste-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbor-
Latency: 0
Region 4: I/O ports at 1800 [size=16]
00:1f.2 USB Controller: Intel Corp. 82801AA USB (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corp. 82801AA USB
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Ste-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbor-
Latency: 0
Interrupt: pin D routed to IRQ 11
Region 4: I/O ports at 1820 [size=32]
00:1f.3 SMBus: Intel Corp. 82801AA SMBus (rev 02)
Subsystem: Intel Corp. 82801AA SMBus
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Ste-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbor-
Interrupt: pin B routed to IRQ 9
Region 4: I/O ports at 1810 [size=16]
01:01.0 Communication controller: Tiger Jet Network Inc. Intel 537
Subsystem: Unknown device 8085:0003
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Ste-
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Ste-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbor-
Latency: 64 (250ns min, 32000ns max)
Interrupt: pin A routed to IRQ 5
Region 0: I/O ports at 2000 [size=256]
Region 1: Memory at ec100000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI+ D1- D2+ AuxCurrent=55mA PME(D0+,D1-,D2+,D3h)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:04.0 Ethernet controller: 3Com Corporation 3c905C-TX/TX-M [Tornado] (rev 78)
Subsystem: Hewlett-Packard Company: Unknown device 1246
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Ste-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbor-
Latency: 80 (2500ns min, 2500ns max), cache line size 08
Interrupt: pin A routed to IRQ 5
Region 0: I/O ports at 2400 [size=128]
Region 1: Memory at ec101000 (32-bit, non-prefetchable) [size=128]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3ho)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
-------------------------------------------------------------------------------------
Have you loaded the zaptel drivers yet? Until you load the wcfxo module you
will see nothing in /proc/interrupts.
Cheers,
Peter
-----Original Message-----
From: asterisk-users-bounces@lists.digium.com
[mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of 163
Sent: Friday, 5 August 2005 12:35 PM
To: asterisk-users@lists.digium.com
Subject: [Asterisk-Users] HELP! X100P IRQ conflict w/ USB
PC: HP Vetra VL400
Mainbood: Intel815
BIOS: Phonix 4.0 release 6.0
OS: REDHAT 9.0
I installed the X100P in PCI slot 2 and disable the USB port, serial-port
and parallel-port in BIOS. I can't found the X100P card in " cat
interrupts"
But I can found the card in the "cat ioports" use "lspci" I
found the
X100Pcard use the interrupts 11 too. Who can help me to solve this problem?
-----------------------------------------------
[root@qhserver proc]# cat interrupts
CPU0
0: 28561 XT-PIC timer
1: 6 XT-PIC keyboard
2: 0 XT-PIC cascade
5: 2954 XT-PIC eth0
8: 1 XT-PIC rtc
11: 0 XT-PIC usb-uhci
12: 29 XT-PIC PS/2 Mouse
14: 7199 XT-PIC ide0
15: 1 XT-PIC ide1
NMI: 0
ERR: 0
-------------------------------------------------
-------------------------------------------------
[root@qhserver proc]# cat ioports
0000-001f : dma1
0020-003f : pic1
0040-005f : timer
0060-006f : keyboard
0070-007f : rtc
0080-008f : dma page reg
00a0-00bf : pic2
00c0-00df : dma2
00f0-00ff : fpu
0170-0177 : ide1
01f0-01f7 : ide0
0376-0376 : ide1
0378-037a : parport0
037b-037f : parport0
03c0-03df : vga+
03f6-03f6 : ide0
0cf8-0cff : PCI conf1
1800-180f : Intel Corp. 82801AA IDE
1800-1807 : ide0
1808-180f : ide1
1810-181f : Intel Corp. 82801AA SMBus
1820-183f : Intel Corp. 82801AA USB
1820-183f : usb-uhci
2000-20ff : Tiger Jet Network Inc. Model 300 128k
2400-247f : 3Com Corporation 3c905C-TX/TX-M [Tornado]
2400-247f : 01:04.0
------------------------------------------------------
----------------------------------------------------------------------------
----
[root@qhserver sbin]# ./lspci -vvv
00:00.0 Host bridge: Intel Corp. 82815 815 Chipset Host Bridge and Memory
Contr)
Subsystem: Intel Corp. 82815 815 Chipset Host Bridge and Memory
Controlb
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Ste-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort--
Latency: 0
Capabilities: [88] #09 [f104]
00:02.0 VGA compatible controller: Intel Corp. 82815 CGC [Chipset Graphics
Cont)
Subsystem: Hewlett-Packard Company: Unknown device 1245
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Ste-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbor-
Latency: 0
Interrupt: pin A routed to IRQ 10
Region 0: Memory at f0000000 (32-bit, prefetchable) [size=64M]
Region 1: Memory at ec000000 (32-bit, non-prefetchable) [size=512K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3ho)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:1e.0 PCI bridge: Intel Corp. 82801AA PCI Bridge (rev 02) (prog-if 00
[Normal)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Ste-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort--
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
I/O behind bridge: 00002000-00002fff
Memory behind bridge: ec100000-ec1fffff
Prefetchable memory behind bridge: fff00000-000fffff
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
00:1f.0 ISA bridge: Intel Corp. 82801AA ISA Bridge (LPC) (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Ste-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbor-
Latency: 0
00:1f.1 IDE interface: Intel Corp. 82801AA IDE (rev 02) (prog-if 80
[Master])
Subsystem: Intel Corp. 82801AA IDE
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Ste-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbor-
Latency: 0
Region 4: I/O ports at 1800 [size=16]
00:1f.2 USB Controller: Intel Corp. 82801AA USB (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corp. 82801AA USB
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Ste-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbor-
Latency: 0
Interrupt: pin D routed to IRQ 11
Region 4: I/O ports at 1820 [size=32]
00:1f.3 SMBus: Intel Corp. 82801AA SMBus (rev 02)
Subsystem: Intel Corp. 82801AA SMBus
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Ste-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbor-
Interrupt: pin B routed to IRQ 9
Region 4: I/O ports at 1810 [size=16]
01:01.0 Communication controller: Tiger Jet Network Inc. Intel 537
Subsystem: Unknown device 8085:0003
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Ste-
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Ste-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbor-
Latency: 64 (250ns min, 32000ns max)
Interrupt: pin A routed to IRQ 5
Region 0: I/O ports at 2000 [size=256]
Region 1: Memory at ec100000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI+ D1- D2+ AuxCurrent=55mA
PME(D0+,D1-,D2+,D3h)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:04.0 Ethernet controller: 3Com Corporation 3c905C-TX/TX-M [Tornado] (rev
78)
Subsystem: Hewlett-Packard Company: Unknown device 1246
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
Ste-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbor-
Latency: 80 (2500ns min, 2500ns max), cache line size 08
Interrupt: pin A routed to IRQ 5
Region 0: I/O ports at 2400 [size=128]
Region 1: Memory at ec101000 (32-bit, non-prefetchable) [size=128]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3ho)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
----------------------------------------------------------------------------
---------
_______________________________________________
Asterisk-Users mailing list
Asterisk-Users@lists.digium.com
http://lists.digium.com/mailman/listinfo/asterisk-users
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk-users