similar to: Installed TDM02B - Problem when other end hangs up

Dear list, We have an weird problem with our FXO card (TDM01B). When I made a call using this channel, all goes well, the called phone rings but when the called phone answers the call. In me handset I can hear an weird sound like a "Clack". I tryed diferents TDM cards and modules, and my zapata.conf is like, language=en context=from-zaptel switchtype=national usecallerid=yes

I have a very strange problem I'm hoping someone has encountered already. I've scoured the internet for an answer to this one. My phone company provides no disconnect supervision. Hence I'm forced to use the busydetect feature. I have a TDM400 with two FXO ports. If I call from an internal extension to a landline and then hangup the landline Asterisk detects the busy signal

I've just had polarity reversal provisioned by our telco to test hangup detect with a TDM400P I've set hanguponpolarityswitch=yes in zapata.conf When I start Asterisk I get "ignoring hanguponpolarityswitch" in /var/log/asterisk/messages I assume that the option is either not valid or conflicts with another setting somewhere. Any ideas?

Hi, Im working with the following versions: -asterisk-1.2.12.1 -zaptel-1.2.9.1 And with the following card: 00:0d.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface Subsystem: Unknown device 8085:0003 Flags: bus master, medium devsel, latency 32, IRQ 201 I/O ports at c800 [size=256] Memory at fe000000 (32-bit, non-prefetchable)

hi: In my zapata.conf i have 4 fxo configured channels,for fxo number 1 to 3 i added polarity reversal property but for fxo number 4 i didnt add polarity reversal property but it still giving me on cosole that fxo number 4 is polarized (because the line on fxo number 4 is not polarized). what i want to do is to not let polarity reversal take effect on fxo number 4. that what i have in my

Hi all, I just installed an TDM02B. My system is a dell pc with linux 2.6.12-1.1456_FC4 asterisk-1.2.0-beta1 zaptel-1.2.0-beta1 libpri-1.2.0-beta1 in /etc/zaptel.conf I have (all others are default): fxsks=3-4 <--- I saw light in the ports channels=1-2 <--- change it to 3-4 has same result but... [root@nmsd0 asterisk]# /etc/rc.d/init.d/zaptel

OK, I think I may have found the problem for myself at least. Actually, a friend of mine suggested it. Apparently, Asterisk is a little too fast for the card. Placing a "w" in front of the number to insert a pause looks like it did the trick! Dial(ZAP/1/w5555555) Looks like it gives the card a chance to come online? So, at least in this case, it was not that Asterisk was keeping

Hi, I am using TDM400 card with 3 fxs and 1 fxo. I am struggling to detect hangup tone or disconnect supervision tone from my CO. I attached the recorded wav file which contains my telco's disconnect supervision. I am using , asterisk-1.4.33.1 dahdi-linux-complete-2.3.0.1+ 2.3.0 OS => Debian-lenny 5 users.conf ------------- [trunk_1] trunkname = pstn ; GUI

Hi all.. I have a problem with my asterisk installation. I'm using a Wilcard X100P clone in Spain. Incoming calls work fine, but when I make a outgoing call, a hear the ringing, and the peer phone ring, when the peer answer, asterisk hangup the call, or say busy. This is my conf: zaptel.conf: --------- loadzone = es defaultzone=es fxsks=1 zapata.conf ---------- [channels]

Hi all, We have tested both tdm400 and BRI 1 port HFC based with mISDN driver and with both cards we have the same problem... so probably it's due to our misconfiguration, but we couldn't find anything useful on google. With TDM400 we can place and receive calls, but if we receive a call from TDM400 and we reject it from a sip phone , asterisk send the hangup but the line continue to

I am trying to reconfigure an asterisk box that was using an HFC-S card with bristuff but is now using 2 analog lines therefore I want to use the TDM02B to connect to two POTS lines. The TDM02B has 2 red modules. I have this in /etc/zaptel.conf loadzone=nl defaultzone=nl fxsks=1-2 I have /etc/asterisk/zapata.conf signalling=fxs_ks echocancel=yes echocancelwhenbridged=yes echotraining=400

Hello... I have a big problem with asterisk. Every time i make a call asterisk does not bridge the zap channels. The zap channel from which i'm calling remains in state:ring and applicaton:dial and the zap channel with the external line configured remains in state:dialling an Application:AppDial. Zap/20-1 agentie s 1 Dialing AppDial (Outgoing Line) 09399 (None) Zap/9-1 int_omg 09399 5 Ring

hello, I have instaled a analog line, and when I call on the console apears that: I want to redirect the call to 101 extension. *CLI> -- Starting simple switch on 'Zap/1-1' == Starting Zap/1-1 at default,s,1 failed so falling back to exten 's' == Starting Zap/1-1 at default,s,1 still failed so falling back to context 'default' Apr 27 08:15:53 WARNING[3494]:

I have one TDM2404E digium card on asterisk box, after configuring the zaptel and zapata configuration files, I am getting these errors when reloading asterisk: ast_unregister_indication_country: Removed default indication country 'us' setup_zap: Ignoring signalling setup_zap: Ignoring answeronpolarityswitch unable to recognize channel 13-5 what is the reason for that? Thanks,

Hello, I've one astribank with 8 FXO unit and 8 pstn lines connected to the astribank. When I receive calls on my ipphone I get always Unknown callerid. It's is possible to receive the callerid from the lines on the astribank unit? This is my config: [channels] language=es context=from-zaptel signalling=fxs_ks ;rxwink=300 usecallerid=yes callerid=asreceived ;cidsignalling=bell

Hi, I have a problem with polarity reverse this my dahdi config [channels] context=default usecallerid=yes hidecallerid=no callwaiting=yes usecallingpres=yes callwaitingcallerid=yes threewaycalling=yes transfer=yes canpark=yes cancallforward=yes callreturn=yes echocancel=yes echocancelwhenbridged=yes relaxdtmf=yes rxgain=0.0 txgain=0.0 group=1 callgroup=1 pickupgroup=1

Hello guys, I have this problem when a call is received in my PBX: (Caller) --> (Redirecting Service) --> (E1 PRI) --> (Asterisk PBX) --> (Internal Phone) Reception works fine, but when conversation finishes and the agent at internal phone hangs up, the call at caller's side is still alive for many seconds until it hangs up. The problem is that Telephone Company is billing me

Hi, Im getting mad with this error, I have a x100p installed with wcfxo module loaded perfectly, I can receive incoming calls and detect very good the hangup for incoming calls. But for outgoing calls its a mess. When I place a call for outgoing, i heard the ringing, my cell or phone rings and when I pick up the phone it hangs: -- Called g1/91xxxxxxx -- Hungup

Today I received a TDM11B (1 FXO and 1 FXS) and got it installed just fine. I bought the card mainly to get caller ID to work properly in Sweden, and that works just fine. However, if the called or calling party hangs up after I hangup my SIP channel, polarity CID detection kicks in and dials a couple of signals to my incoming context. This happens with Asterisk 1.0.6 and CVS-HEAD. I have tried

i am have x100P clone, and install asterisk 1.4 and out call normaly and hangup in xlite to zap but call to asterisk for zap channel nop pass to xlite and the caller hangup the asterisk not detect. what is the problem ??? -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20070720/39d4c1e8/attachment.htm